QQ: 859818709

Abbe Number Calculator

Abbe Number Calculator

Abbe Number Calculator (Abbe Number Calculator)
Enter the refractive indices of an optical material at the Fraunhofer lines (F blue / d yellow / C red) to calculate online the Abbe number V_d (dispersion coefficient / Abbe value), the dispersive power ω = 1/V_d and the glass category (crown / flint), and to estimate the F–C axial chromatic aberration of a single lens. The V_e definition and back-calculation of a missing refractive index are also supported.
V_d = (n_d − 1) / (n_F − n_C) , ω = 1 / V_d

Abbe number calculation

Refractive indices are taken from the manufacturer’s datasheet values at the F/C/d (or e/F′/C′) lines, with wavelengths fixed at 486.1 / 656.3 / 587.6 nm.

① Calculate V_d (d/F/C lines)
② Calculate V_e (e/F′/C′ lines)
③ Back-calculate a missing parameter

mm



Enter the other three quantities to solve.

Example glasses (click to load d/F/C-line refractive indices)

Distribution of common optical glasses in the (n_d, V_d) plane: the upper left contains crown glasses (low refractive index, high Abbe number, low dispersion), the lower right flint glasses (high refractive index, low Abbe number, high dispersion); the two dashed lines at V_d = 55 and V_d = 50 are the classification boundaries, with a transition region between them.

Core formulae and principles

1
Abbe number V_d (standard definition)
V_d = (n_d − 1)/(n_F − n_C)
n_d, n_F and n_C are the refractive indices of the material at the d (587.6 nm), F (486.1 nm) and C (656.3 nm) Fraunhofer lines, respectively. The larger V_d is, the smaller the dispersion.
2
Dispersive power ω (reciprocal dispersion)
ω = (n_F − n_C)/(n_d − 1) = 1/V_d
The principal dispersion is the difference in refractive index between the F and C lines, n_F − n_C; the dispersive power (also called reciprocal dispersion) ω = (n_F − n_C)/(n_d − 1) = 1/V_d describes the relative magnitude of dispersion in the visible region. Note that it is not the same concept as ‘partial dispersion’ n_λ1 − n_λ2 or ‘relative partial dispersion’ (n_λ1 − n_λ2)/(n_F − n_C).
3
Abbe number V_e (e-line definition)
V_e = (n_e − 1)/(n_F′ − n_C′)
Based on the mercury green e-line (546.1 nm), paired with the cadmium blue F′ (480.0 nm) and cadmium red C′ (643.8 nm) lines. Some older datasheets use V_e, while modern ones mostly use V_d; the two values are close but not identical.
4
Glass classification (by V_d)
V_d > 55 crown; V_d < 50 flint
V_d > 55 denotes a crown glass, with low dispersion; V_d < 50 denotes a flint glass, with high dispersion and a high refractive index; 50–55 is the transition region. The classification depends only on V_d and has no simple correspondence to the absolute refractive index (a high-index lanthanum crown can also have V_d above 55).
5
Axial chromatic aberration of a thin lens (F–C)
Δf = f / V_d
For a thin lens in air, the separation of the F- and C-line foci (axial chromatic aberration) |f_F − f_C| ≈ the focal length f divided by V_d. The larger V_d is, the smaller the aberration — this is the basis of combining crown and flint glasses in achromatic doublet design.
6
Relative chromatic aberration
Δf / f = 1 / V_d = ω
The ratio of axial chromatic aberration to focal length equals the reciprocal of the Abbe number, so once a material is chosen the relative chromatic aberration of a thin lens is fixed and can only be cancelled by combining materials with different V_d values (apochromatic correction requires anomalous partial dispersion materials).
Spectral-line wavelengths (Fraunhofer lines):C = 656.3 nm (hydrogen red), d = 587.6 nm (helium yellow), e = 546.1 nm (mercury green), F = 486.1 nm (hydrogen blue), F′ = 480.0 nm (cadmium blue), C′ = 643.8 nm (cadmium red).
Always use refractive indices from a datasheet of the same manufacturer and under the same measurement conditions; mixing sources introduces systematic error. The three-line refractive indices of the example glasses are taken from official values in public catalogues such as SCHOTT’s, and the V_d recalculated from V_d = (n_d − 1)/(n_F − n_C) generally differs from the manufacturer’s stated value by ≤ 0.05.

Common optical glass reference (n_d and V_d taken from manufacturers’ datasheets)

Grade Type n_d V_d Dispersive power 1/V_d Typical applications
N-BK7 (SCHOTT) Crown 1.51680 64.17 0.01558 General lenses and prisms
N-BK10 (SCHOTT) Crown 1.49782 66.95 0.01494 Low-dispersion elements
N-BAK4 (SCHOTT) Crown 1.56883 55.98 0.01786 Photographic objectives
LLF1 (SCHOTT) Flint 1.54814 45.75 0.02186 Achromatic components
F2 (SCHOTT) Flint 1.62004 36.37 0.02749 Achromatic flint elements
SF2 (SCHOTT) Flint 1.64769 33.85 0.02954 High-dispersion prisms
N-SF5 (SCHOTT) Flint 1.67270 32.25 0.03101 Dispersive elements
SF11 (legacy grade) Flint 1.78472 25.77 0.03888 Strong dispersion, high refractive index (lead-containing; see N-SF11 for a lead-free alternative, ν_d≈25.68)
N-LASF9 (lanthanum flint) Flint 1.85025 32.17 0.03108 High-index, low-dispersion flint
Fused Silica Crown 1.45846 67.82 0.01475 UV / deep UV, laser optics
CaF₂ (calcium fluoride) Crown 1.43385 95.10 0.01052 IR / UV windows
Sapphire (o-ray) Crown 1.76817 72.30 0.01383 Wear-resistant windows (o-ray; uniaxial negative crystal, n_e≈1.760)
FK51A (legacy grade) Crown 1.48749 84.47 0.01184 Apochromatic (APO) design
Anomalous Partial Dispersion:Most ‘normal’ glasses lie approximately on a straight line when relative partial dispersion P_{F,d} is plotted against V_d; materials that deviate from this line (such as the FK series and fluorite CaF₂) are called anomalous partial dispersion glasses and are
key materials for designing apochromatic (APO) lenses with extremely low secondary spectra. The V_d and 1/V_d calculated by this tool allow a preliminary screening of such glasses; for a rigorous APO assessment you also need the relative partial dispersion P_g,F and its deviation ΔP from the normal line.

Frequently asked questions (FAQ)

What is the Abbe number (V_d)?

The Abbe number is a dimensionless parameter that measures the dispersion of a transparent optical material (the variation of refractive index with wavelength); it is defined as V_d = (n_d − 1)/(n_F − n_C), where n_d, n_F and n_C are the refractive indices at the three Fraunhofer lines d (587.6 nm), F (486.1 nm) and C (656.3 nm), respectively. The larger V_d is, the smaller the material’s dispersion.

Is a larger or a smaller Abbe number better?

There is no absolute ‘good’ or ‘bad’: a large V_d means low dispersion (crown glass), which helps reduce chromatic aberration; a small V_d means high dispersion (flint glass), usually with a higher refractive index. Achromatic lenses in fact require combining a high-V_d crown with a low-V_d flint, using their opposing dispersions to cancel aberration.

How are crown and flint glasses distinguished?

By V_d: V_d > 55 is crown glass, V_d < 50 is flint glass, and 50–55 is the transition region. Traditional flints often used lead oxide to achieve high dispersion; modern N-series flints are generally lead- and arsenic-free. Flints share a low V_d (high dispersion), and usually have higher density and refractive index.

What is the difference between V_d and V_e?

V_d uses the d line (587.6 nm) as its central wavelength, with the F (486.1) and C (656.3) lines; V_e uses the e line (546.1 nm), with F′ (480.0) and C′ (643.8). Both are Abbe numbers, with close but different values, so check whether a datasheet quotes V_d or V_e.

What is the dispersive power ω (reciprocal dispersion), and how does it relate to the Abbe number?

The dispersive power (also called reciprocal dispersion) ω = (n_F − n_C)/(n_d − 1) is exactly the reciprocal of the Abbe number (ω = 1/V_d). It describes the relative refractive-index span of a material across the visible blue–red range and is central to calculating lens axial chromatic aberration and designing apochromatic systems. Note that it is not the same concept as ‘partial dispersion’ n_λ1 − n_λ2 or ‘relative partial dispersion’ (n_λ1 − n_λ2)/(n_F − n_C).

How can I use the Abbe number to estimate a lens’s chromatic aberration?

For a thin lens in air, the separation of the F- and C-line foci (axial chromatic aberration) ≈ Δf = f / V_d, where f is the focal length. The relative chromatic aberration Δf/f = 1/V_d = ω depends only on the material, not on the absolute focal length. Clearly, the larger V_d is, the smaller the aberration.

What is anomalous partial dispersion, and why is it needed for APO lenses?

The relative partial dispersion P_{F,d} of ‘normal’ glasses lies approximately on a straight line against V_d; materials that deviate from this line (such as the FK series and fluorite CaF₂) are called anomalous partial dispersion glasses. An ordinary cemented doublet corrects only first-order chromatic aberration; apochromatic (APO) designs rely on the anomalous partial dispersion of these materials to suppress the secondary spectrum (residual aberration) to a very low level.

Which spectral line should be used for the refractive index?

You must use refractive indices from a datasheet of the same manufacturer under the same measurement conditions, with matching lines: for V_d use n_d, n_F, n_C (corresponding to 587.6 / 486.1 / 656.3 nm); for V_e use n_e, n_F′, n_C′. Mixing refractive indices from different sources introduces systematic error and gives an incorrect V_d.

Why do I get the message ‘n_F should be greater than n_C’ after entering the refractive indices?

The F line (486.1 nm) has a shorter wavelength than the C line (656.3 nm), and under normal dispersion shorter wavelengths have higher refractive indices, so n_F > n_C must hold. If you enter n_F ≤ n_C, you have swapped the values, used inconsistent sources / units, or the material shows anomalous dispersion in this region — check your data.

Can this calculator back-calculate a missing refractive index?

Yes. In the ‘③ Back-calculate a missing parameter’ mode, select the quantity to solve for (V_d, n_d, n_F or n_C) and enter the other three. For example, given n_d, n_F and n_C you can find V_d; or given V_d, n_d and n_C you can derive n_F = n_C + (n_d − 1)/V_d. Back-calculated results are also checked for physical plausibility (V_d > 0, n_d > 1, n_C < n_d < n_F).

Does the Abbe number have units?

The Abbe number is dimensionless (a ratio of differences of refractive indices) and has no units. It is commonly written as V_d = 64.17; some datasheets use ν_d or ‘Abbe value’ instead.

中文EN