QQ: 859818709

Thorlabs PF40-03-P01 Ø101.6 mm (4 in) Protected Silver Mirror, 450 nm – 20 µm

Thorlabs PF40-03-P01 Ø101.6 mm (4 in) Protected Silver Mirror, 450 nm – 20 µm

Price on request
Category:

Description

Product Overview

PF40-03-P01 is the largest round mirror in the Thorlabs protected silver range: 101.6 mm in diameter, a silver film under a dielectric overcoat covering 450 nm to 20 um, 97 percent average reflectance from 450 nm to 2 um and 95 percent average from 2 um to 20 um, on a fused silica substrate 19.1 mm nominal in thickness, flat to lambda/10 at 633 nm and finished to 40-20 scratch-dig, with a clear aperture of 90 percent of the diameter. There is no round mirror above it in this coating family. That single sentence is the most important thing on this page, because it converts a specification question into a procurement question: the choice is not between a 4 inch mirror and a better 4 inch mirror, it is between a 4 inch mirror and a different geometry entirely.

Above 101.6 mm the same coating is offered in square formats, and that is a different question rather than a bigger answer. PFSQ20-03-P01 is a 2 by 2 inch square: 50.8 mm on a side, about 2581 mm2 of coated area and a 71.8 mm diagonal, which is roughly a third of the area of the round 4 inch part. It earns its place when the beam is genuinely rectangular and the corners of a round mirror would be wasted glass. It is not a substitute for a 101.6 mm round aperture. A project that needs a round aperture larger than this mirror is looking at a custom optic, with custom lead time, custom price and custom risk, and should establish that early rather than after the mount has been designed.

The clear aperture sets the real limit. Ninety percent of 101.6 mm is 91.4 mm of usable diameter, and the outer 5.1 mm of radius is handling and mounting edge that the published flatness does not cover. If the beam that has to be folded is 70 mm across, then a 3 inch mirror with 68.6 mm of clear aperture is already marginal and a 4 inch mirror is comfortable but oversized. If the beam is 85 mm or 90 mm, the 4 inch part is the only round answer and the question of whether it is worth the price does not arise, because there is nothing to compare it against.

The commercial detail that decides project schedules: this is a Customer Inspired item. It is not a stock catalogue line that a distributor keeps on a shelf. Thorlabs quotes roughly two weeks, and that clock starts when the order is released, not when the enquiry is sent. On a build where the mirror is the last optic to be installed, two weeks is comfortable; on a build where the mirror is needed to alignment-test the mount that is being machined, two weeks is the critical path. Lock the purchase order early and treat the delivery date as a constraint rather than a hope.

One design note that applies at this size and not at smaller ones. A 101.6 mm by 19.1 mm disc of fused silica has a volume of about 155 cubic centimetres and a mass of roughly 341 grams. A mount that carries 341 grams with a single central screw and no counter-support will sag, and the sag will be visible in the wavefront as astigmatism that changes when the mount is rotated. The mirror cannot be blamed for this. The mount has to be designed for the mass, which at this diameter usually means three-point edge support or a back plate with a distributed interface.

Key Features

  • The ceiling of the round protected silver range. 101.6 mm is the largest diameter offered in this coating family. Above it there is no larger round mirror in this coating: the 2 by 2 inch square PFSQ20-03-P01 is a smaller aperture in a different shape, so a wider round beam means a custom optic.
  • 91.4 mm of clear aperture. Ninety percent of the diameter, which is the number that decides whether a wide collimated beam fits, not the 101.6 mm nominal figure.
  • 97 percent average reflectance from 450 nm to 2 um. The visible and near-infrared figure, and the highest average of any metal coating over that span.
  • 95 percent average reflectance from 2 um to 20 um. The mid-infrared figure, which is what makes a single mirror usable across a thermal imaging or CO2 laser band as well.
  • Coating values do not improve with size. The reflectance, the 40-20 finish, the lambda/10 flatness and the damage thresholds are the same as on the 1 inch and 2 inch members. Thorlabs states that damage threshold specifications are constant for this coating type regardless of the size or shape of the mirror.
  • 1 J/cm2 at 1064 nm, 10 ns, 10 Hz, 1.010 mm spot. The nanosecond limit, unchanged from the small diameters, so a wide beam does not require a different coating qualification.
  • 1500 W/cm at 10.6 um, 0.339 mm spot. The continuous limit in the mid-infrared, quoted per centimetre of beam diameter.
  • 19.1 mm fused silica section. About 341 grams of substrate, stiff enough that self-weight deflection between support points stays small but heavy enough that the mount must be designed for it.
  • Lambda/10 at 633 nm, 40-20 scratch-dig. An absolute flatness tolerance across a 101.6 mm span, which is a considerably tighter slope requirement than the same tolerance on a small mirror.
  • Item number laser engraved on the back. At this diameter several mirrors may be out of their crates at once during a build, and the engraving is what stops them being confused.
  • Roughly 100 nm silicon dioxide overcoat. Enough to allow solvent cleaning, thin enough that the reflectance curve is essentially the bare silver curve.
  • Customer Inspired, roughly two weeks. Built to order rather than stocked, which is a schedule input rather than a shipping detail.

Technical Specifications

Parameter Specification
Model PF40-03-P01
Coating type Protected silver, silver film with dielectric overcoat
Spectral range 450 nm to 20 um
Average reflectance, 450 nm to 2 um 97%
Average reflectance, 2 um to 20 um 95%
Substrate material Fused Silica
Diameter 101.6 mm (4.0 in)
Diameter tolerance +0.0 mm / -0.1 mm
Thickness 19.1 mm (0.75 in) nominal, see note below
Thickness tolerance plus or minus 0.2 mm
Clear aperture 90% of Diameter, i.e. 91.4 mm usable
Surface flatness (P-V) lambda/10 at 633 nm
Surface quality 40-20 Scratch-Dig
Overcoat thickness Approximately 100 nm of silicon dioxide
Back surface marking Item number laser engraved
Pulsed LIDT, 800 nm 0.225 J/cm2 (99 fs, 1 kHz, 0.167 mm spot)
Pulsed LIDT, 1064 nm 1 J/cm2 (10 ns, 10 Hz, 1.010 mm spot)
CW LIDT, 1.07 um 500 W/cm (0.974 mm spot)
CW LIDT, 10.6 um 1500 W/cm (0.339 mm spot)
Damage threshold scaling Constant for this coating type regardless of mirror size or shape
Ordering status Customer Inspired, built to order
Nominal lead time Approximately 2 weeks
Coated area, calculated 8107.3 mm2
Mass at nominal thickness, calculated Approximately 341 g at 2.2 g/cm3

Note on thickness: 19.1 mm (0.75 in) is the nominal figure for this diameter in the official series table, where thickness appears as a merged column across the large diameters. Confirm it against the current spec sheet before cutting a retaining ring or a back plate, because a ring machined to 19.1 mm nominal will not close on a part at the negative end of the plus or minus 0.2 mm band. The area and mass rows are calculated from the stated diameter and nominal thickness and are not datasheet values.

Applications

Steering a wide collimated beam. A beam expanded to 80 mm or 90 mm for a long propagation distance needs a fold that is wider than the beam by a comfortable margin. At 91.4 mm of clear aperture this is the last round size that can do that job, and the fold is usually the single largest component in an otherwise modest optical train.

Large area interferometric measurement. When the test aperture itself is 80 mm or more, both arms of the interferometer need folds that do not add curvature. Lambda/10 at 633 nm over a 101.6 mm span is a demanding figure, and it is the reason this part is chosen over a plate mirror: a plate of the same diameter will not hold that flatness under its own weight.

End of a collimator or beam expander. The output fold of a large collimator sees the full expanded beam with no aperture to stop it down. Here the clear aperture is used almost entirely, and the 5.1 mm ring outside it is the only margin available. Mount design has to keep clamps and retaining features off that ring if the beam is close to the limit.

Cross-table beam transport on a large optical platform. On a 1.5 m or 3 m table, moving a beam from one end to the other at height takes several folds, and every fold costs throughput. A protected silver coating at 97 percent average is the reason metal is preferred over a dielectric stack for broadband transport: the loss per bounce is predictable and flat across the band, so the budget can be computed once rather than per wavelength.

Shared fold for mixed visible and thermal sources. One mirror covering 450 nm to 20 um lets a visible alignment laser and a mid-infrared source use the same fold without a second optic and a second alignment. On a large aperture system, removing one fold from the layout is worth more than the small reflectance difference between coating types.

Selection Guide

Work through this as a stop-rule sequence. Most enquiries about a 4 inch mirror end at step 2, and ending there is the correct outcome, not a lost sale.

  • Step 1, measure the beam at the mirror, not at the laser. The diameter that matters is the one at the coated surface, including any divergence over the path and any pointing drift. A beam that is 60 mm at the laser can easily be 85 mm at a fold two metres downstream.
  • Step 2, compare that figure against 91.4 mm, not 101.6 mm. If the beam is 70 mm or less, a 3 inch mirror with 68.6 mm of clear aperture is at its limit and a 4 inch mirror is the comfortable choice, but a 3 inch part with a re-optimised beam path may be cheaper. If the beam is under 60 mm, the 2 inch part is the sensible purchase and the 4 inch part is wasted money.
  • Step 3, if the beam is above 91 mm, change geometry rather than diameter. There is no larger round mirror in this coating family. The square PFSQ20-03-P01 is 2 by 2 inches with a 71.8 mm diagonal, so it suits a rectangular beam envelope but does not replace a 101.6 mm round aperture. Anything wider is a custom optic.
  • Step 4, decide whether the coating band is really 450 nm to 20 um. If the work is entirely above 800 nm, a protected gold coating returns more per bounce and is worth the premium. Silver earns its place when the visible and the near-infrared have to share one optic.
  • Step 5, design the mount for 341 grams before ordering. Three-point edge support or a distributed back interface. A single central screw on a disc this size produces astigmatism that will be attributed to the mirror and will not be the mirror.
  • Step 6, release the order early. Two weeks nominal, built to order. If the mirror is needed to qualify a mount, order the mirror and the mount blank together.

The honest version of the sizing advice, stated plainly: if a 2 inch or 3 inch mirror will do the job, it is the better purchase on both price and lead time, and there is no optical performance penalty for choosing it. The coating values on PF20-03-P01 and PF30-03-P01 are the same as on this part. The 4 inch mirror is the right answer only when the beam genuinely needs more than about 70 mm of clear aperture, and at that point it is not a premium, it is the only option.

Series Comparison

Model Geometry Clear aperture Coated area Where it fits
PF20-03-P01 Round, 50.8 mm 45.7 mm 2027 mm2 General folds, beams up to about 35 mm
PF30-03-P01 Round, 76.2 mm 68.6 mm 4560 mm2 Expanded beams, beams up to about 50 mm
PF40-03-P01 (this page) Round, 101.6 mm 91.4 mm 8107 mm2 Wide beams, beams up to about 70 mm
PFSQ20-03-P01 Square, 2 by 2 in 71.8 mm diagonal About 2581 mm2 Rectangular beams; a smaller aperture than the round 4 in part

The area progression is worth keeping in mind as a ratio rather than a set of absolute numbers. Going from 2 inch to 3 inch multiplies the coated area by 2.25; going from 3 inch to 4 inch multiplies it by a further 1.78. The step from 3 inch to 4 inch therefore buys less additional area than the step below it, while adding a great deal more mass and a mount that has to be engineered. That is the structural reason the 4 inch part is a specialist choice rather than a default upgrade.

Throughput is the other number that changes at this scale, because large aperture systems usually have more folds than small ones. The table below shows cumulative reflectance for a chain of identical protected silver bounces, using the published average figures for this coating.

Number of protected silver bounces Cumulative throughput, 450 nm to 2 um Cumulative throughput, 2 um to 20 um
1 bounce 97.0% 95.0%
2 bounces 94.1% 90.3%
4 bounces 88.5% 81.5%
6 bounces 83.3% 73.5%

The comparison that matters is against a lower grade reflective surface. Six bounces at 97 percent average leaves 83.3 percent of the input; six bounces at 90 percent leaves 53.1 percent. The gap is 30 percentage points, which on a system already fighting for signal is the difference between a workable measurement and an unworkable one. On a broadband transport path, the coating specification is worth more than the extra diameter, which is a further argument for not oversizing the mirror.

FAQ

Q: Is 101.6 mm really the largest round mirror available in this coating?

A: It is the largest round diameter in the Thorlabs protected silver family. The same coating is offered on square formats such as PFSQ20-03-P01 at 2 by 2 inches, but a 50.8 mm square with a 71.8 mm diagonal is a smaller aperture than this mirror, so a square part is a different shape rather than a larger one. A round aperture wider than 101.6 mm is a custom order. If a project needs a round aperture larger than 101.6 mm, plan for a custom part and its lead time rather than searching for a catalogue number.

Q: Would a 3 inch mirror do the same job for less?

A: If the beam is 70 mm or narrower, usually yes. PF30-03-P01 gives 68.6 mm of clear aperture and carries exactly the same coating values, the same 40-20 finish, the same lambda/10 flatness and the same damage thresholds. The 4 inch part earns its price only when the beam needs more than about 70 mm of clear aperture, or when a wide beam must be folded with enough margin that realignment never puts energy on the edge.

Q: How much does the mirror weigh, and does the mount need to be special?

A: Roughly 341 grams at the 19.1 mm nominal thickness, calculated from the 8107 mm2 area and a fused silica density of 2.2 g/cm3. That is enough mass that a single central screw without counter-support will allow the disc to sag and will print astigmatism into the reflected wavefront. Three-point edge support, or a back plate with a distributed compliant interface, is the usual solution.

Q: Why does the damage threshold not scale with the mirror size?

A: Because it is a property of the coating process, not of the substrate area. Thorlabs states that the damage threshold specifications are constant for this coating type regardless of the size or shape of the mirror. The practical consequence is convenient: a coating qualified on a 1 inch witness part can be specified on a 4 inch part without a new qualification campaign, provided the beam geometry at the mirror is used for the fluence calculation.

Q: What is the lead time and why is it not a stock item?

A: Approximately two weeks, because the part is Customer Inspired and built to order. Large substrates are not held in quantity, and polishing a lambda/10 flat across 101.6 mm takes time regardless of demand. Treat the two weeks as a schedule input: order before the mount is finished, not after.

Q: Can it be used at 10.6 um?

A: Yes. The coating covers 2 um to 20 um at 95 percent average reflectance, and the published continuous limit at 10.6 um is 1500 W/cm with a 0.339 mm spot. The figure is power per centimetre of beam diameter, so a 10 mm beam corresponds to 1500 W before any safety margin is applied.

Q: Does the mirror come with a mount?

A: No. It is supplied as an unmounted optic with the item number engraved on the back. Mounts for a 101.6 mm disc are a separate selection, and the mount rather than the mirror usually sets the achievable wavefront quality at this size.

Usage Precautions

  • Humidity is the enemy of a silver coating. Thorlabs states that although the overcoat helps to protect silver from tarnishing, high humidity environments should be avoided, and that silver mirrors should be used and stored in areas at room temperature with minimal humidity. A 4 inch part represents a substantial investment and a long lead time; store it accordingly.
  • Never touch the face or the edge with bare hands. Fingerprints, contact with abrasive surfaces, and environments with high humidity or temperature will diminish the effectiveness of the protective overcoat, leaving the silver coating susceptible to oxidation and degradation. Latex gloves or similar protective coverings are recommended, and even with those precautions care should be taken not to touch the mirrored face or edges.
  • Two hands, always. At 101.6 mm and roughly 341 grams this is not a part to lift by one edge over a concrete floor. Have the mount open and ready before the mirror leaves its packaging.
  • Clean only with reagent grade solvent and lens tissue. Acetone or isopropanol as permitted by the published Thorlabs optic cleaning tutorial, applied with lens tissue, never with household cleaners, abrasive wipes or a cloth that has been through a washing machine. The overcoat is about 100 nm thick.
  • Do not store it standing on edge without support. A 341 gram disc leaning against a shelf will eventually slide, and the edge chip that results is not repairable.
  • Keep the retaining ring off the clear aperture. With only 5.1 mm of radius outside the 91.4 mm clear aperture, a retaining feature that intrudes even slightly is inside the beam. Check the mount drawing against the clear aperture before assembly.
  • Check flatness after mounting, not before. The wavefront figure that matters is the one measured in the mount. If it degrades after installation, the cause is the support geometry, and loosening the clamps to see whether the figure recovers is a two-minute diagnostic worth doing.

Disclaimer

Specifications here are summarised from the manufacturer published data for PF40-03-P01 and are intended for selection work. The current official spec sheet prevails over this page in every case of conflict. Reflectance values are averages over the stated bands and are not guarantees at a single wavelength; damage thresholds are measured values with statistical spread and should be treated as guidance rather than as a hard operating limit. Area, mass and cumulative throughput figures on this page are calculations performed from the published diameter, nominal thickness and average reflectance, and are not manufacturer specifications. No price is quoted here.

Two figures are missing on purpose. There is no parallelism specification, because none is published for this coating family, and there is no transmission data, because a reflectance specification does not imply one. A system model that needs either should be built from the current drawing and from measured reflectance data for the delivered batch rather than from an average quoted over a two-decade band. The thickness entry is the nominal series value, and the mass figure is calculated from it, so a mount designed to a tight tolerance should be checked against the part that actually arrives.

Contact Us

If a project is close to the 91.4 mm clear aperture limit, send the beam diameter at the mirror and the distance to the next optic and the sales team will confirm whether this part or the square alternative is the better fit. For orders, state the quantity, the required delivery date and whether the mirror will be mounted on arrival; where a delivery date is tight, say so at enquiry stage so that the two week build window can be checked against the current schedule rather than assumed.

Where the mirror is part of a tender or a fixed-price project, state the required delivery date at enquiry rather than at order. A two week build window that starts on the order date is comfortable in most schedules and uncomfortable in a few, and the difference is decided by when the question is asked. Enquiries that name the beam diameter at the mirror and the size of the breadboard it will sit over are answered fastest, because those two numbers settle both the diameter and the mount.

Reviews

There are no reviews yet.

Be the first to review “Thorlabs PF40-03-P01 Ø101.6 mm (4 in) Protected Silver Mirror, 450 nm – 20 µm”

Your email address will not be published. Required fields are marked *

中文EN