QQ: 859818709

Thorlabs PF2011-M03 Ø50.8 mm (2 in) Zerodur® Unprotected Gold Mirror, 800 nm – 20 µm

Thorlabs PF2011-M03 Ø50.8 mm (2 in) Zerodur® Unprotected Gold Mirror, 800 nm – 20 µm

Price on request
Category:

Description

Thorlabs PF2011-M03 Ø50.8 mm (2 in) Zerodur® Unprotected Gold Mirror, 800 nm – 20 µm

Product Overview

A chirped-pulse amplifier asks its folding mirrors for two things that are normally bought separately. The first is optical innocence: the mirror must not add phase that the pulse compressor was not designed for, because the whole chain is balanced to a fraction of a radian of residual chirp and an unquantified layer of dielectric in the beam path puts an unquantified term into that balance. The second is mechanical stillness: the mirror must not move while the amplifier runs, because a beam that walks out of a 300 µm aperture between the stretcher and the compressor loses throughput in a way that no amount of re-tuning can recover.

Most optics satisfy one of those requirements. A dielectric mirror can be designed with controlled dispersion, but the control is only as good as the design and the run. A metal mirror on ordinary glass has no dielectric phase at all, but the glass moves when it warms. The PF2011-M03 is one of the small number of parts that satisfies both at once, and it does so by combining the two features that each solve one half of the problem: bare gold for the optical half, Zerodur® for the mechanical half.

The optical half is straightforward. Bare gold has no overcoat, therefore no dielectric layer, therefore no overcoat dispersion and no overcoat-induced polarization change. Thorlabs states the design intent directly: unprotected mirrors are the recommended choice where the polarization state has to be strictly maintained, or where dispersion inside the overcoat of a protected mirror has to be avoided. The specification is an average reflectance of 97 percent from 800 nm to 20 µm. The figure of 97 percent is the highest broadband average among the gold coatings that cover the whole 800 nm to 20 µm band on this body, and it is achieved precisely by leaving the metal bare: the protected version is specified at 96 percent, because the overcoat that protects the metal also absorbs a little and reflects a little less.

One percentage point is not why anyone buys this part, and it would be dishonest to sell it that way. What the missing overcoat buys is the absence of two effects: a polarization transformation whose magnitude depends on a coating thickness that is not published, and a wavelength-dependent phase that accumulates with every bounce. In a regenerative amplifier with eight passes off the same folding pair, an overcoat phase that is small per bounce is not small per round trip, and it enters the dispersion budget as a term that the compressor cannot compensate because it was never characterised.

The mechanical half is where the substrate earns its place. Amplified titanium:sapphire systems run at kilohertz repetition rates with millijoules per pulse, and a small fraction of that average power is absorbed in the coating, in the substrate and in the mount. Zerodur’s coefficient of thermal expansion is 0 ± 0.100 x 10⁻⁶/°C, which Thorlabs describes as significantly smaller than the fused silica value of 0.55 x 10⁻⁶/°C. The company’s own summary of why this matters is worth quoting because it names the application class: this property makes these mirrors ideal for high-power systems like CO₂ lasers, amplified Ti:sapphire lasers, and industrial machining lasers, as well as other applications that are sensitive to thermally-induced beam drift. The five-and-a-half-fold difference in expansion does not make the mirror immune to heat; it makes the mirror’s own contribution to beam drift small enough that the mount and the air path become the dominant terms, which is where you want the problem to live because those are the terms you can fix.

The price of the bare metal is paid in handling. Thorlabs describes unprotected gold as offering higher reflectance than protected gold but being more delicate, and the delicacy is not chemical. Gold does not oxidise and does not tarnish in clean air; it is one of the few metals that can sit on a shelf for a decade and come back unchanged. The delicacy is mechanical and contamination-related. A fingerprint leaves an organic film that absorbs far more than gold does. An aerosol droplet dries into a residue of different refractive index. An abrasive particle dragged across the surface removes metal rather than deforming a coating, and there is no sacrificial layer to absorb that damage. For that reason the care instruction on this part is not a suggestion: no solvent, no tissue, no drag.

Zerodur is a registered trademark of Schott.

Key Features

  1. No overcoat, therefore no overcoat dispersion and no overcoat polarization change. This is the first feature because it is the reason the part exists. With nothing between the beam and the gold, the reflection is a metal reflection: broadband, smooth in phase, and free of the dielectric interference term that a protected mirror contributes. For chirped-pulse work that term is not a curiosity, it is an unmodelled error in the dispersion budget.
  2. Polarization state preserved through reflection. Bare gold does not rotate or elliptically polarize a beam beyond the geometric effect of the incidence angle itself. Any experiment that relies on a known state at the output, from ellipsometry to polarization-resolved pump-probe, can use this mirror without characterising a coating first.
  3. Ravg of 97 percent from 800 nm to 20 µm, the highest broadband average in the protected-or-bare gold group. The 97 percent figure applies across nearly four octaves, so the same optic serves a 800 nm oscillator, a 1 µm amplifier and a 10.6 µm CO₂ line without a coating change.
  4. Zerodur® substrate at 0 ± 0.100 x 10⁻⁶/°C. The substrate is what keeps the 97 percent from being wasted: a mirror that reflects perfectly and points badly is not useful in an amplifier chain.
  5. The highest damage thresholds in this coating family. Pulsed: 4 J/cm² at 10.6 µm with 100 ns pulses at 1 Hz over a Ø0.435 mm spot, which is about 5.9 mJ in a single pulse at that fluence and that spot. CW: 1000 W/cm at 10.6 µm over a Ø1.18 mm spot, which is about 118 W of incident power at that beam size. Both figures are for a bare metal film with no dielectric to absorb or to delaminate.
  6. Three diameters only, and the two-inch is the largest. The round format in this family is offered as Ø1/2 in (12.7 mm), Ø1 in (25.4 mm) and Ø2 in (50.8 mm). There is no Ø7 mm version and no intermediate 30 mm or 40 mm size. The two-inch part on this page is the only one with a 12.0 mm body; the smaller sizes are 6.0 mm thick.
  7. λ/10 at 632.8 nm, 40-20 scratch-dig, 45.7 mm clear aperture, 3 arcmin parallelism, engraved identification on the back. The engraving matters more on a bare gold mirror than on a protected one, because a bare gold surface cannot be labelled with a sticker and should never be written on.

Technical Specifications

Parameter Specification
Part Number PF2011-M03
Coating Unprotected gold (bare metal, no dielectric layer)
Overcoat None
Spectral Range 800 nm to 20 µm
Average Reflectance Ravg of 97 percent from 800 nm to 20 µm
Dispersion Contribution No overcoat, therefore no dielectric dispersion term
Polarization Behaviour Polarization state preserved; recommended where it must be strictly maintained
Substrate Zerodur® (substrate grade)
Coefficient of Thermal Expansion 0 ± 0.100 x 10⁻⁶/°C (fused silica reference: 0.55 x 10⁻⁶/°C)
Diameter 50.8 mm (2 in), tolerance +0.0 / -0.1 mm
Thickness 12.0 mm (0.47 in), tolerance ±0.2 mm
Parallelism 3 arcmin or better
Front Surface Flatness λ/10 at 632.8 nm
Surface Quality 40-20 scratch-dig
Clear Aperture 90 percent of diameter (45.7 mm)
Angle of Incidence 0° to 45°
Back Surface Fine ground, model number laser-engraved
Pulsed Damage Threshold 4 J/cm² at 10.6 µm, 100 ns, 1 Hz, Ø0.435 mm
CW Damage Threshold 1000 W/cm at 10.6 µm, Ø1.18 mm
Cleanability Not cleanable; loose dust removal by clean dry air or nitrogen only
Available Diameters Ø1/2 in, Ø1 in, Ø2 in only

Read the two damage thresholds as a matched pair, because they come from the same test series and describe the same coating at the same wavelength. 4 J/cm² over a 0.435 mm spot is 5.9 mJ in a single 100 ns pulse; 1000 W/cm over a 1.18 mm spot is 118 W of continuous power. Both are the highest values in this coating family, and the reason is structural rather than magical: there is no dielectric layer to absorb energy, to trap heat against the metal, or to delaminate when it is heated. A bare metal film has one failure mode, melting or ablating the gold, and gold is difficult to damage that way.

One honest limitation of the data. The published thresholds for this coating are at 10.6 µm, with 100 ns pulses and a 1 Hz repetition rate. Amplified titanium:sapphire runs near 800 nm with pulses five orders of magnitude shorter and repetition rates three orders of magnitude higher. The coating is the same metal and the same film, and the 800 nm band is inside the specified range, but a 100 ns threshold at 10.6 µm does not transfer to a 100 fs pulse at 800 nm: femtosecond damage is initiated by multiphoton and avalanche processes in a time too short for thermal diffusion, and it depends on the pulse duration in a way that only measurement can settle. If the application is ultrafast, treat the published number as evidence that the film is robust and qualify the actual part at your own fluence before committing a production build.

Permitted Not permitted, ever
Blowing off loose dust with clean dry air or dry nitrogen Any solvent, including acetone, methanol, isopropanol and optical cleaning fluids
Handling by the ground edge with gloves Any tissue, wipe, swab or cloth touching the coated face
Storage in the supplied case, optic resting off its faces Dragging anything across the surface, including a dry tissue
Removal and reinstallation in a clean bench environment Any attempt to polish out a mark, a haze or a fingerprint

Applications

  • Amplified titanium:sapphire chains. Multipass and regenerative amplifiers fold the beam many times inside the cavity, and every fold adds an unquantified phase if the mirror has an overcoat. The combination of no overcoat and a low-expansion body is what makes this the standard choice for the folding pair.
  • Polarization-resolved pump-probe and ellipsometry. When the signal depends on the polarization state arriving at the sample, a mirror that transforms that state in a way nobody can calculate is a systematic error that looks like a physical effect.
  • Optical parametric amplifiers and difference-frequency stages. These convert between wavelengths with phase matching that is sensitive to the spectral phase of the pump; a fold with an uncharacterised dielectric term shifts the idler wavelength slightly and unpredictably.
  • CO₂ laser cavities and industrial machining lines. At 10.6 µm the published thresholds apply directly, and the 1000 W/cm CW figure at a 1.18 mm spot is the number to design against for a continuous industrial beam.
  • Broadband infrared beam transport where the source changes. A single 97 percent average across 800 nm to 20 µm lets one fold serve a tuneable source without swapping optics between experiments.
  • Interferometry with large aperture beams. A two-inch mirror with λ/10 figure and a 45.7 mm clear aperture accepts an expanded beam without edge clipping, which is the usual reason a larger substrate is specified at all.

Selection Guide

The choice within the gold group comes down to one question: does the coating have to be immune to handling, or does the light have to be immune to the coating? The table below states the trade in the terms that decide it.

Consideration M03, unprotected gold M01, protected gold
Average reflectance, 800 nm-20 µm 97 percent 96 percent
Dispersion from the coating None Overcoat dispersion present, not published
Polarization fidelity Preserved Changed by an amount that is difficult to quantify
Cleaning Not cleanable, air or nitrogen only Solvent cleaning with normal discipline
Consequence of a fingerprint Permanent local loss and a lower damage threshold Removable in most cases
Right for Sealed, aligned-once systems with strict phase or polarization requirements Shared benches, teaching laboratories, systems that get re-aligned

On aperture, remember that the family offers only three round sizes: Ø1/2 in, Ø1 in and Ø2 in. The two-inch clear aperture of 45.7 mm is generous for an expanded femtosecond beam, where the beam is often 20 to 30 mm after the compressor, and it leaves room for the beam to breathe without touching the rim at 45°. If a drawing specifies a 7 mm or a 30 mm mirror, the answer is not a special order from this family: it is a different product line, or a two-inch optic with an aperture mask.

Series Comparison

The seven coatings on this body are compared below on the two attributes that separate a bare metal from a protected one: whether an overcoat exists, and what that overcoat does to the phase and the polarization of the reflected beam.

Code Coating Spectral Range Average Reflectance Overcoat Phase and Polarization
F01 UV-enhanced aluminum 250-450 nm Ravg 90% MgF₂ Overcoat term present
G01 Protected aluminum 450 nm-20 µm Ravg 90% (450 nm-2 µm), 95% (2-20 µm) SiO₂ Overcoat term present
P01 Protected silver 450 nm-20 µm Ravg 97% (450 nm-2 µm), 95% (2-20 µm) SiO₂ Overcoat term present
M01 Protected gold 800 nm-20 µm Ravg 96% SiO₂ Overcoat term present
M02 MIR enhanced gold 2-20 µm Ravg 98% SiO₂ Overcoat term present
M03 Unprotected gold 800 nm-20 µm Ravg 97% None Metal reflection only
L01 Unprotected gold, line optimised 10.6 µm line Ravg 99% None Metal reflection only

Two members of this table are bare and five are coated, and the two bare ones are the two that an ultrafast or polarization-sensitive system should be choosing between. The L01 is the line specialist: it gives up the broad band to reach 99 percent at 10.6 µm, which is the right trade for a CO₂ cavity and the wrong one for an 800 nm amplifier. The M03 keeps the band and stays at 97 percent, which is why it is the one specified for amplified titanium:sapphire rather than the line-optimised part.

FAQ

Q1. For an ultrafast amplifier, should I take the M01 or the M03?

The M03, unless the bench is shared and gets handled. The argument is not the one percentage point of reflectance; it is that the M01’s overcoat adds a phase term that nobody publishes, and a chirped-pulse amplifier is a system whose entire design depends on knowing every phase term. If you can put the fold pair inside a sealed enclosure and never touch it, the M03 removes an unquantified error from the budget. If the same bench is used by students, gets re-aligned weekly and occasionally has a fingerprint on a mirror, the M01 is the honest choice, because a scratched bare gold mirror has lost more reflectance than the overcoat could ever have cost.

Q2. The published threshold is at 10.6 µm with 100 ns pulses. What does that mean for 800 nm femtosecond pulses?

It means the coating is robust but the number does not transfer. Nanosecond damage at 10.6 µm is thermal: energy is absorbed, heat accumulates, and the film or the substrate fails when the local temperature is high enough. Femtosecond damage at 800 nm happens before heat can move, through multiphoton absorption and avalanche ionization, and the threshold depends on pulse duration and repetition rate in a way that no single number captures. The published 4 J/cm² is good evidence that this is a hard film, and it is not a licence to run any particular fluence at 800 nm. Qualify the part at your own pulse duration.

Q3. How careful do I actually have to be with a bare gold surface?

More careful than with any other optic on the bench, and the discipline is simple enough to state in four words: no solvent, no tissue, no drag. Gold does not oxidise, so the enemy is not air; it is contact. Blow loose dust off with dry nitrogen, handle by the edge with gloves, and if something lands on the surface that nitrogen will not remove, do not try to clean it. A contaminated bare gold mirror can still be used at reduced performance; a wiped one is scrap. Treat the part as a one-time installation: mount it once, align it, and do not touch it again.

Q4. Why is there no Ø7 mm or 30 mm version of this mirror?

Because the family is built around three standard round formats, Ø1/2 in, Ø1 in and Ø2 in, and nothing in between. The two-inch part is the only one with a 12.0 mm body; the smaller two are 6.0 mm thick, which changes both the thermal behaviour and the mounting stiffness. If a design calls for an unusual diameter, the practical options are a two-inch optic with an aperture mask in front of it, or a custom part from a different line, and masking is usually cheaper and faster than a custom coating run.

Q5. Does the missing overcoat mean the mirror is more susceptible to laser damage?

The opposite, according to the published numbers: this coating has the highest thresholds in the family, 4 J/cm² pulsed and 1000 W/cm CW at 10.6 µm, against lower values for every protected coating. A dielectric overcoat is an extra material that can absorb, trap heat against the metal and delaminate. Removing it removes those failure modes. What the overcoat does buy is resistance to handling damage, which is a different risk with a different consequence: laser damage is sudden and obvious, handling damage is gradual and easy to ignore until the throughput has quietly dropped.

Q6. Can I use this mirror with a visible alignment laser?

For finding the beam, yes, and it is common practice to steer a red beam off a gold fold to check the path. For measuring, no: the specification starts at 800 nm and gold’s reflectance falls away below that because of interband absorption, so a 633 nm beam will be noticeably dimmer and the reflectance at that wavelength is not specified. Use the visible beam for alignment only, and do not infer infrared performance from how bright the spot looks.

Usage Precautions

  • No solvent, no tissue, no drag. This is the whole care instruction. Solvents can leave residue in a bare metal surface, tissues abrade it, and dragging converts a cosmetic mark into a permanent scattering defect. Loose dust is removed with clean dry air or dry nitrogen and nothing else.
  • Handle by the ground edge, with gloves, and never touch the coated face. A fingerprint on bare gold is an absorbing organic film in the middle of your beam, and it cannot be cleaned off without damaging the surface around it.
  • Install once and leave it alone. Plan the mount before the optic goes in: a kinematic mount with nylon-tipped retainers, hand-tight, bearing outside the clear aperture. Every subsequent adjustment is a risk event for a surface that cannot be cleaned.
  • Keep the enclosure clean and dry, for contamination reasons rather than chemical ones. Gold will not tarnish, but airborne aerosol and outgassed material from plastics and adhesives will deposit on the surface and stay there. Purge the enclosure if the system runs warm.
  • Do not stack bare gold optics or store them loose. Keep the part in its case, resting off its faces. A single abrasive particle under the weight of a two-inch optic is enough to scratch it, and the scratch is permanent.
  • Verify the beam size against the clear aperture before the first full-power run. The clear aperture is 45.7 mm, and at 45° the footprint stretches by about 1.41 along one axis. A beam that clips the rim loses power and gains a diffraction fringe, and on a bare gold mirror the clipped edge is also the place where contamination accumulates.

Disclaimer

Specifications on this page are compiled from Thorlabs’ publicly published product documentation and are provided for selection reference only. Where this page and the manufacturer’s current official datasheet differ, the datasheet governs. Coatings, specifications and appearance may change without notice. Damage thresholds are measured values under the stated test conditions and are not a guarantee of performance in any particular setup; verifying suitability at your own wavelength, fluence, pulse duration and repetition rate is the user’s responsibility. The pulse-energy and power conversions on this page are arithmetic from published figures, not manufacturer specifications. Prices and lead times are confirmed by our sales team at quotation.

Contact Us

If you are building a chirped-pulse amplifier and want to know whether the fold pair should be bare gold or protected, tell us the pulse duration, the fluence on the optic, the number of passes and how the bench is handled day to day. Those four answers usually settle it.

Hotline: +86 159-2722-0467

E-mail: 859818709@qq.com  |  Website: www.soar-laser.cn

Evaluation units and volume orders are both supported, and the same bare gold coating is available in Ø1/2 in and Ø1 in bodies if the layout needs a matched set.

Reviews

There are no reviews yet.

Be the first to review “Thorlabs PF2011-M03 Ø50.8 mm (2 in) Zerodur® Unprotected Gold Mirror, 800 nm – 20 µm”

Your email address will not be published. Required fields are marked *

中文EN