QQ: 859818709

Thorlabs PF1011-M03 Ø25.4 mm (1 in) Zerodur® Unprotected Gold Mirror, 800 nm – 20 µm

Thorlabs PF1011-M03 Ø25.4 mm (1 in) Zerodur® Unprotected Gold Mirror, 800 nm – 20 µm

Price on request
Category:

Description

Product Overview

The PF1011-M03 is bare gold on a 25.4 mm (1 inch) Zerodur® disc: a gold film with nothing deposited on top of it, specified at 97% average reflectance from 800 nm to 20 µm. Dimensions are 6.0 mm (0.24 in) thick to within plus or minus 0.2 mm, lambda/10 peak to valley at 632.8 nm, 40-20 scratch-dig, parallel to within 3 arcmin, clear aperture 90% of the diameter (Ø22.9 mm), with the item number engraved on the fine-ground back. Zerodur® is a registered trademark of Schott; the glass-ceramic is specified at 0 plus or minus 0.100 x 10-6/°C against 0.55 x 10-6/°C for fused silica.

This page is about a specific customer: the fold mirror inside a femtosecond or picosecond amplifier, where the pulse is short enough that the coating itself becomes part of the optical design. Two constraints apply that do not exist at nanosecond pulse lengths. The first is dispersion: a dielectric overcoat is a multilayer interference stack, and every layer adds phase that varies with wavelength, so a broadband pulse reflected from it comes out with group delay dispersion it did not have before. In a chirped-pulse amplifier that dispersion lands directly in the pulse compressor budget and can only be removed by adding more glass somewhere else. The second is polarization: the same interference structure treats s and p polarization differently, so a mirror that is fine for a linearly polarized nanosecond beam can rotate the ellipse of an ultrashort pulse train passing through several folds.

Bare gold removes both problems by removing the structure. Thorlabs puts it plainly: these mirrors can be used in applications where the polarization state needs to be strictly maintained, or to prevent dispersion due to the overcoat of protected gold mirrors. A metal reflects through its free electron response, which is smooth across the near and mid infrared and essentially free of the resonant features a stack introduces. That is the whole engineering case for a coating that is otherwise harder to own: 97% average reflectance from 800 nm to 20 µm: one point above protected gold on the same substrate, and matched in the 800 nm to 2 µm window only by protected silver, which cannot be used on an ultrashort path.

There is a simple way to see whether the overcoat matters in a given build, and it costs one autocorrelation trace. Measure the pulse at the output with the existing fold mirror in place, then substitute a bare gold mirror and measure again at the same power. If the pulse is broader or the compressor grating spacing has to move, the overcoat was contributing dispersion and every unit shipped will contribute the same amount. That reproducibility cuts both ways: a stack that is wrong for a 30 fs pulse is wrong for all of them, and a metal film that is neutral is neutral for all of them, which is why amplifier manufacturers specify bare metal folds rather than qualifying a coating batch by batch.

Zerodur® earns its place in this application for a different reason than on a CW cutting head. An amplifier output is not a steady thermal load – it is a high repetition rate train, tens of megahertz, that deposits a small amount of heat continuously for hours. That is the worst kind of load for a substrate with ordinary expansion: the temperature rise per pulse is negligible, the accumulated rise over a shift is not, and the result is a slow, monotonic wavefront drift that shows up as a changing focal spot rather than as a failure. A material with a coefficient of thermal expansion near zero turns that slow drift into nothing, which is worth more on a 25 mm optic than on a smaller one because the absorbed power scales with area.

The cost of having no overcoat is operational, and it is not a small cost. Gold does not oxidise and does not tarnish, so the film is chemically stable in a way that silver is not – but it is soft, and it is bare. A fingerprint is an absorber sitting on the reflecting surface. An aerosol droplet leaves a residue that cannot be removed. A single abrasive particle dragged across the surface leaves a scratch that scatters, and there is no protective layer to take the damage instead of the reflecting film. The handling rules further down this page are therefore not boilerplate; they are the operating condition of the part.

If the optic will be handled by a rotating cast of students or technicians, the protected gold -M01 on the same body is the pragmatic choice and the one point of reflectance is a fair price for a cleanable surface. If the mirror is going into a sealed amplifier box that nobody opens, -M03 is the better optic: brighter, dispersion free and polarization neutral.

Key Features

  • No dielectric overcoat: no added group delay dispersion and no unquantified polarization change, which is the reason this coating exists next to protected gold
  • 97% average from 800 nm to 20 µm: the joint-highest figure in the family over 800 nm to 2 µm, matched only by protected silver, and flat across the whole infrared band
  • Zerodur® body: 0 plus or minus 0.100 x 10-6/°C, so a multi-hour high-repetition-rate run does not walk the wavefront
  • Chemically inert film: gold does not oxidise or tarnish, so storage is simple and shelf life is limited only by mechanical damage
  • Lambda/10 figure, 40-20 polish, 3 arcmin parallelism: figure and finish specified on the same drawing as the coating, so the wavefront budget is known before the coating is applied
  • High infrared ratings: 4 J/cm2 pulsed at 10.6 µm and 1000 W/cm continuous at 10.6 µm, published by Thorlabs for the bare gold film

Technical Specifications

Parameter Value
Item Number PF1011-M03
Coating Unprotected Gold (bare gold film, no overcoat)
Wavelength Range 800 nm to 20 µm
Average Reflectance 97% from 800 nm to 20 µm
Substrate Zerodur® glass-ceramic (registered trademark of Schott)
Diameter 25.4 mm (1 in), +0.0 / -0.1 mm
Thickness 6.0 mm (0.24 in), plus or minus 0.2 mm
Clear Aperture 90% of the diameter, Ø22.9 mm
Front Surface Flatness lambda/10 peak to valley at 632.8 nm
Surface Quality 40-20 scratch-dig
Parallelism 3 arcmin maximum
Coefficient of Thermal Expansion 0 plus or minus 0.100 x 10-6/°C (fused silica for comparison: 0.55 x 10-6/°C)
Back Surface Fine ground, item number engraved
Pulsed Damage Threshold 4 J/cm2 at 10.6 µm, 100 ns, 1 Hz, over a 0.435 mm beam
CW Damage Threshold 1000 W/cm at 10.6 µm over a 1.18 mm beam
Dispersion and Polarization No overcoat contribution; the metal response is smooth across the band

The published ratings for bare gold are quoted at 10.6 µm, which is where Thorlabs characterises the film, and they are coating-level figures rather than a guarantee at 800 nm. Treat them as the reference point and validate at your own wavelength, pulse length and repetition rate: for an 800 nm femtosecond train the practical limit is usually fluence and surface condition rather than the published number.

The last row is the one that matters for this part and cannot be expressed as a number. A dielectric overcoat contributes dispersion that depends on the stack design and polarization behaviour that depends on angle; a bare metal film contributes the Fresnel phase of a single interface, which is smooth, slowly varying and identical for every unit shipped. That reproducibility is what makes a bare gold fold usable inside a dispersion-managed amplifier rather than merely acceptable.

Applications

  • Femtosecond amplifier fold mirrors: the stretcher, the regenerative amplifier cavity and the compressor input, where added dispersion from an overcoat would have to be paid back elsewhere
  • Picosecond industrial micro-machining sources: fold paths before the galvo head where pulse fidelity and stable polarization both affect the cut
  • Optical parametric amplifiers and white-light seeding: broadband beams that see the whole coating curve at once, so a flat metal response is worth more than a peaky one
  • Polarization-sensitive interferometry: paths where several folds in series would otherwise accumulate an unquantified polarization change
  • Difference-frequency and mid-infrared generation: 3 to 12 µm idler paths that need high reflectance and no overcoat absorption in the far infrared

Selection Guide

This coating is the right answer to a narrow question and the wrong answer to a broad one. Test it in this order.

  1. Are the pulses shorter than a few picoseconds? If yes, overcoat dispersion is a real term in the budget and bare gold is the default.
  2. Does the polarization state have to survive the fold? If yes, the overcoat on -M01 is disqualified by the manufacturer’s own statement, and -M03 is the only option in the family.
  3. Is every wavelength above 800 nm? Bare gold is blind in the visible; a red pilot beam will not steer off this surface.
  4. Will anyone touch the optic? If the mirror is not inside a sealed enclosure, plan for protected gold instead, or write the handling rules into the build procedure.
  5. Is the beam inside Ø22.9 mm? Ultrafast beams are often slightly larger than the diffraction limit suggests; keep the beam under about 15 mm so pointing drift never reaches the rim.

Series Comparison

Four coatings, one substrate: 25.4 mm diameter, 6.0 mm thick, lambda/10 figure, 40-20 polish, 3 arcmin parallelism, 90% clear aperture. The only question the table answers is which film suits the pulse.

Coating Wavelength Range Average Reflectance Where It Wins
-G01 Protected Aluminum 450 nm to 20 µm 90% / 95% Visible through far infrared, robust in humidity, cleanable
-M01 Protected Gold 800 nm to 20 µm 96% Infrared power folding where the optic must be cleaned
-M03 Unprotected Gold 800 nm to 20 µm 97% Ultrashort pulses and polarization purity, highest infrared reflectance
-P01 Protected Silver 450 nm to 20 µm 97% / 95% Visible and near-infrared throughput, cleanable

The distance between -M01 and -M03 is one percentage point of reflectance and one overcoat, and it is the overcoat that decides the application. On a nanosecond cutting machine the layer is worth having because it lets the optic be wiped. Inside a femtosecond amplifier the same layer is a dispersion term and a polarization unknown, which is why both parts exist on one drawing rather than one part being declared better than the other.

FAQ

Why would anyone choose a coating that cannot be cleaned?

Because the alternative changes the pulse. In an ultrashort path the coating is not a passive layer, it is part of the dispersion budget, and a mirror that cannot be wiped is a smaller problem than a pulse that cannot be compressed. The usual arrangement is bare gold inside the sealed amplifier box and protected gold everywhere the beam is exposed.

Does bare gold oxidise or tarnish in air?

No. Gold is noble and does not form an oxide or a sulphide at room temperature, which is why this film survives storage far better than bare silver. The failure modes are mechanical and chemical contamination – fingerprints, aerosol residue, abrasive dust – not corrosion.

How do I clean it, then?

You do not, beyond blowing dust off with clean dry air or dry nitrogen. No solvent, no lens tissue, no polymer wipe, no adhesive tape, no ultrasonic bath. If a mark will not come off with a gas jet, the optic has to be replaced or sent for recoating; anything you do to it at that point will make the surface worse.

Is 97% really the best in this family?

In the 800 nm to 2 µm window, yes – one point above protected gold and equal to protected silver, but without the silver film’s sensitivity to humidity and without the overcoat. Across the full 450 nm to 20 µm range silver averages higher in the visible, where gold has no specification at all.

Can this mirror be used with a visible alignment laser?

Not usefully. Below 800 nm there is no reflectance specification for gold, and in practice the film reflects poorly enough in the red that alignment off it is unreliable. Infrared benches that need a visible pilot usually keep one protected aluminum or silver mirror in the path for that purpose.

Usage Precautions

These are the operating conditions of the part, not general advice. Bare gold has no sacrificial layer, so every one of the following is a hard rule.

  • Hold by the edge only: the rim, never the coated face, and always with latex gloves or finger cots. A fingerprint on bare gold is a permanent absorber.
  • Blow only: clean dry air or dry nitrogen is the sole permitted cleaning method. No acetone, no isopropanol, no lens tissue, no microfibre cloth, no swabs, no tape, no ultrasonic cleaning.
  • Plan the alignment before mounting: decide the incidence angle, the beam height and the polarization orientation on paper, because once the optic is in the holder you should not be touching the surface to adjust anything.
  • Keep aerosols and abrasives out of the enclosure: coolant mist, machining dust and aerosolised lubricant all settle on a horizontal mirror face, and none of them can be removed afterwards.
  • Do not over-clamp: a retaining ring snug enough to stop movement is enough. Over-clamping bends a 6 mm disc and prints astigmatism into the reflected wavefront, which on an ultrashort pulse is a spatial chirp you did not design.
  • Store face up in a dust-free container: the original packaging, or a covered petri dish. Never store it face down on any surface, and never stack optics.

Disclaimer

Specifications on this page are transcribed from Thorlabs official public documentation and are provided for selection reference only; the current official specification sheet governs. Thorlabs may change coatings, tolerances and appearance without notice. The bare gold film is specified without an overcoat; Thorlabs does not publish a dispersion or polarization figure for it, and any system-level dispersion budget should be measured rather than assumed. Prices, stock and delivery times are confirmed by our sales team at the time of order, and nothing on this page is a binding offer.

Contact Us

Gaofei Laser supplies genuine Thorlabs stock and can quote this item with current availability, lead time and volume pricing. Tell us the pulse length, repetition rate, fluence and polarization requirement and we will confirm whether bare gold or protected gold is the right film for your amplifier.

  • Sales hotline: +86 159 2722 0467
  • Email: 859818709@qq.com
  • Website: www.soar-laser.cn
  • Company: Gaofei Laser, soar-laser.cn

Reviews

There are no reviews yet.

Be the first to review “Thorlabs PF1011-M03 Ø25.4 mm (1 in) Zerodur® Unprotected Gold Mirror, 800 nm – 20 µm”

Your email address will not be published. Required fields are marked *

中文EN