Description
Product Overview
PF0511-M01 is the infrared workhorse of the Thorlabs metallic Zerodur line: a 12.7 mm disc, 6.0 mm thick, coated with protected gold and specified at 96% average reflectance from 800 nm to 20 µm. Figure is lambda/10 peak to valley at 632.8 nm, polish is 40-20 scratch-dig, parallelism is 3 arcmin or better, the clear aperture is 90% of the diameter, and the item number is engraved on the back. The substrate is Zerodur, which holds 0 plus or minus 0.100 x 10-6/degC.
Gold is the only metal that stays highly reflective across the whole infrared without help from a dielectric stack, and that is why every CO2 delivery bench, every thermal imager and every Fourier-transform spectrometer has gold somewhere in the chain. The 800 nm band edge is the honest limitation: this coating reflects nothing useful in the visible, so a red alignment laser will not be visible in the return and a HeNe will have to be introduced coaxially. On a 10.6 µm CO2 line the same coating is comfortable, and at 3 to 5 µm it is the default fold in mid-infrared imaging relays.
The overcoat is the part buyers underestimate. Thorlabs writes that the overcoat of its protected mirrors results in polarization changes that can be difficult to quantify, and that it sometimes induces absorption in the mid- to far-infrared. Both statements are about this coating. What you buy with them is a surface that can be cleaned, and a film that will not fail the first time somebody touches it. What you give up is exact polarization fidelity and a fraction of a percent of throughput beyond about 7 µm. If either matters more than cleanability, the unprotected gold -M03 is the correct part and the 1% reflectance difference is the smaller of the two arguments for it.
Laser ratings for the coating are 2 J/cm2 at 1064 nm for 10 ns pulses at 10 Hz over a 1.000 mm spot, and 500 W/cm CW at 1.070 µm over 0.089 mm or 750 W/cm CW at 10.6 µm over 0.339 mm. The same film is available on a fused silica body as the PF05-03-M01 if thermal drift is not a concern, and in Ø1 inch and Ø2 inch versions on the same Zerodur platform.
Key Features
- 96% average from 800 nm to 20 µm: one film covers the near, mid and far infrared, which is why gold survives every source change in an IR lab
- SiO2 overcoat: the gold is protected, so a solvent wipe is permitted instead of forbidden
- Zerodur body: 0 plus or minus 0.100 x 10-6/degC keeps a CO2 fold stable while the tube warms the bench
- 0 to 45 degree incidence: specified for the folding geometry of real delivery optics, not just for a normal-incidence test bench
- Documented trade-off: Thorlabs states the overcoat shifts polarization in ways that are hard to quantify and absorbs slightly in the mid to far infrared
- Laser rated: 2 J/cm2 pulsed at 1064 nm, 750 W/cm CW at 10.6 µm
Technical Specifications
| Parameter | Value |
|---|---|
| Item Number | PF0511-M01 |
| Coating | Protected Gold (gold plus dielectric protective overcoat) |
| Wavelength Range | 800 nm to 20 µm |
| Average Reflectance | 96% from 800 nm to 20 µm |
| Angle of Incidence | 0 to 45 degrees |
| Substrate | Zerodur (Schott registered trademark, substrate grade) |
| Diameter | 12.7 mm (1/2 inch), +0.0 / -0.1 mm |
| Thickness | 6.0 mm (0.24 inch), plus or minus 0.2 mm |
| Clear Aperture | 90% of the diameter |
| Front Surface Flatness | lambda/10 peak to valley at 632.8 nm |
| Surface Quality | 40-20 scratch-dig |
| Parallelism | 3 arcmin maximum |
| Coefficient of Thermal Expansion | 0 plus or minus 0.100 x 10-6/degC |
| Back Surface | Fine ground, item number engraved |
| Pulsed Damage Threshold | 2 J/cm2 at 1064 nm, 10 ns, 10 Hz, over 1.000 mm |
| CW Damage Threshold | 500 W/cm at 1.070 µm over 0.089 mm; 750 W/cm at 10.6 µm over 0.339 mm |
| Source | Thorlabs official series specification table |
Reflectance is an average over the stated band, not a flat floor. Thorlabs publishes the measured curve on the Graphs tab of the series page, and outside the shaded band the numbers are typical rather than guaranteed and can vary from lot to lot.
Applications
- CO2 laser delivery: 10.6 µm folding mirrors in the articulated arm or the gantry of a cutting machine, where 750 W/cm CW is the relevant rating
- Thermal imaging relays: 3 to 5 µm and 8 to 12 µm optics that have to fold a warm scene without adding emission of their own
- FTIR and infrared spectroscopy: sample and reference arms where a broadband metal is preferred over a narrow dielectric stack
- Mid-infrared source collimation: quantum cascade lasers and OPO outputs, where the beam is weak and the 96% matters more than the handling convenience
- Pyrometry and radiometry: sighting optics on furnaces and melt streams, often in an enclosure where a cleanable coating is worth having
Selection Guide
Gold is chosen by band first and by handling second. If the answer to the band question is already gold, the remaining decisions are mechanical.
- 800 nm to 20 µm, one part, cleanable: this item, PF0511-M01.
- 2 µm to 20 µm only, and you want the last two points: the mid-infrared enhanced gold -M02 reaches 98% over 2 to 20 µm but gives up a great deal in the near infrared, so it is a specialist part, not an upgrade.
- Polarization state has to be preserved, or pulses are short: unprotected gold -M03, at 97%, with no overcoat to shift polarization or add dispersion.
- 10.6 µm line only, highest possible reflectance: the laser-line gold -L01 is specified at 99% at 10.6 µm, at the cost of everything else in the band.
- Visible alignment through the same optic: not possible with gold. Use a flip-in reference mirror or a dichroic instead of trying to make one coating do both jobs.
Series Comparison
The four infrared coatings Thorlabs offers on this platform, ranked by what each one is actually for rather than by headline reflectance.
| Coating | Band | Average Reflectance | Trade-Off |
|---|---|---|---|
| -M01 Protected Gold | 800 nm to 20 µm | 96% | Cleanable; overcoat shifts polarization and absorbs slightly far out |
| -M02 MIR Enhanced Gold | 2 µm to 20 µm | 98% | Best mid-IR figure; near infrared performance is deliberately sacrificed |
| -M03 Unprotected Gold | 800 nm to 20 µm | 97% | Highest gold reflectance and clean polarization; surface cannot be touched |
| -L01 Laser Line Gold | 10.6 µm | 99% | Narrowband only; unusable as a broadband fold |
FAQ
Gold or silver at 1.06 µm? Silver is the brighter film there, and on the same Zerodur body the protected silver -P01 is specified at 97% from 450 nm to 2 µm against 96% for gold. Gold wins only if the same optic also has to work beyond 2 µm, which in a Nd:YAG bench it usually does not. Do not buy gold for 1064 nm on the strength of its infrared reputation.
Will the overcoat spoil an interferometer? It can. A dielectric overcoat is a thin film, a thin film has a phase response, and at oblique incidence that response differs for s and p polarization. Thorlabs describes the resulting polarization change as difficult to quantify. In a two-beam interferometer where both arms use the same coating the error largely cancels; in a polarimetric measurement it does not, and that is the case for -M03.
Can it be used at 45 degrees? Yes. Thorlabs specifies the coating from 0 to 45 degrees incidence, which covers the folding angles used in delivery arms and periscopes. Reflectance curves shift with angle, so the published curve at 45 degrees is the one to read if your geometry is folded.
How much power will it take? The published coating ratings are 2 J/cm2 at 1064 nm for 10 ns at 10 Hz, and 750 W/cm CW at 10.6 µm. Both assume a clean surface and a beam well inside the clear aperture. A dust particle in the beam raises the local fluence by orders of magnitude, which is why the cleanability of this coating is a laser-safety feature and not merely a convenience.
Usage Precautions
- The overcoat may be cleaned, but only by the standard drag-wipe method with reagent-grade solvent and a fresh tissue. Gold underneath is soft; the overcoat is thin; a hard rub reaches the metal.
- Keep the part out of condensing atmospheres. Gold itself does not oxidise, but the overcoat can haze, and a hazed overcoat is an absorbing overcoat at 10.6 µm.
- Do not mount with a bare metal retaining ring bearing directly on the coating. Use a plastic or brass-tipped ring, and tighten only until the optic stops moving.
- Verify the band before installation. A gold mirror looks like a gold mirror under room light and will silently kill a 633 nm alignment beam.
- Store in a dust-tight container. In the infrared, dust is not cosmetic; it is a hot spot.
Disclaimer
Specifications on this page are transcribed from Thorlabs official public documentation and are provided for selection reference only. The current official specification sheet governs. Thorlabs may change specifications, coatings and appearance without notice. Prices, availability and delivery times are confirmed by our sales team at the time of order; nothing on this page is a binding offer.
Contact Us
Gaofei Laser supplies genuine Thorlabs stock and can quote this item with current availability, lead time and volume pricing. Send the item number, the quantity you need and the wavelength you are working at, and we will confirm the coating, the substrate and the mounting interface before you order.
- Sales hotline: +86 159 2722 0467
- Email: 859818709@qq.com
- Website: www.soar-laser.cn









Reviews
There are no reviews yet.