Description
Product Overview
This is the 5-piece pack of the PF175B; each fork is identical to the single-unit version.
It is more useful to think of this pack as one line of a bill of materials than as five of a part. When an optical platform is built out, the clamps are never the item anybody plans: the table is chosen, the bases are counted, the mounts are specified, and the forks are whatever is left in the drawer on the day. That is how a build ends up with three different slot lengths on one table, two bases held by a fork that does not reach the tapped hole, and one station waiting two weeks for a low-cost part to arrive.
Reading the pack as a BOM line changes the order of the decisions. First the number of Ø1.85 in (Ø47.0 mm) pedestal bases is fixed by the optical layout, and that number, not the optical layout, determines the fork quantity. Second the slot length is fixed by how much placement error the table has to absorb, and the sensible answer is usually to pick one length for the whole platform rather than to optimise each station. Third the packaging is fixed by the quantity: once the count passes three or four, a pack is the sane unit of purchase, because the alternative is a series of small orders whose administrative cost exceeds the part cost.
The 2.12 in (53.8 mm) slot is the reason this particular pack works well as a platform-wide purchase. On a long slot, a base does not have to sit within a few millimetres of where the drawing puts it; the screw can be moved along the slot until it finds a tapped hole. That tolerance means one part number can serve stations with different base spacings, different mount footprints and different clamp directions. A platform stocked with a single fork model is a platform with a single line on the BOM, a single screw, a single wrench and a single tightening habit, and those four simplifications outlast any saving on the part itself.
Mechanically the fork is straightforward. The body is stainless steel, relieved on the underside so that it bears on the table at three points rather than over a ring, which is what stops it rocking on a surface that has seen a decade of use. A single 1/4″-20 (M6) cap screw pulls the base flange down; the counterbore sinks the head below the fork surface. Loosen the screw and the fork turns through 360 degrees, so the clamp direction can be chosen after the base is in position and the beam has been checked. Thorlabs names the PB4(/M) and PB4R(/M) base adapters as the intended companions, and warns that significant over-tightening will deform the table surface and degrade the alignment and stability of what is mounted on it.
All five forks in the pack are that same part. The pack is not an assortment, it is not a mixed set of slot lengths, and it should not be broken up into an unlabelled drawer.
Key Features
- Five identical PF175B forks. Same 2.12 in (53.8 mm) slot, same stainless body, same screw interface in every unit, so a pack can be issued to a platform without sorting it first.
- Pack size 5. Enough to fit out a platform of four or five bases and keep one float, which is the quantity most builds actually need.
- One SKU for a whole platform. The long slot absorbs differences in base spacing, so stations do not each need their own fork length.
- Stainless steel body. Holds its slot and thread geometry through repeated clamp cycles and does not shed coating debris at the contact points.
- Three-point contact. The relieved underside loads three pads, so the clamp cannot rock on a table that is no longer flat.
- 1.25 in and 0.85 in variants exist for dense layouts. This pack is the long-slot choice; the shorter forks remain the right answer where table area is tight.
- 1/4″-20 (M6) cap screw, counterbored. The head sits below the fork surface, clear of cables and neighbouring hardware.
- Full 360 degree rotation when loosened. Base first, beam second, clamp direction last, which is the order that works on a crowded table.
- PB4(/M) or PB4R(/M) base adapter. The pairing the fork was dimensioned around, with a 47.0 mm flange that matches the fork mouth.
Technical Specifications
| Parameter | Specification |
|---|---|
| Model | PF175B-P5 |
| Pack size | 5 forks |
| Pack content | Five identical PF175B forks, not a mixed assortment |
| Component type | Clamping fork for pedestal bases |
| Base compatibility | Ø1.85 in (Ø47.0 mm) pedestal bases |
| Recommended base adapter | PB4(/M) or PB4R(/M) |
| Slot length | 2.12 in (53.8 mm) |
| Slot type | Counterbored slot |
| Screw interface | 1/4″-20 (M6) cap screw |
| Body material | Stainless steel |
| Contact geometry | Three-point contact with the table surface |
| Rotation when screw is loosened | 360 degrees |
| Table compatibility | Imperial 1/4″-20 and metric M6 optical tables and breadboards |
| Quantity supplied | 5 |
The pack size row is the one that matters commercially, and the pack content row is the one that matters practically. Five identical forks behave predictably: the fifth is a spare with the same geometry as the first four. Five assorted forks would need to be measured and sorted before they could be issued, and a mixed set is worse than no set at all on a platform that is trying to standardise.
Applications
Fitting out a new platform in one purchase. A platform with five Ø1.85 in bases needs five forks. Buying the pack closes the line item in one order, with one lead time and one customs entry, instead of five separate small orders that each carry a fixed handling cost larger than the part. This is the ordinary case and the reason the pack exists.
Standardising a bench that has drifted. Benches accumulate clamp hardware from three generations of builds. A pack of one model is the cheapest way to pull a bench back to a single standard: fit the new forks to the bases that matter, retire the odd ones into a labelled box, and the next person to open the drawer finds one part number instead of four.
Keeping a float for temporary rigs. A demo rig, a loaned base, a visiting student project: all of them borrow a fork and none of them return it on schedule. A pack issued as four in service plus one float keeps the platform complete while the float circulates.
Teaching laboratories with a fixed kit list. A kit list that says five forks per station is auditable. A kit list that says some forks, various, is not. The pack makes the inventory line countable at the start and end of a semester.
Production cells that replicate a fixture. Where the same sub-assembly is built several times, the clamp hardware is specified once and replicated. Five identical forks is the natural replication unit, and identical geometry means the fixture behaves the same at every station.
Service spares held off the bench. A sealed pack in a stores cupboard is the difference between a station that is back in service in ten minutes and one that waits for a delivery. The pack stays sealed until it is needed, which also keeps the five forks from being absorbed one at a time into unrelated projects.
Selection Guide
Work down this list once per platform, not once per station. The answers are platform-level decisions, and treating them as station-level decisions is how a bench ends up with mixed hardware.
| Step | Decision | How to settle it |
|---|---|---|
| 1 | Count the Ø1.85 in bases | Walk the layout drawing and count base flanges, not mounts. One base, one fork, in the normal case. |
| 2 | Add the float | One extra fork per platform, so that a borrowed or mislaid unit does not stop a station. |
| 3 | Pick one slot length for the platform | 2.12 in (53.8 mm) unless the bases are dense or placed accurately. Mixed lengths on one table are the failure mode to avoid. |
| 4 | Choose pack or single | If the total from steps 1 and 2 is four or more, buy packs. Below that, single units are easier to account for. |
| 5 | Confirm the base adapter | PB4(/M) or PB4R(/M). Check the flange diameter if a different base family is already installed. |
| 6 | Confirm the screw | 1/4″-20 on an imperial table, M6 on a metric table, short enough that the head sits in the counterbore. |
The build-order table below turns those decisions into a shopping list. It is deliberately written as a BOM rather than as a feature list, because that is the form in which the information is actually used.
| BOM line | Item | Quantity rule for a platform |
|---|---|---|
| 1 | Pedestal base, PB4(/M) or PB4R(/M) | One per station |
| 2 | Clamping fork PF175B, from this pack | One per base, plus one float per platform |
| 3 | Cap screw, 1/4″-20 or M6 | One per fork, length matched to base and fork stack |
| 4 | Ball driver or short hex key in the matching size | One per bench, not per station |
| 5 | Spare pack held in stores | One pack per two platforms |
One cost that belongs in the decision and is usually left out: the footprint. A 2.12 in slot plus the fork body occupies more than 50 mm of table length, and it does so at whatever angle the fork happens to be rotated to. On a platform where two bases sit 50 mm apart, two long forks cannot both be fitted without interfering. That is the case where the shorter fork is the right part, and it is worth checking the base spacing before committing a whole platform to the long version.
Series Comparison
| Model | Slot length | Pack | When it is the right purchase |
|---|---|---|---|
| PF85B | 0.85 in (21.6 mm) | Single | Dense layout, base close to nominal, one station to prove out |
| PF85B-P5 | 0.85 in (21.6 mm) | 5 forks | A dense platform being fitted out as a whole |
| PF125B | 1.25 in (31.8 mm) | Single | General purpose, small placement error to absorb |
| PF125B-P5 | 1.25 in (31.8 mm) | 5 forks | A general-purpose platform being fitted out as a whole |
| PF175B | 2.12 in (53.8 mm) | Single | One extra station added to a platform already using long slots |
| PF175B-P5 | 2.12 in (53.8 mm) | 5 forks | This page. A platform with four or more bases, standardised on the long slot |
The choice between the three lengths is a choice about how much placement error the platform has to absorb, and the choice between single and pack is a choice about quantity. They are independent, and the table above is arranged so that the quantity decision can be read off the pack column without re-reading the slot lengths.
FAQ
Q: Are all five forks in the pack the same?
A: Yes. Five PF175B forks, each with a 2.12 in (53.8 mm) slot, a stainless body, three-point contact and a 1/4″-20 (M6) screw interface. The pack is not a mixed set of slot lengths and does not contain any of the shorter variants.
Q: When should I buy the PF125B-P5 pack instead of this one?
A: Choose the PF125B-P5 when the platform is dense, when bases sit within about 25 mm of each other, or when the bases are placed accurately from a drawing and the extra 22 mm of bar would only interfere with neighbouring hardware. Choose this pack when bases are placed by eye, when a tapped hole under the base is already occupied, when clamps have to be rotated well off the base centre, or when one part number has to cover stations with different base spacings. The 2.12 in slot buys tolerance to placement error and pays for it in table area.
Q: How do I keep five loose forks from turning into three forks of two different lengths?
A: Do not break the pack until it is issued. Keep the pack sealed in stores, issue it against a station number, and when it is opened, write the slot length on the storage box. The three fork lengths look alike and differ only in how far the slot extends, so an unlabelled drawer will eventually produce a base clamped by a fork whose screw head sits on the counterbore shoulder instead of in it.
Q: How should the pack be reconciled on receipt?
A: Count five against the packing list and check that all five carry the same slot length, which is done by laying them side by side and comparing the slot end positions rather than by reading a label. Record the pack against the platform it was bought for. A pack that is received and put into a general drawer without that record is a pack that will be partly gone within a month.
Q: Is the long slot the right default for a new platform?
A: For a platform built from a drawing on a 25 mm hole grid, the middle length is often enough and takes less room. For a platform that is assembled and then re-arranged, or that has to accept bases placed around existing equipment, the long slot is the more forgiving default. If the base spacing is under about 60 mm, check the footprint before standardising on the long version.
Q: Why the PB4(/M) or PB4R(/M) base adapter?
A: The fork clamps a flange, and the PB4 family is the pedestal base with a 47.0 mm flange that the fork mouth was dimensioned for. A post or post holder has no flange at table level for the fork to bear on, so the three-point contact geometry never develops and the clamp does nothing useful.
Q: How tight should the cap screw be?
A: Tight enough that the base cannot be rotated by hand, and no more. The manufacturer warns that significant over-tightening deforms the optical table surface, which misaligns the mounted components and reduces stability, and the deformation is permanent. The long fork has a longer lever than the short one, so the same wrist force does more damage here.
Q: Can the forks be used with a metric table?
A: Yes, with an M6 cap screw. The fork accepts either 1/4″-20 or M6, so a single pack can serve both standards as long as the screws are ordered to match the tables.
Usage Precautions
- Do not over-tighten. Significant over-tightening deforms the table surface, which misaligns what is mounted and reduces stability. The mark is permanent and the flatness around it is not recoverable. Tighten until the base will not turn by hand, then stop.
- Check every fork in the pack before issuing it. Five units is few enough to inspect by eye: look for a bent ear, a damaged slot shoulder, or a thread with a burr from handling. A bent fork clamps at an angle and lets the base creep.
- Keep the pack together until it is issued. Breaking a sealed pack to take one fork is how the remaining four end up in three different drawers with no record of the slot length.
- Seat the screw head in the counterbore. A head standing proud of the fork surface will catch cables and foul neighbouring mounts, and a head resting on the shoulder means the slot does not match the base position.
- Mind the footprint when several forks share a table. The bar and slot together occupy more than 50 mm. Two long forks on bases 50 mm apart will interfere, so set the clamp directions before the bases are finally tightened.
- Clean the contact pads and the table. Debris under one of the three pads turns the three-point contact into a pivot. Wipe both surfaces before fitting.
- Run the screw in by hand first. A stainless thread with a burr will gall on the first powered or wrench-driven installation and the fork is then scrap.
- Store the spare dry and labelled. Stainless tolerates a damp stores cupboard far better than an optical component does, but a labelled box is what keeps the part findable, and findable is the entire point of holding a spare.
Disclaimer
This page summarises the manufacturer specification for the PF175B fork and describes how the five-unit pack is best used when a platform is being fitted out. Quantities in the BOM tables are rules of thumb for planning, not requirements imposed by the manufacturer, and they should be adjusted for the number of stations and the way a particular laboratory issues hardware. Drawings and tolerances on the current datasheet take precedence over anything stated here, and specifications may change without notice. Price is not stated on this page and is confirmed at quotation, together with the lead time for the quantity requested.
Contact Us
Send the number of Ø1.85 in bases, the base spacing where it is tight, and the table thread. The sales team will confirm whether one pack covers the platform, whether the long slot will fit the spacing, and whether a mixed order of long and middle forks is the better answer than standardising on one. Larger platform quantities, project schedules that need the hardware in phases, and requests for the current drawing are all handled through the same enquiry.









Reviews
There are no reviews yet.