QQ: 859818709

Thorlabs PF30-03-P01 Ø76.2 mm (3 in) Protected Silver Mirror, 450 nm – 20 µm

Thorlabs PF30-03-P01 Ø76.2 mm (3 in) Protected Silver Mirror, 450 nm – 20 µm

Price on request
Category:

Description

Product Overview

The PF30-03-P01 is the 3 inch member of the Thorlabs protected silver mirror family: a round mirror with a nominal diameter of 76.2 mm, a protected silver coating covering 450 nm to 20 um, an average reflectance of 97 percent from 450 nm to 2 um and 95 percent from 2 um to 20 um, a fused silica substrate, a surface flatness of lambda/10 at 633 nm, a surface quality of 40-20 scratch-dig, and a clear aperture of 90 percent of the diameter. It is a Customer Inspired item, which in practice means the part is built to order against the published drawing rather than pulled from a shelf, and Thorlabs quotes roughly two weeks. The part number is laser engraved on the back of the mirror, so a mirror that has been separated from its packaging can still be identified.

The single most useful fact about this mirror is one that buyers of large optics rarely hear stated plainly: the coating specification does not get better as the diameter grows. The reflectance figures, the 40-20 surface quality, the lambda/10 flatness and the laser damage thresholds on the 3 inch part are the same values published for the smaller diameters in the same coating family. Thorlabs states explicitly that the damage threshold specifications are constant for this coating type, regardless of the size or shape of the mirror. So the money spent on a 3 inch mirror does not buy a better coating. It buys area, and it buys the mechanical stiffness that a large substrate brings with it.

That reframing matters because it moves the engineering question. On a 1 inch mirror the coating is the limiting factor and the mount is an afterthought. On a 3 inch mirror the coating is already as good as it will get, and the limiting factors become the substrate and the way it is held. Three quantities scale badly with diameter. The optical area grows with the square of the diameter, so a 3 inch mirror carries 2.25 times the area of a 2 inch mirror, but self-weight deflection under gravity grows with the fourth power of the diameter for a given thickness, which is a factor of 3.16 between the 2 inch and 3 inch parts at equal thickness. The clamp load from a retaining ring, concentrated at a few contact points, produces local bending whose contribution to the total wavefront error also grows with diameter. And lambda/10 is an absolute requirement, not a relative one: the same 63.3 nm of permitted deviation spread across a 76.2 mm aperture corresponds to a smaller slope error than the same deviation spread across a 25.4 mm aperture, which is why large flat mirrors are harder to make and why a large mirror that meets lambda/10 is genuinely a different object from a small one that meets it.

The clear aperture is the number to design the beam around. At 90 percent of the diameter the usable area is 68.6 mm across, and everything outside that is edge that the specification does not cover. A beam of 50 mm diameter therefore sits comfortably inside the clear aperture with 9 mm of margin on each side, while a 65 mm beam is already touching the edge. For a beam that is being folded after expansion, the useful rule is to keep the beam at or below two thirds of the clear aperture, which on this mirror means 45 mm, so that a small pointing drift does not walk the beam onto the unfinished edge.

The substrate is fused silica rather than a lower grade glass, and on a mirror this size that is not a cosmetic choice. A 3 inch by 19.1 mm disc of fused silica has a volume of about 87 cubic centimetres and a mass of about 192 grams. That mass has to be carried by whatever holds the mirror, and the substrate has to resist bending under its own weight between the support points. Fused silica gives a low coefficient of thermal expansion, no measurable absorption in the visible, and enough hardness to take a good polish over a large aperture.

Key Features

  • Protected silver coating, 450 nm to 20 um. The highest average reflectance of any metal coating over this range: 97 percent average from 450 nm to 2 um and 95 percent average from 2 um to 20 um.
  • Coating specification identical across the family. Same reflectance, same 40-20 surface quality, same lambda/10 flatness and same damage thresholds as the smaller diameters, so upsizing does not change the optical performance per unit area.
  • Damage thresholds valid at any size. Thorlabs states that the damage threshold specifications are constant for this coating type regardless of the size or shape of the mirror. A buyer does not have to re-qualify the coating when moving from a 1 inch to a 3 inch part.
  • 0.225 J/cm2 at 800 nm, 99 fs, 1 kHz, 0.167 mm spot. The femtosecond figure for this coating, measured on a small spot and therefore applicable to a scanned or focused beam rather than to a large collimated one.
  • 1 J/cm2 at 1064 nm, 10 ns, 10 Hz, 1.010 mm spot. The nanosecond figure, which is the one that matters for most Nd:YAG and fibre work at 1064 nm.
  • CW limits of 500 W/cm at 1.07 um and 1500 W/cm at 10.6 um. Quoted per centimetre of beam diameter, not per square centimetre, because continuous damage in a metal film is driven by linear power density along the spot edge.
  • Fused silica substrate, 19.1 mm nominal thickness. Low thermal expansion, high hardness, and enough section stiffness to keep self-weight deflection small across a 76.2 mm span.
  • Lambda/10 at 633 nm and 40-20 scratch-dig. A flatness figure that is absolute, so the permitted slope error falls as the aperture grows, and a surface quality that tolerates inspection under a hand-held illuminator without argument.
  • Roughly 100 nm of silicon dioxide overcoat. Thin enough not to shift the reflectance curve appreciably, thick enough to let the mirror be cleaned with solvent and lens tissue.
  • Item number laser engraved on the back. Every size in the family except the 7 mm and the 35 by 52 mm parts carries its part number, which matters once several mirrors are out of their packaging on the same bench.
  • 90 percent clear aperture. 68.6 mm of usable diameter, with the outer 10 percent reserved as mounting and handling edge.
  • Two week nominal lead time. Built to order, so the purchase order date rather than the ship date is what a project schedule has to be built around.

Technical Specifications

Parameter Specification
Model PF30-03-P01
Coating type Protected silver (silver film with dielectric overcoat)
Wavelength range 450 nm to 20 um
Average reflectance, 450 nm to 2 um 97%
Average reflectance, 2 um to 20 um 95%
Substrate Fused Silica
Diameter 76.2 mm (3.0 in)
Diameter tolerance +0.0 mm / -0.1 mm
Thickness 19.1 mm (0.75 in) nominal, see note below
Thickness tolerance plus or minus 0.2 mm
Clear aperture 90% of Diameter, i.e. 68.6 mm usable
Surface flatness (P-V) lambda/10 at 633 nm
Surface quality 40-20 Scratch-Dig
Overcoat Silicon dioxide, approximately 100 nm thick
Back surface Laser engraved with the item number
Pulsed LIDT, 800 nm 0.225 J/cm2 (99 fs, 1 kHz, 0.167 mm spot)
Pulsed LIDT, 1064 nm 1 J/cm2 (10 ns, 10 Hz, 1.010 mm spot)
CW LIDT, 1.07 um 500 W/cm (0.974 mm spot)
CW LIDT, 10.6 um 1500 W/cm (0.339 mm spot)
Damage threshold scaling Constant for this coating type regardless of mirror size or shape
Product status Customer Inspired, built to order
Nominal lead time Approximately 2 weeks
Computed area of the coated face 4560.4 mm2
Computed mass at nominal thickness Approximately 192 g (fused silica at 2.2 g/cm3)

Note on thickness: 19.1 mm (0.75 in) is the nominal value listed for this diameter in the official series table, which presents the thickness as a shared column across the large diameters. Confirm the thickness against the current official spec sheet before mechanical, mount or clearance design, because a retaining ring cut for 19.1 mm will not close on a part that differs by the full tolerance band. Area and mass in the last two rows are calculated from the stated diameter and nominal thickness, not taken from the datasheet.

Applications

Folding a beam after expansion. This is the main reason a 3 inch mirror gets bought. A beam expanded to 50 mm for a longer collimation length has to be redirected somewhere, and the fold is usually the largest optic in the system. Because the coating carries the same specification as the small mirrors upstream, the fold does not become the weak link in the chain: the wavefront error budget stays flat through the fold instead of stepping up at the biggest component.

Large aperture interferometry. In a Twyman-Green or Fizeau layout built around a 100 mm test beam, the reference and test arms both need folds that do not add coma. A lambda/10 flat at 633 nm keeps the mirror’s own contribution to the fringe field small, and the fused silica substrate keeps that contribution stable when the room temperature moves. On a large aperture the mounting is usually a bigger error source than the mirror, which is why the mount deserves as much attention as the optic.

Exit fold on a collimator or beam expander. The output of a large collimator is a wide, low divergence beam that has to be aimed at a target far away. The fold sits at the end of the tube, where there is no room to stop down the beam, so the full aperture is used. Here the clear aperture figure is what decides whether the mirror is big enough, not the nominal diameter.

Scanning and beam delivery systems needing a stiff substrate. Where a large mirror is moved, or where the whole assembly is subject to vibration, a 19.1 mm fused silica disc behaves far better than a thin plate of the same diameter. The added mass is a cost in the actuator budget but a benefit in the figure of the mirror surface: a stiffer substrate deflects less between its support points, so the flatness measured on the test stand survives the trip onto the machine.

Multi-wavelength benches that share one fold. A metal coating covering 450 nm to 20 um lets one mirror serve a visible alignment laser, a 1064 nm working beam and a mid-infrared probe at the same time. On a bench where several sources are combined, replacing three dielectric mirrors with one protected silver fold removes three alignment degrees of freedom and three chances for a coating to be wrong for one of the wavelengths.

Selection Guide

The order of the decisions matters, because the first one eliminates most of the catalogue and the last one is where most projects actually go wrong.

  • Step 1, fix the wavelength range. Protected silver is the default from 450 nm to 20 um. Above roughly 800 nm a protected gold coating gives higher reflectance and is worth the premium. In the ultraviolet, use a UV enhanced aluminium. Beyond 2 um in the mid-infrared, an enhanced gold is the better choice. Silver is the right answer only when the band genuinely spans the visible and the near-infrared at once.
  • Step 2, size from the clear aperture, not the diameter. Take the largest beam diameter the fold will ever see, add the pointing drift, and divide by 0.9. A 50 mm beam with 5 mm of drift needs 61 mm of clear aperture, which means a nominal diameter of 68 mm, so the 3 inch part is the correct size and a 2 inch part is not.
  • Step 3, decide whether the substrate has to carry load. If the mirror is simply dropped into a ring and left alone, substrate stiffness is a minor term. If the mirror is the largest optic in a vibrating system, or if it is supported at only three points, the 19.1 mm fused silica section is doing real work and should be treated as a structural element.
  • Step 4, plan the mount before ordering. A 192 gram disc clamped by a ring will be distorted by the ring. Decide in advance whether the mount uses a full circumference retaining ring with a soft interface, three-point edge support, or a kinematic back plate. The mirror cannot fix a mount that pinches it.
  • Step 5, book the lead time. This is a Customer Inspired item with a nominal two week lead time. On a project with a fixed installation date, the mirror should be ordered with the mount, not after the mount has been machined and found to be the wrong size.

One further point on sizing, because it is the mistake that shows up most often in enquiries. Buyers frequently specify a mirror by the beam diameter they intend to use, then discover that the clear aperture is 90 percent of the nominal diameter and that their 70 mm beam will not fit on a 76.2 mm mirror. The correct sequence is to start from the clear aperture and work back to the nominal diameter, and to leave at least 20 percent of the clear aperture unused so that a small realignment does not put energy on the unpolished edge.

Series Comparison

Model Diameter Clear aperture at 90% Coated area Typical role
Ø1 in member of the family 25.4 mm 22.9 mm 507 mm2 Compact folds, alignment beams, breadboard scale
PF20-03-P01 50.8 mm (2.0 in) 45.7 mm 2027 mm2 General purpose folds, 30 mm to 40 mm beams
PF30-03-P01 (this page) 76.2 mm (3.0 in) 68.6 mm 4560 mm2 Expanded beams, large aperture interferometry
PF40-03-P01 101.6 mm (4.0 in) 91.4 mm 8107 mm2 Widest round option, near 90 mm beams

Every row carries the same coating: 450 nm to 20 um, 97 percent average from 450 nm to 2 um, 95 percent average from 2 um to 20 um, 40-20 scratch-dig, lambda/10 at 633 nm, and the same damage thresholds. The differences between rows are geometric. Moving from 2 inch to 3 inch doubles the coated area to 2.25 times, and the mass at the 19.1 mm nominal thickness goes from a value that a small kinematic mount can ignore to roughly 192 grams that it cannot. Moving from 3 inch to 4 inch multiplies the area by a further 1.78 and the mass to roughly 341 grams. The 3 inch part is the point in the family where the optic stops being a component and starts being a structure, which is exactly why it is specified with a 19.1 mm section.

Diameters and clear apertures above are from the published family specification. Mass is calculated only for the two sizes whose nominal thickness appears in the series table; confirm the thickness of the smaller members on their own spec sheets before comparing weights.

FAQ

Q: Is the coating on the 3 inch mirror better than on the 2 inch version?

A: No. It is the same coating with the same published values: 97 percent average from 450 nm to 2 um, 95 percent average from 2 um to 20 um, 40-20 scratch-dig, lambda/10 at 633 nm, and identical laser damage thresholds. Thorlabs states that the damage threshold specifications are constant for this coating type regardless of the size or shape of the mirror. What changes with diameter is the area, the mass and the stiffness of the substrate, not the optical quality per unit area.

Q: Why does lambda/10 cost so much more on a large mirror?

A: Because lambda/10 is an absolute figure. At 633 nm it permits 63.3 nm of peak-to-valley deviation across the whole aperture. Spread over 76.2 mm that is a much smaller angular slope than the same 63.3 nm spread over 25.4 mm, so the polishing process has to hold a tighter slope over three times the distance. Add the larger tool, the longer polishing time and the greater sensitivity to substrate stress, and the price difference stops looking unreasonable.

Q: What beam diameter can this mirror actually take?

A: The clear aperture is 90 percent of the diameter, so 68.6 mm. A collimated beam of 50 mm fits with margin. For a beam that will be realigned occasionally, keep the beam at or below two thirds of the clear aperture, which is about 45 mm, so that pointing drift does not walk the beam onto the unpolished edge. If the beam is focused at the mirror, use the spot size at the mirror surface, not the beam size at the last lens.

Q: Can this mirror be used with a femtosecond laser?

A: Yes, within the published limit: 0.225 J/cm2 at 800 nm with 99 fs pulses at 1 kHz and a 0.167 mm spot. That figure is measured on a small spot, which is the relevant geometry for a focused or scanned beam. For a large collimated femtosecond beam the fluence calculation has to be done on the actual spot at the mirror and compared against the same limit, and the usual practice is to stay well below it because the measurement is statistical rather than deterministic.

Q: What continuous power can it handle at 1064 nm?

A: The published CW figure for this coating is 500 W/cm at 1.07 um with a 0.974 mm spot. That is power per centimetre of beam diameter, not power per square centimetre, so a 10 mm diameter beam corresponds to a limit of 500 W and a 20 mm beam to 1000 W, subject to the usual safety margin. At 10.6 um the figure rises to 1500 W/cm with a 0.339 mm spot.

Q: Is the back of the mirror polished?

A: No. The back carries the laser engraved item number and is not an optical surface. Treat it as a mechanical face: it is what the mount bears on, and it should not be used as a reference flat without checking the drawing first.

Q: How should the mirror be held without distorting it?

A: Distribute the load. A full circumference retaining ring tightened against a soft interface, or a three-point edge support with the load taken on the cylindrical edge rather than the polished face, both work. What does not work is a ring tightened until it feels firm: on a 19.1 mm fused silica disc that is enough to print a ring-shaped error into the reflected wavefront. Tighten until the mirror is captive, then stop.

Usage Precautions

  • Keep humidity low, and keep it low permanently. Thorlabs states that although the overcoat helps to protect silver from tarnishing, high humidity environments should be avoided, and that silver mirrors should be used and stored in areas at room temperature with minimal humidity. This is not a handling note for the day of installation; it is a storage condition for the life of the part.
  • Do not touch the coated face or the edges. Fingerprints, contact with abrasive surfaces, and environments with high humidity or temperature will diminish the effectiveness of the protective overcoat, leaving the silver coating susceptible to oxidation and degradation. Latex gloves or similar protective coverings are recommended, and even with those precautions the mirrored face and the edges should not be touched.
  • Handle a 3 inch disc with two hands. At roughly 192 grams and 76.2 mm across, this is the size at which a one-handed pick-up by the edge becomes a real risk. A dropped mirror does not fail gracefully.
  • Clean with solvent and lens tissue only. The published cleaning tutorial for Thorlabs optics permits reagent grade acetone or isopropanol with lens tissue. Do not use household cleaners, abrasive wipes or any cloth that has been washed with fabric softener; the overcoat is about 100 nm thick and a mechanical scratch goes straight through it into the silver.
  • Do not let solvent pool at the edge. On a coated silver mirror the edge is where the overcoat terminates, and it is where capillary action will hold a droplet. Wick it away with dry lens tissue and let the part come to room temperature before bagging it.
  • Support the mirror on its edge, not its face. Any fixture that presses on the polished face introduces local bending. On a 3 inch substrate the resulting wavefront error is larger than on a small mirror because the same local load acts over a longer span.
  • Store in the original packaging. The packaging is designed for a 76.2 mm disc. A drawer, a foam-lined box or a plastic bag is not, and a mirror stored loose will eventually be scratched by whatever shares the drawer.

Disclaimer

The optical and mechanical values on this page are compiled from the publicly published Thorlabs specification for the PF30-03-P01 and are offered to support selection. Where this page and the current official spec sheet disagree, the spec sheet governs. Coating performance, damage thresholds and mechanical dimensions may be revised without notice, and the area and mass figures shown here are calculations from the published diameter and nominal thickness rather than manufacturer values. No price is stated on this page; price, availability and lead time are confirmed at quotation. A project that depends on the mirror surviving a specific fluence should qualify the coating on its own beam rather than relying on a catalogue figure.

Two values are deliberately absent from this page. No parallelism or wedge figure is quoted, because none is published for this part, and no back surface specification is given beyond the engraved item number, because the back is a mechanical face rather than an optical one. A design that needs either callout should be checked against the current drawing rather than against a summary. The thickness in the table is likewise the nominal series value, not a measured dimension, and a mount cut to a tolerance tighter than the plus or minus 0.2 mm band should be verified against the delivered part.

Contact Us

For a check on whether a 3 inch fold is the right size for a given beam, for the current thickness confirmation before a mount is machined, or for a quantity quotation on several mirrors, contact the sales team with the beam diameter at the mirror, the wavelength range, the pulse duration and repetition rate if pulsed, and the intended mounting method. Supplying the beam diameter and the wavelength band together is usually enough to answer the sizing question in one reply.

A request that includes a sketch of the mount, or a photograph of the existing holder with the mirror in place, is usually answered in one exchange. A request that includes only a part number and a quantity takes longer, because the first reply has to establish what the mirror will be clamped by, and the clamping method is what decides whether the delivered wavefront matches the specification.

Reviews

There are no reviews yet.

Be the first to review “Thorlabs PF30-03-P01 Ø76.2 mm (3 in) Protected Silver Mirror, 450 nm – 20 µm”

Your email address will not be published. Required fields are marked *

中文EN