Description
This is the 10-piece pack of the PF10-03-M02; the optic is identical to the single-unit version.
Product Overview
Ten discs, each Ø25.4 mm of fused silica, 6.0 mm thick within plus or minus 0.2 mm, coated with dielectric-enhanced gold at 98 percent average and 95 percent absolute reflectance from 2 µm to 20 µm over 0 to 45 degrees of incidence. Front face λ/10 at 633 nm, 40-20 scratch-dig, parallelism 3 arcmin or better, clear aperture 90 percent of the diameter at Ø22.9 mm. The rear faces are fine ground and laser engraved with the item number, which is how you still know what a disc is after it has been out of its bag for a month.
A carbon dioxide cutting or marking machine almost never has one fold mirror. Beam paths of four, six or eight turning points are ordinary, and every one of them sits between the resonator and the workpiece. When those points are populated from different purchases made months apart, the reflectance at each point differs by whatever the coating run and the storage history happened to give. The result is a power budget nobody can close, because total throughput is the product of all the reflections: eight mirrors at 98 percent leave 85 percent, and one weak mirror at 94 percent pulls the whole chain down with it.
One pack removes that variable at the purchasing stage rather than at the troubleshooting stage. Ten optics ordered together normally come from the same coating run, are packed together, ship together and are stored together, so the spread between fold points is a specification spread rather than an unknown. When a mirror is replaced from the same pack, the machine does not need to be re-characterised; when it is replaced from a box bought two years later, it does.
What the pack does not do is remove the need for a first-article measurement. Ten parts meet one specification, and a specification is a window: 98 percent is an average, and the absolute floor is 95 percent. Measure one optic on the power meter at the working wavelength, record it, and use that as the reference for the whole set. That single number is worth more during a fault-find than any datasheet curve.
Key Features
- One coating lot for the whole beam path: every turning point populated from the same order, so per-station reflectance differences stop being a variable in the power budget
- Pack size of ten: enough for a six to eight fold carbon dioxide gantry plus two held back as line-side spares
- 98 percent average, 95 percent absolute: the highest reflectance available in this format between 2 and 20 µm, with a guaranteed floor rather than only a mean
- 0 to 45 degrees: the specification covers the fold angle these mirrors are actually used at, not just normal incidence
- 450 W/cm continuous at 10.6 µm: the rating that belongs to the working wavelength of a carbon dioxide line
- Engraved item number on every rear face: sorting ten discs across a bench does not turn them into anonymous gold blanks
- λ/10 at 633 nm, 40-20 scratch-dig: consistent wavefront across all ten, which is what makes a batch usable as a set rather than as ten individuals
- Standard Ø1 inch format: fits the mounts, the kinematic stages and the retaining rings already on the machine
Technical Specifications
| Model | PF10-03-M02-10 |
| Pack quantity | 10 optics per box |
| Coating designation | MIR-enhanced gold |
| Angle of incidence | 0 – 45 degrees |
| Working band | 2 – 20 µm |
| Average reflectance | Ravg 98 percent |
| Absolute reflectance | Rabs 95 percent minimum |
| Substrate material | Fused silica |
| Thickness | 6.0 mm |
| Thickness tolerance | plus or minus 0.2 mm |
| Diameter | Ø25.4 mm per optic |
| Diameter tolerance | +0.0 mm / -0.1 mm |
| Surface flatness | λ/10 at 633 nm (PV) |
| Surface quality | 40-20 (scratch-dig) |
| Clear aperture | 90 percent of diameter, Ø22.9 mm |
| Parallelism | 3 arcmin max |
| Rear face | Fine ground, item number engraved |
| Damage threshold, 10.6 µm, pulsed | 3 J/cm² (100 ns, 1 Hz, Ø1.29 mm) |
| Damage threshold, 10.6 µm, CW | 450 W/cm (Ø1.18 mm) |
| Damage threshold, 1.064 µm, pulsed | 0.1 J/cm² (10 ns, 10 Hz, Ø1.06 mm) |
| Damage threshold, 1.07 µm, CW | 25 W/cm (Ø1.04 mm) |
| Data source | Manufacturer published series tables |
Applications
- Multi-fold carbon dioxide gantries: a single pack populates every turning point between the resonator and the cutting head with one coating lot
- Galvanometer head entry paths: the two or three folds upstream of the scan head, where a consistent input power keeps the marking recipe valid across machines
- Line-side spare cabinets: a sealed pack next to the machine turns a mirror replacement into a ten-minute job instead of a purchase requisition
- Retrofit and upgrade kits: when an old beam path is rebuilt, the folds are usually the cheapest part to renew and the most likely to be the cause of a power shortfall
- OEM machine builds: kitting ten per machine removes a per-machine purchase order and a per-machine incoming inspection
- Preventive maintenance cycles: planned replacement of the whole fold set at a fixed interval, rather than reactive replacement of whichever mirror failed first
Selection Guide
Within a mid-infrared line the question is not which coating, it is which station gets which duty. The table maps the usual stations to what the optic actually has to survive, which is what determines whether a pack of ten is the right holding.
| Station in the beam path | Duty at the optic | What the pack fixes |
|---|---|---|
| Resonator output fold | Full power, largest beam, least forgiving | Uniform first reflection, so downstream losses are predictable |
| Beam-expander folds | Moderate power, small beam, tight alignment | Same wavefront at both folds, so the expander stays collimated |
| Gantry traverse folds | Moving axis, vibration, occasional clipping | Identical spare available without re-measuring the path |
| Scan head entry fold | Small beam, high energy density | Known reflectance, so the marking recipe transfers between machines |
| Final focusing fold | Highest energy density in the path | A matched replacement when the coating finally gives up |
For a path with fewer than three turning points, a single PF10-03-M02 plus one spare is usually the better buy. The pack pays from about four folds upward, which is where most carbon dioxide cutting and marking machines sit.
Series Comparison
The same ten-piece logic applies across the metal coatings. The comparison below is about what a production buyer needs to know: band, whether the film can be cleaned, and whether ten from one box behaves like a set.
| Pack item | Band | Ravg | Cleanable | Best use of a ten-pack |
|---|---|---|---|---|
| PF10-03-M01-10 | 800 nm – 20 µm | 96% | Yes | Mixed-wavelength shops and fibre laser folds |
| PF10-03-M02-10 | 2 – 20 µm | 98% | Yes | Carbon dioxide lines with four or more folds |
| PF10-03-M03-10 | 800 nm – 20 µm | 97% | No | Polarization-sensitive paths run as sealed consumables |
| PF10-03-P01-10 | 450 nm – 20 µm | 97% / 95% | Yes | Visible and near-infrared paths that need the highest reflectance |
| PF10-03-G01-10 | 450 nm – 20 µm | 90% / 95% | Yes | General workshop paths where cost dominates |
FAQ
Q: Do the ten come from the same coating run?
A: Normally yes, because a pack is picked and packed as one unit, but it is not a contractual guarantee and no manufacturer promises it. What you can rely on is that all ten meet the same specification window and have shared the same storage and shipping history. Measure one at the working wavelength and treat that as the reference for the set.
Q: Do I have to recalibrate the machine after replacing a fold mirror from the pack?
A: Check the power at the workpiece, not the whole recipe. If the replacement came from the same pack and measures within a fraction of a percent of the optic it replaced, the process does not need touching. If the reading moves by more than a percent, find out why before adjusting anything: it is usually contamination somewhere else in the path, not the new mirror.
Q: Can I mix a pack and single units on one machine?
A: You can, but keep a record. Singles bought later may come from a different run, and the difference will show up as one station reading slightly low forever. Label the mounts with purchase batch and install date; that label is the only thing that will let you interpret a slow power drift six months from now.
Q: How should ten mid-infrared mirrors be stored on site?
A: In the original slotted case, closed, dry, and off the floor. Never face to face. Let the case come to room temperature before opening it in a humid area, otherwise condensation lands on the coating and leaves a haze that no wipe will fully remove.
Q: Is there any point buying ten if I only have three fold points?
A: Only as a two-year consumable holding. Below four folds the arithmetic favours singles plus one spare, unless the machine is in a dirty process where contamination events are frequent, in which case the pack is a downtime decision rather than a cost decision.
Q: Why not just buy the cheapest ten mirrors that fit the mount?
A: Because a carbon dioxide path multiplies losses. Eight folds at 98 percent leave 85 percent at the workpiece; eight at 94 percent leave 61 percent, and the difference is paid for in cutting speed every hour of every shift. The pack is the cheap part of that equation.
Usage Precautions
- Label every fold point before removing anything: position number, install date, and which pack the optic came from. Ten identical discs become untraceable the moment they leave the case.
- Replace one mirror at a time and measure the workpiece power after each swap. Changing four optics at once and then finding a shortfall leaves you with no way to tell which one caused it.
- Keep the 2 µm boundary in mind for the whole path, not just for one fold. A visible pilot laser routed through any of these ten will not behave predictably.
- Do not substitute a protected gold mirror at one station because it was what came to hand. The reflectance difference between 96 and 98 percent is small per mirror and significant across eight of them.
- Clean only when the power reading justifies it, and then blow before wiping. A dielectric stack wiped on a schedule rather than on evidence loses years of life for no benefit.
- Use plastic-tipped retaining rings and tighten only until the disc stops moving. A bent 6 mm disc no longer holds λ/10, and a bent disc in a batch is the one that reads low.
- Store the unopened remainder sealed. A pack that lives open on a machine frame is a pack that collects the workshop before it is used.
Disclaimer
Specifications here are compiled from the manufacturer published series tables and are offered for selection purposes only; the current official datasheet governs. Coatings, dimensions and markings may change without notice. Price and delivery are quoted separately by our sales desk.
Contact Us
Tell us how many turning points the machine has, the working wavelength, the beam diameter at each fold and the total power, and we will size the holding for you and flag any station where the M02 coating is the wrong choice. Project and OEM quantities are quoted individually.









Reviews
There are no reviews yet.