Description
Product Overview
The PF125B is a stainless steel clamping fork for Ø1.85 in (Ø47.0 mm) pedestal bases, with a 1.25 in (31.8 mm) counterbored slot. It is a machined metal part, not an optic: it straddles a pedestal base, presses down on the flange with a single 1/4″-20 (M6) cap screw, and holds the base against the table without occupying the mounting holes around it. The slot is counterbored so the screw head sits below the top surface, and it is long enough to reach a table hole from either side of the base.
The reason this shape exists at all is what a fork does that a solid plate clamp cannot. A plate clamp covers an area of the table, presses on it everywhere, and leaves a witness mark; it also has to be positioned so its own screw hole lines up with a free tapped hole, which in a dense layout often means the hole you need is the one under the base you are trying to hold. A fork has two arms that pass either side of the base and a hollow centre, so it contacts the table at three points – the two arm ends and the region under the screw – and nothing else. The base is held by a downward load applied over its flange, the table surface between the arms is never touched, and the tapped holes immediately around the base stay available for the next component.
The three-point contact is also why the part is stable rather than merely tight. Three points define a plane whatever the table looks like locally, so the fork cannot rock on a surface that is flat to within its own tolerance. A four-point clamp on the same surface will rock by the amount of the table’s residual error and will transmit that rock into the base it is holding. On a breadboard with a few thousandth of an inch of flatness variation across a metre, that difference is measurable at the top of a 150 mm post.
The 360 degree rotation is the feature that saves time in practice. The fork is not keyed to the base: loosen the screw and the whole part rotates about the pedestal, so the slot can be swung to whichever tapped hole is closest rather than the base being moved to suit the fork. In a crowded layout, where moving a base means re-aiming everything downstream of it, being able to rotate the clamp instead is the difference between a five-minute change and an afternoon of realignment.
One warning belongs in the overview rather than at the bottom of the page, because it is the most common way this part is misused. Significant over-tightening will deform the surface of the optical table. A dented table is not a cosmetic problem: it lifts every component mounted over it, it destroys the flatness that the whole breadboard was bought for, and it cannot be repaired. The correct torque is the one that stops the base from moving, which is far less than most people apply by hand.
The PF125B is sold as a single unit. A five-piece pack, PF125B-P5, exists for labs that are clamping several bases at once; the fork itself is identical.
Key Features
- Fits Ø1.85 in (Ø47.0 mm) pedestal bases: the standard pedestal diameter used under post-mounted optics and small assemblies
- 1.25 in (31.8 mm) counterbored slot: enough travel to reach a tapped hole from either side of the base while keeping the screw head below the top surface
- Stainless steel: stiff enough that the clamp does not spring when the screw is tightened, and corrosion resistant in a lab atmosphere
- Three points of contact: two arm ends and the screw region only, so the fork sits flat without rocking and leaves the table between the arms untouched
- 360 degree rotation about the base: swing the slot to the nearest free hole instead of moving the base and re-aiming the optics above it
- 1/4″-20 (M6) cap screw: the counterbore takes the standard cap screw used across imperial and metric breadboards
Technical Specifications
| Parameter | Value |
|---|---|
| Item Number | PF125B |
| Type | Clamping fork for pedestal bases |
| Compatible Base | Ø1.85 in (Ø47.0 mm) pedestal bases |
| Counterbored Slot Length | 1.25 in (31.8 mm) |
| Material | Stainless steel |
| Contact Geometry | Three points of contact with the table surface |
| Fastener | 1/4″-20 (M6) cap screw through the counterbored slot |
| Rotation | 360 degrees about the pedestal base |
| Post Compatibility | Ø1.5 in post with PB4(/M) or PB4R(/M) base adapter; also Ø1 in post holder or BLP01 adjustable-height post |
| Packaging | Sold individually; PF125B-P5 is the five-piece pack |
| Family Slot Lengths | PF85B 0.85 in (21.6 mm); PF125B 1.25 in (31.8 mm); PF175B 2.12 in (53.8 mm) |
The fastener row deserves a note. The counterbore is sized for a standard socket-head cap screw, which is what you want here: a cap screw can be tightened with a ball driver from directly above, in a space too narrow for a wrench, and the counterbore keeps the head clear of anything passing over the clamp.
The compatibility row is often misread, so it is worth being explicit. The fork is sized for a Ø1.85 in pedestal base. Where the assembly sits on a Ø1.5 in post, the post needs a PB4(/M) or PB4R(/M) base adapter to present a base of the right diameter to the fork. Where the assembly sits on a Ø1 in post holder, or on a BLP01 adjustable-height post, the fork clamps the base of that holder directly. It is the base diameter that has to match, not the post diameter.
Applications
- Holding pedestal-mounted optics in place: mirror mounts, beamsplitter mounts and small assemblies that sit on a pedestal base and must not be knocked out of alignment
- Dense breadboard layouts: the hollow centre leaves the tapped holes around the base free, which is exactly where the next component wants to go
- Tables that must stay unmarked: three-point contact instead of full-surface clamping, for labs that care about the surface they paid for
- Layouts that change often: 360 degree rotation lets the slot find a hole instead of the base being relocated and the downstream path re-aimed
- OEM and instrument fixtures: a repeatable stainless part that can be specified into a build rather than improvised from a plate and a C-clamp
Selection Guide
The only real decisions are slot length and pack size; the base diameter decides whether this fork fits at all.
- Is the base Ø1.85 in (Ø47.0 mm)? If not, this is the wrong fork – the slot length does not compensate for a base of the wrong diameter.
- How much adjustment travel do you need? 0.85 in for compact layouts, 1.25 in for general work, 2.12 in where the base position is not yet fixed or the nearest hole is far away.
- Will the clamp be near other components? If space is tight, the shorter slot keeps the fork footprint small; if the layout is open, the longer slot costs nothing and buys margin.
- How many bases are being clamped? One fork per base; the five-piece pack is the same part in a larger box.
- What is the post below the base? Ø1.5 in post needs a PB4(/M) or PB4R(/M) adapter; Ø1 in post holders and the BLP01 clamp directly.
Series Comparison
Three forks share the same body, the same stainless steel and the same three-point contact geometry. Only the counterbored slot length changes, and the slot length is what decides where the screw can land.
| Item Number | Slot Length | Best For | Pack Option |
|---|---|---|---|
| PF85B | 0.85 in (21.6 mm) | Compact layouts where the base sits close to a tapped hole and space around it is tight | Single unit; five-piece pack available |
| PF125B | 1.25 in (31.8 mm) | General purpose: enough travel to reach a hole from either side of the base | Single unit; PF125B-P5 five-piece pack |
| PF175B | 2.12 in (53.8 mm) | Large adjustment margin, or layouts where the base position is not yet settled | Single unit; five-piece pack available |
The rule of thumb is that a slot that is too long costs nothing and a slot that is too short makes the part unusable, because the screw has to land in a real tapped hole. When the layout is still being developed, take the longer fork.
FAQ
Why a fork rather than a plate clamp?
A fork contacts the table at three points and leaves the middle open, so it does not print a mark on the surface and does not consume the tapped holes around the base. A plate clamp presses over an area and has to share its footprint with whatever else needs to be mounted there.
How tight should the screw be?
Tight enough that the base cannot be moved by hand, and no more. Significant over-tightening deforms the optical table surface, which raises every component mounted over that spot and permanently destroys local flatness. If you can see the table surface change under the arm, it is already too tight.
Which slot length should I order?
1.25 in covers most situations, because it reaches a tapped hole from either side of a Ø1.85 in base. Choose 0.85 in only when the surrounding layout is genuinely tight, and 2.12 in when the base position may still move or the nearest free hole is further away than usual.
Does it work with a metric table?
Yes. The counterbored slot takes a 1/4″-20 cap screw, and the M6 cap screw used on metric breadboards passes the same slot, so the same fork serves both hole patterns.
Can I rotate the fork after it is installed?
Yes, and that is one of its practical advantages. Loosen the screw and the whole fork turns about the pedestal base through 360 degrees, so the slot can be swung to whichever tapped hole is closest without moving the base or disturbing anything mounted above it.
What is the difference between PF125B and PF125B-P5?
Nothing except the quantity in the box. PF125B is one fork; PF125B-P5 is five identical forks. Buy the pack when several bases are being clamped in the same build, since the per-unit cost is lower and the parts are interchangeable.
Will it mark the table?
Three small contact patches instead of a full plate footprint, so any witness mark is minimal and local. Over-tightening is what turns a minimal mark into a dent, which is why the torque advice above matters more than the geometry.
Usage Precautions
- Do not over-tighten: significant over-tightening deforms the optical table surface, causing misalignment of the mounted component and a permanent loss of flatness where the arms contact. Stop as soon as the base stops moving.
- Check that the screw lands in a real hole: the slot is 1.25 in long, so it is easy to tighten against a position between holes. Confirm engagement before applying load.
- Keep the counterbore clear: swarf or a burr under the screw head means the clamp is held off the surface and the base is only partly loaded.
- Clean the table and the fork before mounting: grit trapped under an arm becomes a dent under load, and a dent in a breadboard is permanent.
- Rotate before tightening, not after: set the slot angle first, then tighten. Rotating a loaded fork drags the arms across the table surface.
- Use the right driver: a ball driver from above is the intended access, and a worn hex key will round the socket long before the clamp is tight enough to hold.
Disclaimer
Dimensions, materials and compatibility on this page are transcribed from Thorlabs official public documentation and are provided for selection reference only; the current official drawing governs. Thorlabs may change dimensions, materials and appearance without notice. Component compatibility depends on the base diameter and the post or adapter of the assembly being clamped, not on this page alone; confirm both before ordering. Prices, stock and delivery times are confirmed by our sales team at the time of order, and nothing on this page is a binding offer.
Contact Us
Gaofei Laser supplies genuine Thorlabs stock and quotes this item with current availability, lead time and volume pricing. Tell us the pedestal base diameter, the post or adapter in use and the number of clamps you need, and we will confirm the slot length and pack option before you order.
- Sales hotline: +86 159 2722 0467
- Email: 859818709@qq.com
- Website: www.soar-laser.cn
- Company: Gaofei Laser, soar-laser.cn









Reviews
There are no reviews yet.