QQ: 859818709

Thorlabs PF2011 Ø50.8 mm (2 in) Zerodur® Mirror Blank, 12.0 mm Thick, Uncoated

Thorlabs PF2011 Ø50.8 mm (2 in) Zerodur® Mirror Blank, 12.0 mm Thick, Uncoated

Price on request
Category:

Description

Thorlabs PF2011 Ø50.8 mm (2 in) Zerodur® Mirror Blank, 12.0 mm Thick, Uncoated

Product Overview

What a mirror blank is

The PF2011 is an uncoated optical substrate: a 50.8 mm (2 in) round Zerodur® disc, 12.0 mm thick, polished on the front face to λ/10 at 632.8 nm with a 10-5 scratch-dig surface quality, a clear aperture of 90 percent of the diameter (45.7 mm), parallelism of 3 arcmin or better, a fine-ground rear surface, and the part number engraved on the back side. It carries no coating of any kind, which is the point of the part rather than a limitation of it.

Thorlabs describes the intended use directly: these blanks are designed to be used as front-surface mirrors once coated. The blank is the substrate that a coater turns into a mirror. It arrives with the two properties that a coater cannot add — the figure and the surface quality — and without the one property the coater is being engaged to provide, which is the reflective film.

How thermal beam drift actually happens

A mirror in a high-power beam absorbs a small fraction of the light that it reflects. Even at 99 percent reflectance, one percent of a kilowatt is ten watts deposited in a substrate a few millimetres thick. That heat raises the substrate temperature, the substrate expands, and because the expansion is not uniform — the coated face is warmer than the back, and the centre of the illuminated area is warmer than the rim — the surface acquires a curvature it did not have when it was tested.

That curvature is the whole problem. A λ/10 surface that bows by a quarter wave no longer delivers a λ/10 wavefront. The reflected beam leaves with a phase error proportional to the deformation, and a phase error across the aperture is a divergence. In the far field the focal spot grows, the peak intensity falls, and — the part that ruins experiments rather than just degrading them — the spot moves. The beam drifts because the mirror is bending, not because anything moved on the table.

The material number that decides the magnitude

The amount of bow for a given absorbed power scales with the coefficient of thermal expansion. Zerodur® has a CTE specified as 0 ± 0.100 × 10⁻⁶/°C, meaning that across the specified temperature range the expansion is essentially zero and the tolerance band is a tenth of a part per million per degree. Fused silica, the material used for the coated mirrors in this same family, has a CTE of 0.55 × 10⁻⁶/°C.

Put the two numbers side by side: 0.55 against a band of ± 0.100. The fused silica value is about five and a half times the magnitude of the Zerodur tolerance, and the Zerodur nominal is zero. This is not a small improvement in a figure of merit; it is the difference between a substrate that bends under load and one that, to first order, does not. For a CO₂ laser delivery mirror, an amplified Ti:sapphire compressor fold, or an industrial processing head where the beam position at the workpiece is a tolerance, that difference is what the blank is bought for.

Thorlabs names exactly these systems as the intended applications: CO₂ lasers, amplified Ti:sapphire lasers, industrial processing lasers, and other applications that are sensitive to thermally induced beam drift. For applications that are not sensitive to thermal drift, Thorlabs offers a separate line of fused silica blanks, which are less expensive and entirely adequate.

Key Features

  1. Zerodur® substrate with CTE of 0 ± 0.100 × 10⁻⁶/°C. A near-zero expansion coefficient with a tight tolerance band, so that absorbed laser power produces negligible figure change. This is the defining property of the part and the reason to choose it over a fused silica blank.
  2. 10-5 scratch-dig surface quality, uncoated. Stricter than the 40-20 specified on the coated mirrors in this family, and deliberately so: a coater can add material but cannot remove it, so every scratch present on the substrate is reproduced, and to some degree exaggerated, in the finished coating.
  3. λ/10 at 632.8 nm surface figure. The figure is quoted at the helium-neon line on which the interferometric test is performed. On a blank this is the property the customer is actually buying, because it is the one that survives the coating process unchanged.
  4. 12.0 mm thickness for stiffness and heat spreading. The thick body resists the print-through that a retaining ring imposes, and it spreads absorbed heat laterally so that the local temperature rise under a small spot is lower than it would be in a thin disc.
  5. Parallelism of 3 arcmin or better, with a fine-ground back surface. The Fine Ground rear face is a mounting reference, not an optical surface, and the parallelism specification keeps the front face’s orientation predictable when the disc is seated against a flat mount.
  6. Part number engraved on the back side. Each blank is engraved with its part number on the rear face, so a substrate that has been coated, mounted and in service for years can still be identified without removing it from its holder.
  7. Available in three diameters. Ø1/2 in (12.7 mm) at 6.0 mm thick, Ø1 in (25.4 mm) at 6.0 mm thick, and Ø2 in (50.8 mm) at 12.0 mm thick — the size on this page. The two smaller sizes share the 6.0 mm body; only the two-inch blank is 12.0 mm.

Technical Specifications

Parameter Specification
Part Number PF2011
Product Type Uncoated mirror blank (substrate only, no reflective film)
Material Zerodur®, substrate grade
Coefficient of Thermal Expansion 0 ± 0.100 × 10⁻⁶/°C
Diameter 50.8 mm (2 in), +0.0 / -0.1 mm
Thickness 12.0 mm (0.47 in), ±0.2 mm
Surface Flatness λ/10 at 632.8 nm, peak to valley
Surface Quality, Front 10-5 scratch-dig
Clear Aperture 90% of diameter (45.7 mm)
Parallelism 3 arcmin or better
Back Surface Fine Ground
Marking Part number engraved on the back side
Coating as Supplied None
Coatings That Can Be Applied Broadband dielectric, metallic, or custom coatings, ultraviolet to near infrared
Angle of Incidence Not applicable before coating; 0° to 45° once coated
Typical Systems CO₂ lasers, amplified Ti:sapphire lasers, industrial processing lasers, thermally drift-sensitive applications
Alternative Material Fused silica blanks for applications not sensitive to thermal drift

One specification needs explaining because it looks inconsistent with the rest of the family. The coated mirrors on the same 50.8 mm body are specified at 40-20 scratch-dig; this blank is specified at 10-5. The reason is that coating is an additive process. A coating can fill a microscopic scratch only by burying it, and a buried scratch scatters more than an open one because the film conforms to the defect and adds interference structure around it. A substrate therefore has to be cleaner than the finished part is required to be, and the 10-5 specification is the margin that the coating process consumes.

Applications

This part is a starting point, not a finished component. The applications below are all stages that come before a mirror exists, or roles in which the substrate is used without ever becoming a mirror.

  • Substrate for a custom coating. The most common use. A laboratory needs a mirror at a wavelength or with a bandwidth that no catalogue coating provides, so it buys a blank with a known figure and sends it to a coating house. The coater receives a substrate whose surface quality and flatness are already specified, which removes the largest source of disagreement in a custom coating job.
  • Substrate selection for thermally sensitive high-power systems. Where the beam power is high enough that absorbed light will warm the optic, the choice of substrate determines whether the far-field spot stays put. The CTE of 0 ± 0.100 × 10⁻⁶/°C is the reason this blank exists, and the systems named by Thorlabs — CO₂, amplified Ti:sapphire, industrial processing — are the ones where the effect is measurable.
  • Prototype and trial builds. A new optical layout can be assembled and aligned with uncoated blanks to check clearances, mount interfaces and beam heights before committing to coated optics. The blanks are then coated once the geometry is settled, or retained as mechanical references.
  • Reference surface for figure and finish. A 10-5 surface flat to λ/10 at 632.8 nm is a useful comparison standard in its own right, both for judging the condition of coated optics and for checking the alignment of an interferometer.
  • Coating process development. A coating group that needs to separate film behaviour from substrate behaviour works from substrates of known and identical specification, so that a change in measured performance can be attributed to the process rather than to the part.
  • Athermal mirror design. In an instrument where the mirror figure must hold over a temperature range rather than at a single temperature, the substrate’s expansion coefficient enters the design directly. A near-zero CTE substrate removes one term from the tolerance stack before the coating is even considered.

Selection Guide

The first decision is not which blank, but whether a blank is the right purchase at all. The second is the material, and only the third is the size.

Blank or finished mirror. If a catalogue coating covers your wavelength, buy the coated mirror. The coated parts in this family arrive with the film applied, the reflectance measured and the surface quality guaranteed at 40-20, and they cost less than a blank plus a custom coating run. Buy the blank when no catalogue coating fits — an unusual wavelength, a bandwidth requirement, a dielectric design, a coating that has to survive a specific environment — or when the substrate material itself is the reason for the purchase, as it is here. A custom coating adds lead time and cost, and it is only justified when the coating is genuinely custom.

Zerodur® or fused silica. Choose Zerodur® when thermally induced beam drift is a specified concern: high average power, tight pointing stability, long integration times, or a system where the optic cannot be actively cooled. Choose fused silica when it is not. Thorlabs states the distinction plainly, offering the fused silica blank line for applications that are not sensitive to thermal drift, and there is no reason to pay for thermal stability that the application does not need.

Size. Three diameters are available. The Ø1/2 in (12.7 mm) and Ø1 in (25.4 mm) blanks are 6.0 mm thick; the Ø2 in (50.8 mm) blank on this page is 12.0 mm thick. The step in thickness is not cosmetic: it keeps the aspect ratio of the disc roughly constant, so the two-inch part is as stiff relative to its span as the smaller ones, and it provides more material to spread absorbed heat away from a small illuminated spot.

What to check before ordering. Confirm the coating house can handle a 50.8 mm disc of 12.0 mm thickness, confirm the coating design is compatible with the substrate material and its surface finish, and confirm that the 10-5 surface is not going to be degraded by handling between delivery and coating. The last point is the one that catches people: a blank that is scratched in incoming inspection is a blank that has to be replaced, because there is no polishing step between the shelf and the coater.

Series Comparison

Two comparisons matter for this part: substrate material, and the available sizes. The first decides whether the blank does its job; the second decides which one to order.

Property Zerodur® (this blank) Fused silica (alternative line)
CTE 0 ± 0.100 × 10⁻⁶/°C 0.55 × 10⁻⁶/°C
Relative thermal expansion Near zero nominal About five and a half times the Zerodur tolerance band
Sensitivity to thermal beam drift Low; the reason to specify this material Acceptable where drift is not specified
Typical use CO₂ delivery, amplified Ti:sapphire, industrial processing heads General laboratory optics, low-power routing, imaging
Cost position Higher Lower

The size table below is the practical ordering reference. Note that only the two-inch blank is 12.0 mm thick, and that all three sizes share the same 90 percent clear aperture rule and the same λ/10 figure.

Nominal Size Diameter Thickness Clear Aperture
1/2 in 12.7 mm 6.0 mm 90% of diameter
1 in 25.4 mm 6.0 mm 90% of diameter
2 in (this part) 50.8 mm 12.0 mm 45.7 mm

Zerodur® is a registered trademark of Schott. The material designation is Schott’s, and the substrate grade used here is the grade intended for mirror blanks rather than for transmissive optics.

FAQ

Q1. Can I use this blank as a mirror straight out of the box?

No. It has no coating, and an uncoated polished surface is a poor reflector. At normal incidence a bare glass or glass-ceramic surface reflects only about 4 percent of the light and transmits the rest, which makes it useless as a mirror and potentially hazardous as a beam dump, since the transmitted beam continues through the optic. The part is designed to become a front-surface mirror once a reflective coating has been applied; before that step it is a substrate.

Q2. Why is the surface quality 10-5 here when the coated mirrors are 40-20?

Because coating can only add material, never remove it. A scratch on the substrate is covered by the film, not repaired by it, and a covered scratch scatters more than an open one because the film conforms to the defect and adds interference structure around it. The substrate therefore has to be cleaner than the finished part is required to be, and 10-5 is the margin the coating process consumes. It also means the blank has to be handled with more care than a coated mirror, not less.

Q3. How much better is Zerodur® than fused silica, in numbers?

The CTE of this substrate is 0 ± 0.100 × 10⁻⁶/°C; the CTE of fused silica is 0.55 × 10⁻⁶/°C. The Zerodur nominal is zero, and its tolerance band is a tenth of a part per million per degree, so the Zerodur expansion is about one fifth of the fused silica value even at the edge of its band. In a system where the figure has to hold under absorbed laser power, that difference in expansion is the difference between a wavefront that drifts and one that does not.

Q4. What coatings can be applied to this blank?

Thorlabs states that these blanks can be coated with broadband dielectric coatings, metallic coatings or custom coatings, covering the ultraviolet through the near infrared. In practice the choice belongs to the coating house and to the application: a metal film for broadband reflectance, a dielectric stack for maximum reflectance inside one band, or a custom design for a specific wavelength and angle. The blank’s contribution is a known figure and a known surface finish, which is what makes the coating result predictable.

Q5. Does the engraved part number survive coating and mounting?

It is engraved on the back side, which is a Fine Ground surface and not an optical one, so the marking is outside the coated area and outside the clear aperture. A mounted blank can therefore be identified by looking at its rear face, which is exactly the situation where identification matters: after the optic has been in a holder for years and the original packaging is long gone.

Q6. Should I buy the blank or a coated mirror for a CO₂ beam delivery path?

If a catalogue coating covers 10.6 µm, buy the coated mirror: it arrives finished, with the reflectance specified and the surface quality guaranteed, and it avoids a separate coating cycle. Buy this blank when the coating has to be something the catalogue does not offer, or when the substrate material is the point — which, for a CO₂ path where absorbed power causes beam drift, it often is. The decision is between paying for a custom coating and accepting a substrate that bends under load; both are legitimate, and they answer different questions.

Usage Precautions

The handling rules for a blank are stricter than for a coated mirror, because there is no film to sacrifice and no polishing step between the shelf and the coater.

  • Treat the 10-5 surface as a finished optical surface, not as a workpiece. It is the most delicate surface in this family. A single wipe with an inappropriate tissue, a fingerprint, or a particle trapped under a lens cloth becomes a permanent defect, because there is no process that removes it short of re-polishing.
  • Keep fingerprints off, for a reason that only appears later. A fingerprint on an uncoated substrate is not merely a cosmetic mark. Organic residue that is not removed before the coating run is baked during deposition and becomes an adherent contamination layer that prevents proper film nucleation, so the coating fails to adhere in exactly the place where the fingerprint was. Clean handling now is coating yield later.
  • Do not clean it unless you have to, and then do it properly. If cleaning is unavoidable before coating, it belongs to the coating house, which has the solvents, the drag-wipe technique and the inspection capability to verify the result. Improvised cleaning in the laboratory is how a 10-5 surface becomes a 40-20 surface.
  • Never set the blank face-down. The fine-ground back is the side that should touch anything. A 12.0 mm disc set face-down on a bench rests its entire weight on the polished surface and on whatever particle happens to be under it.
  • Protect the edges. A chip at the rim propagates into the polished face during thermal cycling in the coater. Handle by the edge with gloves and never let two blanks touch each other.
  • Store flat, supported, and dry. The rear surface is Fine Ground and can be a source of particles; keep the blank in its packaging, with the polished face clear of any material, until it goes to the coater.
  • Confirm the coating design before shipping it out. Once coated, the blank’s figure and surface quality are locked in. Sending it to a coater without an agreed design and an agreed handling procedure is the most expensive way to lose a substrate.

Disclaimer

The specifications on this page are compiled from Thorlabs’ publicly published product documentation and are provided for selection reference only. Where this page and the manufacturer’s current official datasheet differ, the official datasheet governs. Material properties, sizes and surface specifications may be revised by the manufacturer without notice. This product is supplied uncoated and is not a finished mirror; reflectance, damage threshold and angle-of-incidence performance depend entirely on the coating subsequently applied by the user or by a third-party coating house, and no such performance is specified or implied here. Zerodur® is a registered trademark of Schott. Prices and lead times are confirmed at quotation.

Contact Us

If you are specifying a substrate for a high-power or thermally critical optical path and want help choosing between this Zerodur® blank and the fused silica alternative, please contact us.

Hotline: +86 159-2722-0467

E-mail: 859818709@qq.com  |  Website: www.soar-laser.cn

We can advise on the three available sizes, on mounting hardware for a 12.0 mm body, and on the practical difference between buying a blank for custom coating and buying a finished coated mirror from the catalogue.

Reviews

There are no reviews yet.

Be the first to review “Thorlabs PF2011 Ø50.8 mm (2 in) Zerodur® Mirror Blank, 12.0 mm Thick, Uncoated”

Your email address will not be published. Required fields are marked *

中文EN