Description
Product Overview
A counterbored slot is not decoration and it is not a manufacturing convenience. It is the part of a clamping fork that decides where the screw can physically land, and therefore how much error the clamp can absorb before the base has to be moved. Everything else about the PF175B is ordinary: a stainless body, three contact pads on the underside, one 1/4″-20 (M6) cap screw, and a fork mouth that straddles a pedestal base flange. The 2.12 in (53.8 mm) slot is what makes this the long version of the family rather than the short one.
Three separate problems are solved by slot length. First, a pedestal base is rarely exactly where the layout drawing puts it: the tapped hole grid on an optical table is on a 25 mm pitch, the base has one threaded centre, and the beam height and pointing that the design assumes may only be reachable with the base a few millimetres away from the nominal spot. The slot lets the screw find a hole without moving the base. Second, one fork has to serve several base spacings on the same bench, because a lab that keeps three slot lengths in a drawer will eventually fit the wrong one. A long slot covers more of the range with a single part number. Third, when the fork is rotated through its 360 degrees to clear a neighbouring mount, the screw no longer sits at the geometric centre of the fork mouth, and a long slot gives the screw somewhere to go at every angle.
The 53.8 mm slot is longer than the 47.0 mm flange diameter of the base it clamps. That has a practical reading: with the fork rotated, the screw can be placed at a radius of up to roughly half the slot length, about 27 mm, from the centre of the flange, which is more than the 23.5 mm flange radius. The fork therefore does not need the tapped hole to sit under the base at all. It can reach out to a hole beside the base, which is exactly the situation on a crowded table where the hole under the base is already occupied by the base thread itself.
The body is stainless steel. On a table whose surface is anodised aluminium over a much softer substrate, this is a deliberate hardness mismatch: the fork is the harder part and the table is the part that yields. That is the correct way round for a clamp, because a fork that deformed at the slot would lose its geometry and start to clamp at an angle, while a table that takes a small mark keeps its flatness everywhere else. It also means the fork survives years of tighten-and-loosen cycles without the slot walls galling or the thread pulling.
Underneath, the fork is relieved so that it touches the table at three points rather than over a full ring. Those three points define a plane. A four-point or full-ring contact on a real table, which is flat to a few micrometres at best and carries the scars of a decade of use, will rock on the highest point and leave the base held by whatever fraction of the ring happens to be loaded. Three points cannot rock. The clamp force goes into a predictable triangle, and the base stays put.
Thorlabs specifies the PB4(/M) and PB4R(/M) base adapters as the companions for this fork, and warns that significantly over-tightening the cap screw will deform the table surface, causing the mounted components to lose alignment and stability. That warning deserves more weight on the long version of the fork than on the short one, and the reason is mechanical rather than rhetorical: a longer bar is a longer lever.
Key Features
- 2.12 in (53.8 mm) counterbored slot. The longest of the three Thorlabs fork lengths for Ø1.85 in bases, giving the largest screw placement range and the most tolerance for a base that cannot sit where the drawing intended.
- Slot longer than the flange. At 53.8 mm against a 47.0 mm flange, the screw can land outside the base footprint entirely, so a tapped hole beside the base is usable.
- Stainless steel body. Harder than the anodised aluminium it bears on, so the slot and the thread hold their geometry and the table takes the wear instead.
- Three-point contact. The relieved underside loads three pads rather than a ring, which removes rocking on a table that is no longer perfectly flat.
- 1/4″-20 (M6) cap screw. The counterbore sinks the head below the fork surface so it cannot catch a cable or foul a neighbouring component.
- Full 360 degree rotation when loosened. Position the base, check the beam, then swing the fork to a clear direction and tighten once.
- Dimensioned for Ø1.85 in (Ø47.0 mm) pedestal bases. The intended pairing is the PB4(/M) or PB4R(/M) adapter named in the manufacturer specification.
- Supplied as a single fork. The right way to buy when one station needs to be proved out before a bench is standardised, or when a single base has to be added to an existing layout.
Technical Specifications
| Parameter | Specification |
|---|---|
| Model | PF175B |
| Component type | Clamping fork for pedestal bases |
| Base compatibility | Ø1.85 in (Ø47.0 mm) pedestal bases |
| Recommended base adapter | PB4(/M) or PB4R(/M) |
| Slot length | 2.12 in (53.8 mm) |
| Slot type | Counterbored slot |
| Screw interface | 1/4″-20 (M6) cap screw |
| Body material | Stainless steel |
| Contact geometry | Three-point contact with the table surface |
| Rotation when screw is loosened | 360 degrees |
| Screw placement radius, approximate | Up to 27 mm from the flange centre when rotated |
| Table compatibility | Imperial 1/4″-20 and metric M6 optical tables and breadboards |
| Quantity | One fork |
The screw placement radius is a geometric consequence of the slot length rather than a separately published dimension: half of 53.8 mm is 27 mm, and the fork can be rotated so that the screw lies anywhere along that slot. It is included because it is the number that answers the practical question, which is whether the fork can reach a particular tapped hole.
Applications
Bases that cannot sit on the nominal spot. The most common reason a fork is bought in the long version is that the layout has already been built and the base is not where the model says. A 25 mm tapped hole pitch, a base whose centre thread is offset from its flange centre, or a mirror mount that has to clear a beam dump all push the base off nominal. The long slot accepts that without drilling a new hole or redesigning the mount.
Rotated clamp directions on a crowded table. When the fork is turned 90 or 135 degrees to keep clear of a translation stage, the screw is no longer under the middle of the fork mouth. On the short fork this leaves very little slot left; on this one the screw still has tens of millimetres of travel in the new orientation. Crowded tables are where the long version earns its footprint.
Mixed base spacings on one bench. A bench that carries bases at 50 mm, 75 mm and 100 mm spacing can be clamped with a single part number if the slot is long enough. Standardising on one fork length removes the failure mode where a short fork is fitted to a widely spaced base and the screw head lands on the counterbore shoulder instead of seating.
Proving out a single station. When a new base family, a new table or a new mount is being evaluated, one fork is enough. Order one, fit it, check the stack height and the clamp behaviour, and only then decide what the rest of the bench needs. This is a real engineering argument for the single-unit part, and it is the reason the single version exists alongside the multi-unit pack.
Heavy or tall payloads on a single base. A tall post carrying a camera, a fibre launch or a large mirror mount puts a bending moment into the base, and a fork resists translation much better than it resists rotation. A longer slot does not by itself stiffen that joint; what it does is allow the clamp to be placed on whichever side of the base opposes the load, including the side where no tapped hole happens to sit under the base. Where the payload is genuinely heavy, the honest answer is a second clamp or a base with a larger footprint rather than a longer fork.
Retrofit into an existing frame. Where an optical sub-assembly arrives already built on a base and the task is to fix it to a new table, the long slot allows the fork to be positioned around whatever the sub-assembly already occupies.
Selection Guide
The three fork lengths differ only in slot length, so the decision is a single dimensional question: how far can the screw be from the base centre before the clamp stops working. The table below states that range for each model in the units that matter at the bench.
| Model | Slot length | Approximate screw reach from flange centre | Where it is the right answer |
|---|---|---|---|
| PF85B | 0.85 in (21.6 mm) | About 11 mm | Compact stacks, base close to nominal, neighbours within 25 mm |
| PF125B | 1.25 in (31.8 mm) | About 16 mm | General purpose, a few millimetres of placement error to absorb |
| PF175B | 2.12 in (53.8 mm) | About 27 mm | Base off nominal by more than 15 mm, rotated clamp directions, mixed spacings |
Two further checks complete the decision. Confirm the base family, because the fork is dimensioned for a Ø1.85 in (Ø47.0 mm) flange and the PB4(/M) or PB4R(/M) adapter, not for a generic 1.85 in footprint. Confirm the screw, because a 1/4″-20 cap screw is needed on an imperial table and an M6 cap screw on a metric one; the fork accepts either, but the counterbore is only deep enough for a screw of sensible length.
There is a cost to choosing the long version that should be stated rather than glossed over. The bar occupies 53.8 mm of slot plus its own body, so on a table where two bases sit 50 mm apart, two long forks will fight each other for the same table area. Where the bases are dense, the shorter fork is not a compromise but the correct part. The long version is for the cases where placement error or rotation angle is the dominant problem, and those cases are common enough that most laboratories end up keeping some of each.
Series Comparison
| Attribute | PF85B | PF125B | PF175B |
|---|---|---|---|
| Slot length | 0.85 in (21.6 mm) | 1.25 in (31.8 mm) | 2.12 in (53.8 mm) |
| Tier | Short | Middle | Long |
| Base compatibility | Ø1.85 in pedestal | Ø1.85 in pedestal | Ø1.85 in pedestal |
| Body material | Stainless steel | Stainless steel | Stainless steel |
| Contact geometry | Three-point | Three-point | Three-point |
| Screw | 1/4″-20 (M6) | 1/4″-20 (M6) | 1/4″-20 (M6) |
| Rotation when loosened | 360 degrees | 360 degrees | 360 degrees |
| Table footprint | Smallest | Moderate | Largest |
| Lever arm at the screw | Shortest | Moderate | Longest |
Because the three models share a body, a screw size and a contact geometry, the only attribute that changes materially is the lever arm. That is the row worth looking at twice: the same wrist force applied to the same screw produces a larger moment at the contact pads on the long fork, and the contact pads are what press into the table.
FAQ
Q: What does the slot length actually change?
A: It changes the range of positions in which the cap screw can be placed relative to the base. A longer slot lets the screw find a tapped hole that is further from the base centre, which is what makes the clamp work when the base cannot sit where the drawing intended, when the fork has to be rotated to clear other hardware, or when one fork has to serve several base spacings on the same bench.
Q: Why is the long fork more prone to marking the table?
A: Because it is a longer lever. The screw sits somewhere along a 53.8 mm slot and the contact pads sit at the far end of the bar, so the distance between the force and the reaction can be much larger than on the short version. The same hand force applied at the same wrench therefore produces a larger moment at the pads, and the pads are what press into the table surface. The manufacturer warning about over-tightening applies to the whole family, but it bites hardest here.
Q: Why does Thorlabs specify the PB4(/M) or PB4R(/M) adapter rather than a post series?
A: Because the fork clamps a flange and a post has no flange at table level. The PB4 family is a pedestal base with a flat circular flange sitting on the table; the fork straddles that flange and pulls it down onto three pads. A post or post holder is a vertical tube held by its own holder, so there is nothing for the fork to bear on and no three-point contact to develop. The fork will physically sit over a Ø1 in post holder, but the intended and dimensioned pairing is the base adapter.
Q: Does the fork really rotate a full turn?
A: Yes. Once the cap screw is loosened, the fork swings freely through 360 degrees about the screw axis. That is what allows the base to be positioned and the beam checked first, with the clamp direction chosen last. Tightening the screw locks the clamp force and the angular position together.
Q: Can I use it on an M6 table?
A: Yes. The fork accepts a 1/4″-20 or an M6 cap screw, so the same part works on either table standard. The screw changes; the fork does not. Use a screw short enough that the head sits down in the counterbore rather than standing proud.
Q: What if my base is not a Ø1.85 in pedestal base?
A: Then this is the wrong fork. The mouth is sized for a 47.0 mm flange, and a base of a different diameter will either not pass through the mouth or will sit loose in it, in which case the three-point contact no longer defines a stable plane. Measure the flange before ordering.
Q: Is one fork enough for one base?
A: One fork per base is the normal arrangement, and a single base with a light payload needs exactly one. A tall post carrying a heavy mount benefits from a second clamp or from a base with a larger footprint, because the fork resists translation well and rotation less well.
Q: Should I buy the long version for a whole bench?
A: Only if the bench actually needs the reach. Where bases are dense and placed accurately, the long bar wastes table area and interferes with its neighbours. Where bases are placed by eye, where the tapped hole under the base is occupied, or where clamps have to be rotated out of the way, the long version is the correct choice and the shorter ones will keep producing mis-clamped bases.
Usage Precautions
- Do not over-tighten, and be stricter about it on this model. The manufacturer states that significantly over-tightening deforms the table surface and degrades the alignment and stability of everything mounted on it. The deformation does not recover. On a long fork the lever arm magnifies the same hand force, so tighten until the base will not rotate by hand and stop there.
- Seat the head in the counterbore. If the head rests on the shoulder of the recess rather than dropping into it, the clamp will feel tight while applying little downward load. Move the base or change the fork length instead of forcing the screw.
- Keep the contact pads clean. A chip of swarf or a dried droplet under one of the three pads turns a three-point contact into a two-point contact plus a pivot. Wipe the underside and the table before fitting.
- Check the thread before the first installation. Run the cap screw in by hand. A stainless thread with a burr will gall on first use and the damage is permanent.
- Mind the footprint on dense tables. The bar plus its slot occupies more than 50 mm. Two long forks on bases 50 mm apart will not coexist; plan the clamp directions before drilling anything.
- Do not use it as a general-purpose clamp. The geometry is dimensioned for a Ø1.85 in pedestal flange. Holding a plate, a filter slide or a custom bracket puts load paths through the fork that the three pads were not placed for.
- Inspect after a drop. A fork that has fallen on a hard floor can have one ear slightly out of plane. A bent fork clamps at an angle and the base creeps. Compare it against a flat surface before returning it to service.
- Clean with solvent only. Isopropyl alcohol and a lint-free cloth. An abrasive will round the counterbore shoulder and change where the clamp force is applied.
Disclaimer
The dimensions and the mechanical behaviour described here follow the manufacturer published specification for the PF175B clamping fork. Drawings and tolerances on the current datasheet override this page, and the manufacturer may revise a specification without notice. Statements about how a clamp behaves on a particular table are engineering commentary, not a guarantee of performance in a specific assembly, and they assume a table in reasonable condition, a correct base adapter and a screw of appropriate length. No price is given here; price, lead time and stock are confirmed when an order or a quotation is prepared.
Contact Us
Send the base model, the table thread, the number of bases and, if it is known, how far the nearest usable tapped hole sits from the base centre. With those four facts the sales team can say whether the long fork will reach, whether the short one would do, and whether a second clamp is worth adding for a tall payload. Drawings, stack-height checks and quantity pricing for a mixed order of fork lengths are all handled through the same enquiry.









Reviews
There are no reviews yet.