QQ: 859818709

Thorlabs PF1011-G01 Ø25.4 mm (1 in) Zerodur® Protected Aluminum Mirror, 450 nm – 20 µm

Thorlabs PF1011-G01 Ø25.4 mm (1 in) Zerodur® Protected Aluminum Mirror, 450 nm – 20 µm

Price on request
Category:

Description

Product Overview

The PF1011-G01 is a 25.4 mm (1 inch) Zerodur® disc carrying protected aluminum: an aluminum film with a silicon dioxide overcoat, specified at 90% average reflectance from 450 nm to 2 µm and 95% average reflectance from 2 µm to 20 µm. The disc is 6.0 mm (0.24 in) thick to within plus or minus 0.2 mm, figured to lambda/10 peak to valley at 632.8 nm, polished to 40-20 scratch-dig, parallel to within 3 arcmin, and specified with a clear aperture of 90% of the diameter, which on a 25.4 mm part is Ø22.9 mm. The back face is fine ground and carries the item number. Zerodur® is a registered trademark of Schott; the material is Schott glass-ceramic bought by Thorlabs in substrate grade, with a coefficient of thermal expansion of 0 plus or minus 0.100 x 10-6/°C against 0.55 x 10-6/°C for fused silica.

The argument for aluminum over the three other metals Thorlabs offers on this identical body is coverage, and coverage is easiest to see as an absence. Protected silver is specified at 97% from 450 nm to 2 µm but only 95% beyond 2 µm and has no rating below 450 nm. Both gold coatings start at 800 nm, so everything blue, green and red is simply outside their specification. Aluminum is the one film of the four that runs from 450 nm to 20 µm without a dead band anywhere in the middle, which is why it is still the default broadband metal coating after decades of dielectric stacks.

That property becomes a design decision the moment a beam path carries more than one wavelength. A typical bench has a 632.8 nm helium-neon alignment beam, a 1064 nm or 1070 nm working beam, and a 3 to 5 µm probe or a 10.6 µm CO2 line sharing the same steering mirrors. Put protected silver in that path and the alignment beam is fine while the 10.6 µm leg runs 5 points down and degrades further with every month of tarnish. Put protected gold in it and the red alignment beam is not reflected usefully at all, so you cannot see where the beam is going. With the -G01 the alignment beam, the working beam and the probe all reflect off the same surface at the same point, which also means the alignment beam is guaranteed coaxial with the power beam instead of merely close to it.

The price of that breadth is paid in the visible. Ninety percent average reflectance means one reflection removes a tenth of the beam and four reflections leave 65.6% of it, against 88.5% for the protected silver version – a gap of 22.9 percentage points across a four-mirror relay. If the visible budget is tight and the band stops at 2 µm, silver is the correct choice and this page is the wrong one. If the band has to reach 20 µm, aluminum is the only one of the four that can do the job at all.

The second half of the case is environmental. The SiO2 overcoat is the most established barrier in the Thorlabs metal coating set: it keeps the aluminum from oxidising, it is hard enough to survive a solvent drag wipe, and Thorlabs states that its protected aluminum has a smaller chance of tarnishing than protected silver in a high humidity environment. On a bench in a climate-controlled laboratory that distinction is academic; in a workshop where the roller door opens onto a loading bay, or on a machine that is cleaned down with an alcohol spray every Friday, it is the difference between an optic that lasts years and one that hazes in a season.

Two boundaries should be stated plainly. Below 450 nm this coating is out of band: the aluminum plasma edge sits in the deep ultraviolet and a UV-enhanced aluminum film is the part for 250 to 450 nm work. And 90% in the visible is a real loss, not a rounding error – at 10 W through four folds roughly 3.4 W ends up as heat in the mounts, which is why the low-expansion substrate is not decorative even on a coating chosen for convenience.

Key Features

  • Continuous 450 nm to 20 µm band: 90% average from 450 nm to 2 µm and 95% average from 2 µm to 20 µm, with no unusable segment between the two ranges
  • Zerodur® glass-ceramic body: 0 plus or minus 0.100 x 10-6/°C, so a warm room moves the surface about five times less than a fused silica disc of the same size
  • Silicon dioxide overcoat: a hard, cleanable barrier over a metal that would otherwise oxidise and mark at the first touch, and the coating Thorlabs rates as less prone to tarnishing in high humidity than protected silver
  • 25.4 mm format: fits the standard 1 inch mirror mounts and kinematic holders used across most beam-delivery hardware, with Ø22.9 mm of clear aperture for beams up to about 15 mm
  • Lambda/10 figure, 40-20 polish: peak to valley at 632.8 nm on the front face, 3 arcmin parallelism, fine-ground back to suppress back reflections
  • Documented laser ratings: 0.5 J/cm2 pulsed at 1064 nm and 500 W/cm continuous at 1.07 µm for this coating, published by Thorlabs at coating level

Technical Specifications

Parameter Value
Item Number PF1011-G01
Coating Protected Aluminum (aluminum film plus SiO2 overcoat)
Wavelength Range 450 nm to 20 µm
Average Reflectance 90% from 450 nm to 2 µm; 95% from 2 µm to 20 µm
Substrate Zerodur® glass-ceramic (registered trademark of Schott), substrate grade
Diameter 25.4 mm (1 in), +0.0 / -0.1 mm
Thickness 6.0 mm (0.24 in), plus or minus 0.2 mm
Clear Aperture 90% of the diameter, Ø22.9 mm
Front Surface Flatness lambda/10 peak to valley at 632.8 nm
Surface Quality 40-20 scratch-dig
Parallelism 3 arcmin maximum
Coefficient of Thermal Expansion 0 plus or minus 0.100 x 10-6/°C (fused silica for comparison: 0.55 x 10-6/°C)
Back Surface Fine ground, item number engraved
Pulsed Damage Threshold 0.5 J/cm2 at 1.064 µm, 10 ns, 10 Hz, over a 1.000 mm beam
CW Damage Threshold 500 W/cm at 1.07 µm
Mounting Interface 25.4 mm outside diameter, edge-clamped in a standard 1 inch mount

The 40-20 scratch-dig figure above is the specification for a coated surface, and it is worth stating because 10-5 is often quoted for this part number. Ten-five belongs to the uncoated Zerodur blank; once a metal film and an overcoat are deposited, the finished optic is specified at 40-20. Anyone comparing a 10-5 claim against a 40-20 datasheet is comparing a blank with a mirror.

On the two damage rows: 0.5 J/cm2 over a 1.000 mm spot is 3.9 mJ per pulse, which is the number to hold against your own pulse energy after you have allowed for the actual spot size at the mirror. The continuous rating of 500 W/cm is a linear figure – power divided by beam diameter – so a 1 mm beam carries 50 W and a 5 mm beam carries 250 W before the coating is at its published limit. Both are coating-level ratings on a test bench, not a warranty for your cavity.

Applications

  • Multi-wavelength steering on one mirror set: visible alignment, near-infrared working beam and mid-infrared probe sharing the same fold mirrors, so all three are coaxial by construction
  • Humid or lightly serviced environments: unheated workshops, water-cooled machine frames and enclosures where condensation cycles would attack a silver film
  • Mid-infrared benches with a visible pilot: FTIR accessory optics, gas-sensing cells and thermal-imaging boresight paths that need the red beam to be visible and the 3 to 12 µm beam to be reflected
  • Teaching and alignment benches: a single part number that works with a helium-neon, a diode and a CO2 tube removes an entire category of wrong-part mistakes
  • OEM instruments with mixed inventories: one coating across a product family instead of three, which simplifies spares, documentation and incoming inspection

Selection Guide

Answer these five questions in order. The first one that fails removes this part from the shortlist.

  1. Does the band start at or above 450 nm and end at or below 20 µm? Anything below 450 nm needs UV-enhanced aluminum instead; nothing in this family covers the ultraviolet.
  2. Does the path carry more than one wavelength? If yes, aluminum is usually the only film that covers all of them, and that alone decides the order.
  3. Is the environment damp, dusty or cleaned aggressively? A protected aluminum film tolerates both better than protected silver; the overcoat is the reason.
  4. Can the link budget absorb 10% per reflection? Four folds cost 34.4%. If that is too much and the band stops at 2 µm, move to protected silver.
  5. Is the beam inside Ø22.9 mm? Keep the beam to roughly 15 mm or less so that pointing drift and edge roll-off never bring the rim into the beam.

Series Comparison

All four coatings below are deposited on the same PF1011 Zerodur® body: 25.4 mm diameter, 6.0 mm thick, lambda/10 figure, 40-20 polish, 3 arcmin parallelism, 90% clear aperture. Only the film changes, so the mechanical envelope and the mount interface are identical across the family.

Coating Wavelength Range Average Reflectance Where It Wins
-G01 Protected Aluminum 450 nm to 20 µm 90% / 95% Widest band with no gap, best humidity tolerance, cleanable
-M01 Protected Gold 800 nm to 20 µm 96% Flat infrared response, cleanable, CO2 and 1 µm power folding
-M03 Unprotected Gold 800 nm to 20 µm 97% Ultrafast pulses and strict polarization purity, no overcoat
-P01 Protected Silver 450 nm to 20 µm 97% / 95% Highest visible and near-infrared efficiency, cleanable

Read the table as a set of trades rather than a ranking. Silver is the brightest in the visible but falls to 95% above 2 µm and is the more delicate film. Gold is the brightest in the infrared but blind below 800 nm. Aluminum gives up seven points in the visible to be usable everywhere and to survive a damp room. The correct answer is whichever trade your beam path can afford.

FAQ

Is 90% average reflectance enough for a real system?

It depends entirely on how many reflections you have and how much margin the source gives you. One fold at 90% is a 10% loss, which most laser processes absorb without noticing. Four folds leave 65.6%, which is a 34% loss and does start to matter for a marking process running at the edge of its window. Count the folds before you count the percent.

Why is the visible figure lower than protected silver?

Aluminum has a plasma edge in the deep ultraviolet and its reflectance climbs gradually through the visible, while silver is already near its peak at 450 nm. Thorlabs specifies the aluminum film at 90% average over 450 nm to 2 µm and silver at 97% over the same range. The seven points buy a continuous curve out to 20 µm and a film that tolerates humidity; they are not free.

Can I clean this mirror with solvent?

Yes, and that is the main practical difference between this coating and the bare gold version. Blow off loose dust first, then drag a lens tissue wet with reagent-grade solvent once across the surface in one direction and stop. Never dry-rub a surface that may carry grit, and never scrub a coating to remove a mark that has already been there for a month.

Does the substrate really matter on a 25 mm mirror?

It matters more than on a small optic, because a 25.4 mm disc absorbs four times the power of a 12.7 mm disc at the same irradiance. Zerodur at 0 plus or minus 0.100 x 10-6/°C removes the substrate term from the drift budget; the mount and the coating stress remain, so a Zerodur mirror in a badly designed holder still moves.

Will a 632.8 nm alignment laser work through this coating?

Yes, at about 90%, which is bright enough for any alignment camera or screen. That is exactly the point of the coating: the same surface that carries the 1064 nm or 10.6 µm beam also carries the visible pilot, so there is no separate alignment optic and no parallax between the two paths.

Usage Precautions

  • Handle by the rim: gloves or finger cots, never the coated face. A fingerprint is a localised absorber and, at power, a localised failure point.
  • Clean wet, once: blow, then one wet drag wipe, then stop. Repeated wiping of the same spot polishes the overcoat thinner and shows up later as a reflectance dip.
  • Do not over-clamp: a retaining ring tightened until the optic stops moving is already enough to bend a 6 mm disc and print astigmatism into the reflected wavefront.
  • Keep the beam inside the clear aperture: 90% of 25.4 mm is Ø22.9 mm, and the outer rim is where edge scatter and figure roll-off live.
  • Budget the 10%: at 100 W through four folds roughly 34 W becomes heat in the mirrors and mounts. That heat is what the low-expansion substrate is there to survive, not to ignore.
  • Store dry: the overcoat slows oxidation, it does not seal the part. Long-term storage belongs in a desiccator or the original packaging, not on an open shelf.

Disclaimer

Specifications on this page are transcribed from Thorlabs official public documentation and are provided for selection reference only; the current official specification sheet governs. Thorlabs may change coatings, tolerances and appearance without notice. Reflectance values are averages over the stated ranges and individual witness runs vary within the coating specification. Prices, stock and delivery times are confirmed by our sales team at the time of order, and nothing on this page is a binding offer.

Contact Us

Gaofei Laser supplies genuine Thorlabs stock and quotes this item with current availability, lead time and volume pricing. Send the item number, the quantity and the wavelengths in your path, and we will confirm the coating choice and the mount interface before you order.

  • Sales hotline: +86 159 2722 0467
  • Email: 859818709@qq.com
  • Website: www.soar-laser.cn
  • Company: Gaofei Laser, soar-laser.cn

Reviews

There are no reviews yet.

Be the first to review “Thorlabs PF1011-G01 Ø25.4 mm (1 in) Zerodur® Protected Aluminum Mirror, 450 nm – 20 µm”

Your email address will not be published. Required fields are marked *

中文EN