Description
Product Overview
A mirror blank and a mirror are two different products that happen to share a shape. A blank is a piece of polished substrate with a defined geometry, a defined surface figure and a defined surface quality, and with nothing on it. It makes no promise about reflectance, because it has no coating to reflect with. An uncoated fused silica disc at normal incidence reflects about four percent per surface, split between the front and the back, and the transmitted beam is the one that carries almost all the energy. Anyone who mounts this part in a beam line expecting it to turn the beam will be disappointed, and will usually conclude that the optic is faulty rather than that the wrong product was ordered.
The PF20-03 is therefore bought for what it is, not for what it could become. Three kinds of buyer account for nearly all of them. The first has a coating run booked and needs substrates that meet a figure and a cosmetic specification before the chamber is pumped down. The second needs a reference surface of known figure, and a polished disc with lambda/10 peak to valley is exactly that. The third needs a transmission reference or a window, where the absence of a coating is the point rather than a limitation.
The geometry is 50.8 mm (2 in) in diameter with a tolerance of +0.0 and -0.1 mm, so the part is never oversize for its mount bore and is always a light clearance fit. Thickness is 12.0 mm with a tolerance of plus or minus 0.2 mm. That thickness is not arbitrary on a two-inch disc: it is what keeps the surface figure stable when the optic is held in a ring, and it is the reason a 12 mm blank can be clamped without the lambda/10 specification collapsing the moment a retaining ring touches it.
Surface quality is 10-5 scratch-dig, which is tighter than the 40-20 grade used on most coated mirrors. That is not a marketing flourish; it follows from the process. A substrate is inspected before coating, and a defect that is present in the polish is amplified by the film deposited over it, so the substrate specification is set tighter than the delivered specification of the coated part. The front face is figured under lambda/10 peak to valley, the clear aperture is 90 percent of the diameter, and the rear face is fine ground rather than polished.
The material is substrate-grade fused silica. It transmits well from 185 nm to 2.1 µm, measured on a 10 mm thick uncoated sample, which is why the same blank can serve as a window or as the substrate for a filter as readily as it can serve as the base for a mirror coating. A lambda/20 figure is available as a custom option through technical support, and volume pricing applies when several blanks are ordered together.
Key Features
- Uncoated fused silica substrate. No film, no reflectance specification, no coating to degrade. The part is defined entirely by geometry, figure and cosmetic grade.
- 10-5 scratch-dig. The tight grade used for substrates before coating, because a polish defect is magnified by the film that is later deposited over it.
- Front surface figured under lambda/10 peak to valley. Suitable as a reference flat and as the base for a high-quality front-surface coating.
- 50.8 mm (2 in) diameter, +0.0 / -0.1 mm. A one-sided tolerance, so the disc always clears its mount bore instead of seizing in it.
- 12.0 mm nominal thickness, plus or minus 0.2 mm. Thick enough that a two-inch disc keeps its figure when it is held in a ring or a clamp.
- Clear aperture 90 percent of diameter. The outer rim is the mounting zone, not optical surface, and the figure is guaranteed only inside the clear aperture.
- Rear face fine ground. A ground back scatters rather than specularly reflects, which removes the ghost return that a polished back would send back down the beam path.
- High transmission from 185 nm to 2.1 µm. Measured on a 10 mm uncoated sample, so the same material works as a deep ultraviolet window, a visible substrate or a near infrared window.
- Lambda/20 figure available to order. For reference flats and interferometric use where lambda/10 is not enough.
- Four sizes in the family. Ø1/2 in, Ø19 mm, Ø1 in and Ø2 in, so a coating run can be planned across several apertures from one substrate specification.
Technical Specifications
| Parameter | Specification |
|---|---|
| Model | PF20-03 |
| Product type | Mirror blank, uncoated |
| Material | Substrate-grade fused silica |
| Diameter | 50.8 mm (2 in) |
| Diameter tolerance | +0.0 / -0.1 mm |
| Thickness | 12.0 mm, plus or minus 0.2 mm |
| Surface quality | 10-5 scratch-dig |
| Front surface figure | Under lambda/10 peak to valley |
| Clear aperture | 90 percent of diameter |
| Rear surface | Fine ground |
| Coating | None |
| Reflectance | Not specified. An uncoated surface reflects approximately 4 percent at normal incidence and is not usable as a mirror. |
| Transmission | High transmission from 185 nm to 2.1 µm, measured on a 10 mm thick uncoated sample |
| Figure upgrade | Lambda/20 available as a custom option |
| Quantity pricing | Volume discounts available |
| Family sizes | Ø1/2 in, Ø19 mm, Ø1 in, Ø2 in |
| Intended use | Substrate for a front-surface coating, reference surface, window or filter substrate |
The reflectance row is deliberately not a number. There is no meaningful reflectance specification for an uncoated blank, and any figure quoted for one would describe a bare Fresnel reflection rather than a usable mirror. The transmission row carries the wavelength range because that is the property the material actually guarantees, and it is measured on a 10 mm sample, which is close enough to the 12.0 mm thickness of this part that the comparison is fair.
Applications
Substrates for an in-house coating run. This is the main use. A laboratory with access to an evaporator or a sputter system buys blanks to a figure and a cosmetic grade, coats them with whatever the experiment needs, and keeps control of the coating design. The 10-5 polish matters here because the coater cannot improve a surface it receives; it can only add to it. A scratch that would be acceptable on a finished 40-20 mirror is a defect that the film will decorate.
Reference surfaces and test plates. A polished disc of known figure, uncoated, is a useful reference in a shop that builds interferometers or tests mounts. The absence of a coating is an advantage: there is no film stress to change the figure with temperature, and no coating run to repeat when the reference is damaged. Lambda/10 is adequate for most mount and stage work; the lambda/20 option exists for the cases where it is not.
Windows and filter substrates. With high transmission from 185 nm to 2.1 µm and a 12 mm thickness, the part can be used directly as a window in a cell, a chamber viewport on a low-pressure system, or the substrate for a dielectric filter that will be deposited later. The ground rear face is useful in a window application because it kills the second surface ghost, which is the reflection that ruins a measurement in a dual-beam spectrometer.
Transmission references. When a spectrometer or a photometer needs a known-good uncoated part in the beam to check linearity or to measure a baseline, a blank of this quality is a defensible reference. It is homogeneous, it is stable, and it has no coating that could age.
Prototype substrate selection. A design team that does not yet know which coating it will use can buy the blank first, prove the mechanical interface, the mount and the clear aperture, and specify the coating afterwards. That sequence avoids committing to a coating before the optomechanics are settled, which is the usual order in which a prototype gets into trouble.
Replacement of a damaged coated part. Where a coated mirror has been scratched and the coating house is in-house, stripping and re-coating an existing blank is often faster than ordering a finished part. A spare blank on the shelf keeps that option open.
Selection Guide
The first question is not which coating but whether a coating is needed at all. If the answer is yes, this blank is the input to that decision rather than the output, and the selection work belongs to the coater. If the answer is no, the blank is the product and the decision reduces to size, figure and quantity.
| Requirement | What to choose | Reason |
|---|---|---|
| Turn a beam, fold a path, act as a mirror | A coated mirror, not this part | An uncoated surface reflects about 4 percent and transmits the rest; it cannot function as a mirror |
| Substrate for a custom or in-house coating | PF20-03 blank | 10-5 polish and sub lambda/10 figure give the coater a surface worth coating |
| Reference flat for interferometry | PF20-03, or the lambda/20 option | Figure is the only relevant property and no coating is wanted |
| Window or filter substrate | PF20-03 blank | 185 nm to 2.1 µm transmission and a ground rear face that suppresses the ghost |
| Standard visible to near infrared reflection | A finished protected metal mirror of the same size | The finished part carries the reflectance specification and the cosmetic grade appropriate to a coated surface |
| High power laser reflection | A finished coated part rated for the fluence | Neither a blank nor an unrated coating should be used in a high fluence beam |
On size, the family covers Ø1/2 in, Ø19 mm, Ø1 in and Ø2 in. This page is the Ø2 in member. The Ø19 mm size exists for a specific mount family and is not interchangeable with the inch sizes; if a design calls for Ø19 mm, order that size rather than assuming a 0.75 in disc will fit. On figure, lambda/10 peak to valley covers most coating substrates, because the coating house will usually measure and, if necessary, figure the part after deposition. The lambda/20 option is worth the extra step when the blank is itself the reference and no post-coating correction is possible.
On quantity, volume pricing applies, and it is worth planning a coating run as a batch: several blanks of the same size coated in one pump-down costs far less per part than coating them one at a time. That is the practical reason a laboratory keeps two or three blanks on the shelf rather than ordering exactly what it needs for the next experiment.
Series Comparison
The same substrate is offered as a family of finished mirrors, and the comparison below is a comparison of what the finished parts add. This page is the uncoated member of that family; the other part numbers are coated and are ordered when a reflectance specification is needed rather than a substrate.
| Part number | Coating | Nominal band | What it adds over the blank |
|---|---|---|---|
| PF20-03 | None | Not applicable | This page. Geometry, figure and polish only, no reflectance specification |
| PF20-03-G01 | Protected aluminium | 450 nm to 20 µm | Broadband metal reflection with a protective overcoat, the general-purpose finished option |
| PF20-03-M01 | Protected gold | 800 nm to 20 µm | Infrared reflection with a protective overcoat, for wavelengths beyond the useful range of aluminium |
| PF20-03-M03 | Unprotected gold | 800 nm to 20 µm | Higher reflectance than the protected version, at the cost of a surface that cannot be cleaned |
| PF20-03-P01 | Protected silver | 450 nm to 20 µm | The highest reflectance metallic coating in the visible to near infrared, with a protective overcoat |
One difference between this page and every other row in that table deserves to be explicit. The coated members of the family are delivered to a cosmetic grade suited to a finished reflective surface, while the blank is inspected to the tighter 10-5 grade because it is a substrate and not a finished optic. The two grades are not in competition and neither is a defect: a coated mirror is judged on a coated surface, and a substrate is judged before any film is applied. A buyer who compares the numbers without that context will conclude that the blank is the better part, which is exactly the wrong conclusion for a reflective application.
FAQ
Q: Can this blank be used directly as a mirror?
A: No. An uncoated fused silica surface reflects about four percent at normal incidence and transmits the remainder, so it will not turn a beam in any useful sense. It must be coated before it can serve as a mirror. If a reflective part is what is needed, order one of the finished coated versions of the same substrate rather than a blank.
Q: Why is the surface quality tighter than on the coated mirrors?
A: Because a substrate is inspected before coating, and a film deposited over a defect makes the defect worse rather than hiding it. The blank is therefore specified to the 10-5 grade, while a finished coated mirror of the same size is delivered to the looser 40-20 grade that applies to a coated reflective surface. The difference describes two stages of the same production route, not two quality levels of the same product.
Q: Is the rear face polished?
A: No. The rear face is fine ground, which scatters rather than specularly reflecting. That is usually what is wanted, because a ground back removes the ghost return that a polished back would send back along the beam path. If a polished rear face is required, that is a different part in the family rather than a modification of this one.
Q: What thickness tolerance should a mount be designed to?
A: 12.0 mm nominal, plus or minus 0.2 mm. A retaining ring or clamp should be dimensioned so that the full tolerance band is accommodated without loading the optic through its edge, because edge loading is the usual way a lambda/10 surface becomes something worse once it is mounted.
Q: Why does a two-inch disc need to be this thick?
A: Because figure and mounting interact. A thin disc of 50.8 mm diameter will bend under its own weight in a ring mount and will bend further under a retaining ring, and the lambda/10 specification applies to the part as delivered, not to the part as clamped. Twelve millimetres gives enough stiffness that ordinary mounting practice does not destroy the figure.
Q: Can it be used as a window?
A: Yes. The material transmits well from 185 nm to 2.1 µm, and the ground rear face suppresses the second surface ghost. It is not a certified pressure window and should not be used as a barrier between a vacuum chamber and atmosphere without an engineering check, but as an optical window in a low differential pressure application it is a reasonable part.
Q: How is the lambda/20 option ordered?
A: As a custom request through technical support, not as a catalogue line. Lead time is longer than for the standard lambda/10 part because the figuring step is longer, and the price reflects the additional polishing. It is worth ordering only where the blank is itself the reference, since a coating house will normally measure and correct figure after deposition.
Q: Does the part carry any identification marking?
A: No part number is marked on the substrate itself, so identification depends entirely on the packaging and on whatever labelling the laboratory applies. Keep the blank in its packaging until it is issued, and label the edge or the storage box if several sizes are held together, because a 50.8 mm blank and a 50.8 mm coated mirror are indistinguishable by eye in a dim room.
Usage Precautions
- Handle by the edge, with gloves or finger cots. The surface to be coated must be clean before it goes into the chamber. A fingerprint left on a substrate is not merely a cosmetic problem; it is contamination that has to be removed, and if it is not, it becomes a defect under the film.
- Do not polish or wipe with anything abrasive. No polishing compound, no abrasive pad, no dry tissue on a dry surface. The 10-5 grade describes the surface as supplied and it is easy to make it worse.
- Keep the blank clean so that it does not need re-cleaning before coating. Every cleaning step before deposition is a chance to add a sleeker or a scratch. Store the part in its packaging, handle it only when necessary, and let the coating house do the final clean.
- Do not clamp it as if it were a mirror. The figure is specified on an unmounted part. A retaining ring tightened by feel will bend a 12 mm disc enough to matter, and the resulting astigmatism will be blamed on the coating.
- Design the mount to the thickness tolerance. Plus or minus 0.2 mm on 12.0 mm is a wide enough band that a close-fitting pocket can bind. Allow clearance and use a retaining method that does not rely on the exact thickness.
- Protect the ground rear face from contamination. A ground surface traps particles and is difficult to clean. In a vacuum application, a ground face that has been handled will outgas for longer than a polished one.
- Label the storage. Because nothing is marked on the blank and it looks exactly like the coated mirrors of the same diameter, an unlabelled shelf will eventually produce a coating run on a part that was already coated, or a beam line built around an uncoated disc.
- Do not assume a coating house will accept any substrate. Confirm the figure, the cosmetic grade and the material with the coater before ordering a batch. Some coating processes require a specific surface preparation that a general-purpose blank may not have been prepared for.
Disclaimer
The values on this page are the manufacturer published specification for the PF20-03 fused silica mirror blank and are reproduced so that a coating run or a mechanical design can be planned without opening a datasheet. Figure, cosmetic grade and dimensional tolerances are guaranteed by the manufacturer under its own inspection conditions, not by this page. No reflectance value is quoted because no reflectance specification exists for an uncoated part, and the approximate four percent Fresnel reflection mentioned above is a property of the material rather than a product specification. Specifications may change without notice; the current datasheet governs. Price is not shown and is confirmed at quotation, including any volume pricing for a batch.
Contact Us
For a coating run, send the aperture, the quantity, the figure grade required and the wavelength range, and the sales team will confirm what can be supplied from stock and what needs to be ordered. For the lambda/20 option, or for a batch that mixes two of the family sizes, expect a longer quotation because the figuring and the packaging are handled per batch rather than per part. If a design is still deciding between a blank and a finished coated mirror, describe the application and the beam rather than the part number, and the answer will be quicker and more useful.









Reviews
There are no reviews yet.