QQ: 859818709

Thorlabs PF10-03 Fused Silica Mirror Blank, Ø25.4 mm (1 in), 6.0 mm Thick

Thorlabs PF10-03 Fused Silica Mirror Blank, Ø25.4 mm (1 in), 6.0 mm Thick

Price on request
Category:

Description

Product Overview

The Thorlabs PF10-03 is an uncoated mirror blank: a Ø25.4 mm fused silica disc, 6.0 mm thick with a ±0.2 mm tolerance, front face figured better than λ/10 at 632.8 nm and polished to 10-5 scratch-dig, clear aperture 90 percent of the diameter, rear face fine ground and engraved with the item number. There is no film on it, so there is no reflectance figure on this page and no spectral band to respect. What you are buying is a substrate with a known figure and a known surface, and the coating decision is yours.

That is a deliberate position in a catalogue full of finished mirrors. A blank is what you order when the film you need does not exist as a stock item: a non-standard band, a dielectric design of your own, a coating developed in house, or a substrate that has to go to a coating house together with the rest of a project. It is also what you order when an existing optic has been damaged on its coated face and the substrate underneath is still good. The material is substrate-grade fused silica with high transmission from 185 nm to 2.1 µm, high purity and good environmental durability, so it tolerates the cleaning, bake-out and deposition steps that a coating run involves. A λ/20 figure is available as a custom order if the standard part is not tight enough.

The 25.4 mm diameter is the single most useful size in the catalogue, and the reason is mechanical rather than optical. One inch is the format the optomechanics industry standardised on: kinematic mounts, fixed mounts, retaining rings, thread adapters, posts and breadboard hardware are all built around it, in the largest numbers and at the lowest prices per part. A Ø1 inch optic drops into almost anything; anything else needs an adapter. If you are prototyping and do not yet know how the optic will be held, Ø1 inch is the choice that keeps the most doors open.

Where the blank stops being enough is thermal. Fused silica has a coefficient of thermal expansion around 0.55 x 10⁻⁶ per °C. Zerodur is specified at 0 ± 0.100 x 10⁻⁶ per °C, roughly five times flatter in temperature response and with a near-zero expansion at room temperature. For a bench that drifts a degree or two, fused silica is fine and cheaper. For an interferometer that is cycled between environments, a cavity that runs at high average power, or anything that must hold figure through a thermal transient, the expansion difference shows up directly in the wavefront and the Zerodur substrate is the correct answer.

Two diameters in this family get confused. Ø19 mm exists specifically for the Polaris fixed mounts: it gives a larger clear aperture than a Ø1/2 inch optic while the mount keeps a Ø1 inch footprint. Ø25.4 mm is the general-purpose size that fits the widest range of mounts. If your system is built on Polaris, take the 19 mm blank; if it is a conventional optical bench, take this one.

Key Features

  • No coating at all: the reflectance of the finished optic is whatever you deposit, and no band is implied by the part number
  • Front face better than λ/10 at 632.8 nm with 10-5 scratch-dig: a better surface than the coated parts in the same size, because a coating can add scatter but cannot improve figure
  • 6.0 mm ±0.2 mm substrate-grade fused silica: thick enough to survive handling and coating, thin enough for standard one inch mounts
  • Rear face fine ground and laser engraved: the marking identifies the substrate after coating, when the front face is no longer readable
  • Ø25.4 mm with a 90 percent clear aperture: the size that fits the largest number of mounts without an adapter
  • λ/20 figure available as a custom order: for interferometry and reference surfaces where λ/10 is the limiting term
  • Volume pricing available: blanks are the usual way to buy substrate for a coating run of several parts

Technical Specifications

Model PF10-03
Type Uncoated plano mirror blank
Material Fused silica, substrate grade
Coating None
Diameter Ø25.4 mm (1 in)
Diameter tolerance +0.0 mm / -0.1 mm
Thickness 6.0 mm (0.24 in)
Thickness tolerance ±0.2 mm
Front surface flatness Better than λ/10 at 632.8 nm; λ/20 available as a custom order
Front surface quality 10-5 scratch-dig
Clear aperture 90 percent of the diameter
Rear surface Fine ground, engraved with the item number
Parallelism Not published in the current blank series table
Transmission range 185 nm – 2.1 µm, uncoated substrate
Typical mounts Ø1 in kinematic and fixed optic mounts (KM100 and LMR1 class)
Source Thorlabs official series specification table

Applications

  • Custom coating: send the blank to a coating house, or coat it in house, with a design that no stock mirror offers
  • Prototyping: hold the geometry with a blank while the coating specification is still being argued about, then coat when the design freezes
  • Recoating a damaged optic: if the film failed but the substrate survived, a strip and recoat is cheaper than a new finished mirror
  • Figure reference: a bare substrate can be put on a interferometer to verify the surface without a film adding phase
  • Teaching and process development: deposition trials, cleaning trials and handling training all destroy optics, and a blank is the least expensive thing to destroy

Selection Guide

Item Diameter Thickness When to choose it
PF05-03 Ø12.7 mm (0.5 in) 6.0 mm Tight packaging, small beams, Ø1/2 in mount already in the design
PF07-03 Ø19.0 mm 6.0 mm Polaris fixed mounts, OEM laser heads, more clear aperture in a Ø1 in footprint
PF10-03 Ø25.4 mm (1 in) 6.0 mm General optical benches, the widest mount ecosystem, the default choice
PF20-03 Ø50.8 mm (2 in) 12.0 mm Large beams, converging paths, imaging folds

Series Comparison

Property Fused silica (this blank) Zerodur blank N-BK7 substrate
Expansion coefficient About 0.55 x 10⁻⁶ per °C 0 ± 0.100 x 10⁻⁶ per °C About 7.1 x 10⁻⁶ per °C
Useful transmission 185 nm – 2.1 µm Visible to near infrared About 350 nm – 2 µm
Figure stability under thermal cycling Good Best available Poor
Bulk homogeneity Excellent Excellent Good
Relative cost Moderate Highest Lowest
Where it belongs General laboratory work Interferometry, high power, space, thermal transients Cost-driven visible systems

FAQ

Q: Can I have this coated by a third party?

A: Yes, and that is the normal use. Tell the coater the substrate is fused silica, the figure is better than λ/10, the surface is 10-5 and the rear face is fine ground. Ask them to state the figure after coating, because deposition stress can move it, and ask what cleaning the process requires so the surface survives the pre-coat step.

Q: Which face is meant to be coated?

A: The front, the face held to λ/10. Thorlabs designs these blanks as front-surface mirrors, and the rear face is deliberately left fine ground so that it scatters rather than forms a second image. Coating the ground face would be a waste of a coating run.

Q: Why is there no reflectance value on this page?

A: Because the part has no film. Bare silica reflects by Fresnel reflection at each interface, and that is a property of the material and the angle, not of this part number; there is no specified band and no average to quote. Any reflectance you see for a finished mirror belongs to its coating, not to the substrate.

Q: Is 10-5 realistic for an uncoated blank?

A: Yes. A blank is polished to the same grade as, or better than, the coated parts made from it, because coating adds scatter and cannot smooth a surface. The 10-5 figure is what makes the blank usable as a coating substrate for imaging and interferometry rather than only for beam dumps.

Q: Fused silica or Zerodur?

A: Compare the expansion numbers and the temperature swing. A laboratory bench that holds within a degree or two does not need Zerodur, and fused silica also transmits further into the ultraviolet. If the optic must hold figure through cycling, sits in a high-average-power cavity, or flies, pay for Zerodur. A Zerodur blank in a smaller size is listed separately if you want to compare the two substrates directly.

Q: Is the rear face parallel to the front?

A: The current blank series table does not publish a parallelism figure for this item, so we do not quote one. If parallelism matters for your layout, for example because the rear reflection must go somewhere specific, ask for it to be measured on the delivered part rather than assumed.

Usage Precautions

  • Handle by the edge with gloves. A 10-5 surface shows every fingerprint, and cleaning it back to 10-5 is harder than not touching it.
  • Treat the rear face as non-optical. It is fine ground by design and will scatter anything that reaches it; do not polish it and do not expect an image through the part.
  • Clean before coating, not after. Any residue left on the front face is buried under the film, and the failure appears later as a pinhole or a delamination.
  • Store dry and separated. Blanks stacked face to face scratch each other, and the scratch is on the surface you paid to have figured.

Disclaimer

Figures reproduced here come from public manufacturer documentation and are intended as a selection aid, not as a substitute for the released drawing. Where a value is not published we say so rather than estimate it. Commercial terms are confirmed in writing before shipment.

Contact Us

Tell us the working wavelength, the clear aperture you need and how the optic will be mounted, and we will confirm the part, the coating and the expected delivery in one reply. Requests for matched sets, coating certificates or incoming inspection data are handled by the same desk.

Reviews

There are no reviews yet.

Be the first to review “Thorlabs PF10-03 Fused Silica Mirror Blank, Ø25.4 mm (1 in), 6.0 mm Thick”

Your email address will not be published. Required fields are marked *

中文EN