QQ: 859818709

Spectral Bandwidth Calculator

Spectral Bandwidth Calculator

Spectral Bandwidth Conversion Calculator (Δλ ↔ Δν)
Convert spectral bandwidth between the wavelength domain (Δλ: pm / nm / μm) and the frequency domain (Δν: kHz / MHz / GHz / THz), also giving the conversion factor, coherence length, coherence time, Q factor, wavenumber bandwidth and transform-limited pulse duration. Three input modes are supported — ‘known Δλ’, ‘known Δν’ and ‘two-band-edge wavelengths’ — and the deviation between the exact formula and the common approximation is given.
Δν ≈ c·Δλ / λ₀² · 1 nm at 1064 nm ≈ 264.8 GHz, 1 nm at 1550 nm ≈ 124.8 GHz
Common quick answers (intensity FWHM basis; the centre wavelength must be given, and for narrow bands Δν ≈ c·Δλ/λ₀²)
1064 nm,1 nm≈ 264.81 GHz
1550 nm,1 nm≈ 124.78 GHz
1550 nm,100 GHz≈ 0.8014 nm
1550 nm,1 MHz≈ 8.014 fm






Common centre wavelengths


Common bandwidths



Key results
Full data table
Conversion factor vs. centre wavelength (Δν / Δλ)
Approximation error vs. relative bandwidth

Key equations and principles

Wavelength and frequency
λ = c / ν  ,  c = 299 792 458 m/s
All bandwidth conversions follow from this single nonlinear relation. c is the speed of light in vacuum; the refractive index of air is about 1.0003 and can be ignored in engineering conversions, while high-precision applications need to divide by the group refractive index.
Narrow-band approximation (most commonly used)
Δν ≈ c · Δλ / λ₀²
Differentiating ν = c/λ gives |dν| = c·dλ/λ², replacing the differential with a finite bandwidth. λ₀ must be thecentre wavelength, not the bandwidth. The coefficient is 264.8 GHz/nm at 1064 nm and 124.8 GHz/nm at 1550 nm.
Exact formula (band-edge mapping)
Δν = c·Δλ / (λ₁·λ₂) = c·Δλ / (λ₀² − Δλ²/4)
Convert each band edge to frequency separately and then subtract, with no approximation. The Δλ²/4 term in the denominator is exactly the amount by which the exact result exceeds the approximate one.
Inverse exact formula
Δλ = c·Δν / (ν₀² − Δν²/4)
Recovers the wavelength bandwidth from a known frequency bandwidth. Used when converting WDM (wavelength division multiplexing) channel spacings (100 GHz, 50 GHz) to nm.
Magnitude of approximation error
(Δνexact − Δνapproximate) / Δνapproximate ≈ (Δλ / 2λ₀)²
For a bandwidth of 1% of the wavelength the deviation is about 0.0025% (2.5×10⁻⁵, negligible); at 10% it is about 0.25%, and at 50% it reaches about 6.7%, where the exact formula must be used.
Wavenumber and photon energy bandwidth
Δν̃ = Δν / c  ,  ΔE = h·Δν
Wavenumber and frequency arestrictly linear (1 cm⁻¹ = 29.9792458 GHz), with no approximation here; it is wavelength and wavenumber that are nonlinear. Photon energy is likewise linear.
Coherence length and coherence time
Lc = c / Δν  ,  τc = 1 / Δν
This is an engineering convention (equivalent to Lc = λ₀²/Δλ). Defined strictly by lineshape: for a Gaussian spectrum, the first-order complex degree of coherence |g₁(τ)| falling to 1/e corresponds to 0.530/Δν, and for a Lorentzian spectrum to 1/(πΔν) = 0.318/Δν.
Transform-limited pulse duration
Δt · Δν = 0.441 (Gaussian) / 0.315 (sech², squared hyperbolic secant)
Both Δt and Δν are intensity FWHM. This is the lower limit given by the Fourier transform; actual pulses are only wider (chirp and dispersion add broadening). The 0.441 here and the 0.530 for coherence time are different quantities — do not mix them up.

Quick reference of conversion factors for common wavelengths

In the table, ‘GHz/nm’ = c/λ₀², i.e. the frequency interval corresponding to 1 nm of bandwidth at that wavelength; ‘1 GHz → pm’ is its reciprocal, used to convert a frequency linewidth back to a wavelength linewidth. Values are calculated with c = 299 792 458 m/s.

Laser wavelength λ₀ Centre frequency ν₀ (THz) 1 nm → GHz 1 GHz → pm Typical source
405 nm 740.228 1827.72 0.5471 Blue-violet diode laser / maskless lithography
488 nm 614.329 1258.87 0.7944 Ar⁺ laser / flow cytometry
532 nm 563.520 1059.25 0.9441 Frequency-doubled Nd:YAG, green pointer
633 nm 473.606 748.19 1.3366 He-Ne laser / interferometry
780 nm 384.349 492.76 2.0294 Rb atomic clock / atomic physics
808 nm 371.030 459.20 2.1777 Nd:YAG pumping
915 nm 327.642 358.08 2.7927 Fibre laser pumping
1030 nm 291.061 282.58 3.5388 Yb:YAG femtosecond laser
1064 nm 281.760 264.81 3.7763 Nd:YAG / fibre laser
1310 nm 228.849 174.69 5.7243 O-band optical communication (zero dispersion)
1550 nm 193.414 124.78 8.0139 C-band optical communication / eye-safe
2000 nm 149.896 74.95 13.3426 Mid-infrared pumping / medical
10.6 μm 28.282 2.67 374.79 CO₂ laser / cutting

Calculation examples

Example 1: 1064 nm Nd:YAG with a 1 nm wavelength bandwidth

Given:λ₀ = 1064 nm,Δλ = 1 nm(FWHM)
  1. Band edges: λ₁ = 1063.5 nm, λ₂ = 1064.5 nm
  2. Δν = c·Δλ/(λ₁λ₂) = 2.998×10⁸ × 1×10⁻⁹ / (1.0635×10⁻⁶ × 1.0645×10⁻⁶) ≈ 264.81 GHz
  3. Approximation check: c·Δλ/λ₀² = 264.81 GHz, differing from the exact value by 0.00002% (the bandwidth is only 0.094% of the centre wavelength)
  4. Coherence length Lc = c/Δν ≈ 1.132 mm;Q = ν₀/Δν ≈ 1064
Result: Δν = 264.81 GHz, wavenumber bandwidth 8.833 cm⁻¹, photon energy bandwidth 1.095 meV, transform-limited pulse duration (Gaussian) 1.665 ps

Example 2: 1550 nm WDM — how many nm does a 100 GHz channel spacing correspond to?

Given:λ₀ = 1550 nm,Δν = 100 GHz
  1. ν₀ = c/λ₀ ≈ 193.41 THz,ν₁ = 193.4645 THz,ν₂ = 193.3645 THz
  2. λ₁ = c/ν₁ ≈ 1549.599 nm,λ₂ = c/ν₂ ≈ 1550.401 nm
  3. Δλ = λ₂ − λ₁ ≈ 0.8014 nm (the industry rule of thumb ‘100 GHz ≈ 0.8 nm’ comes from here)
Result: Δλ = 0.8014 nm, coherence length 2.998 mm, Q ≈ 1934

Example 3: 800 nm Ti:sapphire — how short a pulse can a 10 nm bandwidth support?

Given:λ₀ = 800 nm,Δλ = 10 nm
  1. Δν = c·Δλ/(λ₁λ₂),λ₁ = 795 nm、λ₂ = 805 nm → Δν ≈ 4.6844 THz
  2. Approximation error 0.0039% (the bandwidth is already 1.25% of the centre wavelength, but the error is still negligible)
  3. Gaussian transform limit Δt = 0.441/Δν ≈ 94.1 fs; for sech² it is 0.315/Δν ≈ 67.2 fs
Result: Δν = 4.6844 THz, transform-limited pulse duration 94.1 fs (Gaussian) / 67.2 fs (sech²), coherence length 64.0 μm

Example 4: 1550 nm DFB (distributed feedback) laser — what wavelength does a 1 MHz linewidth correspond to?

Given:λ₀ = 1550 nm,Δν = 1 MHz
  1. Δλ = c·Δν/(ν₀² − Δν²/4) ≈ 8.014×10⁻¹⁵ m
  2. 8.0 fm cannot be read at all in the wavelength domain — this is exactly why narrow-linewidth lasers always specify linewidth in frequency
  3. Coherence length Lc = c/Δν = 299.79 m
Result: Δλ = 8.014 fm (= 8.014×10⁻⁶ nm), coherence length 299.79 m, wavenumber bandwidth 3.34×10⁻⁵ cm⁻¹

Common misuses

Substituting λ and Δλ in the wrong places

The denominator of Δν = c·Δλ/λ₀² is thesquare of the centre wavelength, the numerator is thebandwidth. Solving in reverse for wavelength bandwidth gives Δλ = λ₀²·Δν/c. Putting the bandwidth in the denominator and the wavelength in the numerator is the most frequent calculation error, off by up to a factor of 10⁶.

Still using the approximation for broad bandwidths

The deviation of the approximation is (Δλ/2λ₀)².At a bandwidth of 10% of the wavelength the deviation is about 0.25%, and at 50% about 6.7%, a level often reached by supercontinuum sources, LEDs and femtosecond oscillator outputs. For such inputs, refer directly to the ‘exact value’ in the data table.

Confusing pulse duration, coherence time and 1/Δν

All three equal ‘constant/Δν’, but with different constants:Gaussian transform-limited pulse duration 0.441, Gaussian |g₁| coherence time 0.530, engineering convention 1, Lorentzian 0.318. Using 1/Δν as the pulse duration overestimates by about a factor of 2.3 (equivalent to overestimating the pulse width, Gaussian), enough to misjudge the order of magnitude in ultrafast experiments.

Frequently asked questions (FAQ)

Why is 1 nm equal to 265 GHz at 1064 nm but only 125 GHz at 1550 nm?

Because the denominator of Δν ≈ c·Δλ/λ₀² is the square of the wavelength. The longer the wavelength, the smaller the relative bandwidth for the same wavelength interval, and the smaller the frequency interval. The coefficient c/λ₀² is 264.8 GHz/nm at 1064 nm and 124.8 GHz/nm at 1550 nm, differing by exactly (1550/1064)² ≈ 2.12. So ‘how many GHz is 1 nm’ must always be stated with the wavelength; on its own it is meaningless.

Which is more fundamental, Δλ or Δν?

The frequency domain is more fundamental. Fourier transforms, photon energy, coherence time and transform-limited pulse duration all take frequency as the natural variable, and the relation between frequency bandwidth and lineshape is more direct (a Gaussian spectrum remains Gaussian in the frequency domain but becomes slightly asymmetric when mapped to wavelength). The advantage of the wavelength domain is that it matches the labelling conventions of spectrometers, coatings and filters. Neither is right or wrong, but for coherence or ultrafast pulse durations it is advisable to standardise on Δν.

When must the exact formula be used?

The criterion is the relative bandwidth Δλ/λ₀. When the bandwidth is below 1% of the centre wavelength the approximation error is about 0.0025% (2.5×10⁻⁵), completely negligible; at 10% it is about 0.25%, still acceptable for most engineering; above 20%–30% (supercontinuum, LED, broadband femtosecond) the exact formula should be used. The data table of this tool gives both values and the relative deviation, with an automatic warning above 5%.

Why does a band symmetric in the frequency domain become asymmetric in the wavelength domain?

Because λ = c/ν is a hyperbolic mapping, not a linear scaling. Equally spaced ticks in the frequency domain have different spacings everywhere after mapping to wavelength (e.g. 100 GHz channels equally spaced in frequency have unequal wavelength intervals). Strictly speaking, a band of ‘centre wavelength ±Δλ/2’ is not centred on ν₀ in the frequency domain — the short-wavelength side spans a larger frequency range; the ‘frequency-domain asymmetry’ in this tool’s data table is exactly this ratio, which is extremely close to 1 for narrow bands and can be ignored.

Should the coherence length use c/Δν or λ₀²/Δλ?

The two are equivalent for narrow bands: c/Δν = c/(cΔλ/λ₀²) = λ₀²/Δλ. The strict form is Lc = λ₁λ₂/Δλ, exactly consistent with c/Δν (since Δν = cΔλ/(λ₁λ₂)). The only difference is whether the Δλ²/4 term is neglected; for bandwidths below 1% of the wavelength the two differ by less than 10⁻⁴ in relative terms.

Why are there three forms of coherence time: 1/Δν, 0.530/Δν and 1/(πΔν)?

Because ‘coherence time’ has no unique definition — it depends on the lineshape and criterion. The engineering convention τc = 1/Δν is used for order-of-magnitude estimates; for a Gaussian spectrum, |g₁(τ)| falling to 1/e corresponds to 0.530/Δν; for a Lorentzian spectrum to 1/(πΔν) = 0.318/Δν. The differences between these three values arise from different definitions of lineshape and criterion, representing real physical differences, not calculation errors.

Where do the 0.441 and 0.315 for transform-limited pulse duration come from?

They come from the analytical result of the Fourier transform of the lineshape: for a spectrum with Gaussian intensity and FWHM Δν, the intensity envelope of its Fourier transform has FWHM 0.441/Δν; for a sech² spectrum it is 0.315/Δν; for a rectangular spectrum 0.886/Δν. The constant depends only on the lineshape, not on the centre wavelength. Real lasers are always wider due to chirp and dispersion, so these two values serve only as lower-limit references.

How does this tool differ from the site’s ‘wavelength/frequency/photon energy converter’?

That tool handlespoint-value conversion: 1064 nm ↔ 281.76 THz ↔ 1.165 eV, valid for any wavelength (wavelength/frequency/photon energy converter). This tool handlesinterval-width conversion: Δλ ↔ Δν. Bandwidth cannot simply copy the point-value ratio, because λ and ν are nonlinearly related — this is precisely why this tool is provided separately. Use the two together: first fix the centre with the point-value conversion, then convert the width with this tool.

How do I choose units? Which should I use: pm, nm, GHz, THz or cm⁻¹?

By convention: coatings, filters and spectrometers use nm or pm; narrow-linewidth lasers, WDM and coherent communications use GHz or MHz; spectroscopy (Raman, absorption) uses cm⁻¹; ultrafast work uses THz together with fs. This tool computes entirely in SI internally and automatically selects a suitable magnitude for output. cm⁻¹ and GHz are strictly linear (1 cm⁻¹ = 29.9792458 GHz), so you can multiply or divide directly without worrying about approximation.

Can it still calculate when the bandwidth exceeds 10% of the centre wavelength?

Yes, but the basis must be clear. Mathematically it holds as long as the band edges remain positive; physically, for broad bands the very definitions of ‘centre wavelength’ and ‘FWHM’ become ambiguous (the spectrum is strongly asymmetric), so it is more appropriate to give the full spectral curve rather than a single bandwidth value. This tool prompts you to use the exact value when the relative bandwidth exceeds 5% and recommends direct integration of the spectral data above about 30%.

How do I convert between FWHM, RMS and 1/e² bandwidth?

A definite relation exists only for Gaussian spectra: FWHM = 2.355σ (σ is the standard deviation, i.e. the RMS width). The 1/e full intensity width = 2√2σ ≈ 2.828σ, hence FWHM = 0.833 × (1/e full width); the 1/e² full intensity width commonly used in datasheets (where the intensity falls to 1/e² of the peak) = 4σ, hence FWHM = 0.589 × (1/e² full width), i.e. the 1/e² full width ≈ 1.699 × FWHM. A Lorentzian spectrum has no finite RMS width (the integral diverges) and cannot be converted this way. All inputs and outputs of this tool use the intensity full width at half maximum (FWHM) basis; mixing other bases will systematically overestimate or underestimate the result.

中文EN