QQ: 859818709

Thorlabs PFA51502 Active Isolation Breadboard Support Frame, 700 mm Height, 900 x 1500 mm

Thorlabs PFA51502 Active Isolation Breadboard Support Frame, 700 mm Height, 900 x 1500 mm

Price on request
Category:

Description

Product Overview

PFA51502 is an active isolation breadboard support frame, 700 mm (27.5 in) high, matched to a 900 x 1500 mm (36 in x 60 in) breadboard. It carries up to 700 kg (1,545 lbs) on four independent, air mounted, active vibration isolators. The isolators are self-leveling by pneumatic means, with a leveling repeatability of ±0.25 mm (0.010 in). The vertical resonant frequency is below 1.6 Hz and the horizontal resonant frequency is below 1.2 Hz. The structure is all steel. Leveling pads give plus or minus 9.5 mm (plus or minus 0.375 in) of height adjustment and the leveling feet give ±5 mm (plus or minus 0.2 in). An optional caster set, PWA061, makes the frame movable.

The number to look at first is not a transmission figure. It is just under 1.6 Hz. A vibration isolation system is a mechanical low-pass filter, and like any low-pass filter it has a corner. Below the corner the frame follows the floor; above it the floor motion is attenuated, and the attenuation improves as the frequency rises. So the corner frequency is the specification that decides what the system can do, and everything above 1.6 Hz in the vertical direction and above 1.2 Hz in the horizontal direction falls in the isolated region. Building vibration from traffic, from footsteps, from pumps and from the building itself is concentrated in the range from a few hertz upward, which is exactly the range this frame covers.

That is the reason a support frame like this is worth its cost in a sensitive experiment, and it is also the reason a cheap passive frame is not a substitute. A passive air system has the same idea but a higher corner, because the air volume that sets the stiffness is smaller and the leveling function is mechanical. A rigid frame bolted to the floor has no corner at all: it transmits from 0 Hz upward, and the only thing between the experiment and the building is the mass of the table.

Where the 1.6 Hz comes from matters for reliability as much as for performance. It is set by the physical compliance of the air chambers under the load, which is a property of geometry and pressure, not of a control algorithm. There is no gain to tune, no filter to re-optimise when the payload changes, and no controller state that behaves differently after a power cycle. The leveling is pneumatic as well: air pressure in the isolators does the work, and the system re-levels itself as the load changes, which is why a 700 kg capacity frame can accept a payload that is assembled in stages without being re-set up between stages.

The cost side of the bargain has to be stated as plainly as the benefit. An air-mounted frame needs a constant source of pressurised air. Not a reservoir that is filled once, but a continuous supply at regulated pressure for as long as the experiment runs. If the air supply is interrupted the table settles onto its stops, and any measurement in progress is lost. That single site requirement is the most common reason a frame like this cannot be installed in a room that was otherwise suitable, so it should be confirmed before the order rather than after delivery.

Key Features

  • Resonant frequency below 1.6 Hz vertical and below 1.2 Hz horizontal. The corner of the isolation band. Everything above those frequencies is attenuated, which covers the building and footfall vibration that matters in a laboratory.
  • Four independent, air mounted, active isolators. Each corner carries its own isolator, so a load that is not centred is handled by differential pressure rather than by a rigid frame fighting itself.
  • Pneumatic self-leveling with ±0.25 mm repeatability. The frame returns to the same height after a load change, without an operator adjusting anything.
  • 700 kg (1,545 lbs) load capacity. Enough for a large breadboard, a heavy optical assembly and the fixtures that hold it, with margin.
  • 700 mm (27.5 in) frame height. A working height that suits a standing or seated operator and leaves room underneath for the air system and the leveling hardware.
  • Matched to a 900 x 1500 mm (36 in x 60 in) breadboard. One of six frame sizes in the family, covering breadboards up to 1200 x 1800 mm (48 in x 72 in).
  • Sturdy all-steel construction. The frame is not the compliant element; the air springs are. Steel keeps the structure rigid between the isolators so the table top does not flex independently of the leveling system.
  • Leveling pads ±9.5 mm and leveling feet ±5 mm. Two layers of adjustment, so an uneven floor is corrected at the foot before the air system is asked to compensate.
  • Optional PWA061 caster set. Turns a fixed installation into something that can be moved between rooms, at the cost of having to re-level afterwards.
  • Serviceable isolators. Air springs are a wear item in the long run, and a four-corner architecture means one can be replaced without scrapping the frame.
  • Below 13 dB vertical and below 8 dB horizontal at resonance. The peak the table top sees as it crosses its own corner is bounded, which is what keeps a slow scan from being shaken at exactly the frequency the experiment is most sensitive to. A passive frame of the same footprint typically shows around 24 dB at this point.
  • -18 dB at 5 Hz and -34 dB at 10 Hz, both axes. That is 87.5 percent of the floor motion removed at 5 Hz and 98 percent at 10 Hz. The band above 10 Hz is where most building vibration sits, and it is attenuated by roughly a factor of fifty in amplitude.

Technical Specifications

Parameter Specification
Model PFA51502
Product type Active isolation breadboard support frame
Frame height 700 mm (27.5 in)
Breadboard size matched 900 x 1500 mm (36 in x 60 in)
Load capacity 700 kg (1,545 lbs)
Isolator configuration Four independent, air mounted, active vibration isolators
Leveling method Pneumatic self-leveling
Leveling repeatability ±0.25 mm (0.010 in)
Vertical resonant frequency below 1.6 Hz
Horizontal resonant frequency below 1.2 Hz
Vertical transmissibility at resonance below 13 dB
Horizontal transmissibility at resonance below 8 dB
Vertical transmissibility at 5 Hz -18 dB (87.5%)
Horizontal transmissibility at 5 Hz -18 dB (87.5%)
Vertical transmissibility at 10 Hz -34 dB (98%)
Horizontal transmissibility at 10 Hz -34 dB (98%)
Height adjustment, leveling pads ±9.5 mm (±0.375 in)
Height adjustment, leveling feet ±5 mm (±0.2 in)
Isolators height adjustment range ±6 mm (0.25 in)
Legs height adjustment range ±10 mm (0.4 in)
Total height adjustment range, breadboard over the full system 26 mm (1.02 in)
Construction Sturdy, all-steel
Finish Black Paint
Air supply Requires a constant source of pressurised air
Air pressure required 690 kPa (100 psi) maximum
Optional accessory PWA061 caster set
Breadboard range supported by the frame family Up to 1200 x 1800 mm (48 in x 72 in)

Two conventions in this table are easy to misread, so they are stated here. The percentages in brackets are the share of floor motion that the frame removes, not the share it passes: -34 dB leaves about 2.0 percent of the motion, which is 98 percent attenuated, and -18 dB leaves about 12.6 percent, which the datasheet rounds to 87.5 percent. The height figures come from two different parts of the frame. The Features list quotes leveling pads at ±9.5 mm and leveling feet at ±5 mm, which are the static adjusters under the legs; the rows above quote ±6 mm for the isolators and ±10 mm for the legs, which are the travel limits of the pneumatic elements and of the leg structure. They describe different components and are not alternatives to each other. For selection, use the rows above. The 26 mm entry is the breadboard height range of the complete system, that is, isolator travel and leg travel taken together. The corner frequencies are published by Thorlabs as limits, below 1.6 Hz and below 1.2 Hz, and are used elsewhere on this page as shorthand for those limits.

Read the height adjustment rows together with the leveling repeatability row, because they describe different things. The pads and feet are static adjustment: they set the frame level on an uneven floor, once, during installation. The 0.25 mm repeatability is dynamic behaviour: it is how closely the frame returns to the same height after the load changes. A frame that is perfectly leveled on installation and cannot repeat its height under a changing load will still drift out of alignment during a long scan.

Applications

Interferometry. A fringe pattern is a direct readout of optical path difference, which makes it a sensitive detector of floor motion. A frame with a 1.6 Hz vertical corner removes the building vibration that would otherwise appear as fringe jitter and as a slow drift in the phase map over a long acquisition.

Cell injection and micromanipulation. Injecting into a cell requires holding a pipette tip steady relative to a target a few micrometres across, for long enough to complete the procedure. Footfall in the corridor is the usual cause of a failed attempt, and a frame of this type removes it.

Non-contact surface measurement. Optical profilometry, confocal displacement sensing and white light interferometry all measure height against a reference that is assumed to be still. If the reference moves, the measurement records the motion of the frame rather than the topography of the sample. Low frequency isolation is what makes a sub-micrometre height measurement repeatable.

Microscopy and live imaging. Long time-lapse acquisitions accumulate drift. A frame with pneumatic self-leveling keeps the focal plane where it was set even as the stage load changes, which is the difference between a usable time series and one that has to be re-focused by hand.

Any motion-sensitive measurement in a building that cannot be modified. Where the room is above a workshop, next to a lift shaft or on a suspended floor, structural fixes are usually impossible. A support frame is the intervention that can be made inside the room.

Selection Guide

Four checks decide whether this frame is the right one. Do them in order, because the first two can rule the product out entirely.

  • Check 1, the air supply. Confirm that a continuous regulated air line can be brought to the frame position, that it can stay connected for the duration of the experiment, and that the pressure will not be switched off at night by a building service. Without that, an air-mounted frame is the wrong product regardless of its isolation performance.
  • Check 2, the load. Add the breadboard, the optical assembly, the fixtures and the cable load, then compare against 700 kg. Leave margin: a frame loaded to its limit has less reserve for a payload that grows, and the resonant frequency is a function of the load it carries.
  • Check 3, the breadboard footprint. This frame matches 900 x 1500 mm (36 in x 60 in). If the breadboard is a different size, choose the corresponding frame from the family rather than overhanging or underhanging the top.
  • Check 4, the floor and the access route. The leveling feet cover ±5 mm and the pads ±9.5 mm, which handles a floor that is out of level but not one that is structurally sloping. Also confirm the route into the room, since an all-steel frame of this size does not go through a standard door without planning.

One further point on the load figure. The 700 kg capacity is a structural limit, and the isolation performance at that load is not the same as at half that load, because the air springs are stiffer when more compressed. A frame specified for a 400 kg payload will have a slightly lower resonant frequency than one loaded to 700 kg, which is in the user interest; a frame specified at the limit has no reserve. Sizing to roughly 70 to 85 percent of capacity is the usual compromise between isolation performance and headroom.

Series Comparison

Model Breadboard size matched
PFA51509 750 x 750 mm
PFA51505 750 x 900 mm
PFA51508 750 x 1200 mm
PFA51507 900 x 1200 mm
PFA51502 (this page) 900 x 1500 mm
PFA51504 1200 x 1500 mm

All six are 700 mm (27.5 in) frame height active isolation frames built on the same four-isolator architecture, and the frame family covers breadboards up to 1200 x 1800 mm (48 in x 72 in). The choice between them is a footprint decision rather than a performance decision: a larger frame carries a larger breadboard and usually a larger load, but the isolation principle and the pneumatic leveling are shared. Confirm the load capacity of the specific size on its own datasheet, because capacity does not scale identically with footprint.

The practical consequence is that a laboratory planning several benches should choose sizes from this list to match the breadboards it already owns, rather than ordering breadboards to match a frame. Breadboards are the part that gets reused across projects; frames tend to stay in the room they were installed in.

FAQ

Q: Why is the resonant frequency more important than an isolation ratio?

A: Because the resonant frequency defines the whole curve. A support frame behaves as a mechanical low-pass filter with a corner at its resonant frequency: below the corner the payload follows the floor, above it the floor motion is attenuated and the attenuation keeps improving with frequency. A quoted ratio at one frequency tells you the value at that frequency only. The 1.6 Hz vertical and 1.2 Hz horizontal corners tell you that the entire band above roughly 2 Hz is in the isolated region, which is where building vibration lives.

Q: What does pneumatic self-leveling mean in practice?

A: It means the frame returns itself to level using air pressure in the isolators, with a repeatability of ±0.25 mm (0.010 in). When the payload changes, or when the frame is disturbed, the air system re-establishes the working height without an operator turning a screw. The leveling path is pneumatic, so there is no servo gain to tune and no controller state to re-establish after a shutdown.

Q: Can it be moved after installation?

A: Yes, with the optional PWA061 caster set. The frame is all steel and heavy, so moving it is a planned operation rather than a casual one, and the frame has to be re-leveled and allowed to settle afterwards. For a room that changes layout regularly, the casters are worth ordering with the frame rather than later.

Q: What happens if the air supply fails?

A: The table settles onto its mechanical stops. There is no damage to the optics in a normal installation, but any measurement in progress is lost and the frame has to be re-leveled once pressure returns. This is why the air supply check comes first in the selection sequence: a frame that loses pressure every evening is not delivering isolation for most of its life.

Q: Is 700 kg enough for a large breadboard plus a full optical assembly?

A: Usually, but the arithmetic has to include everything: the breadboard itself, the mounts, the laser or source, the detector, the enclosures and the cable load. A 900 x 1500 mm steel breadboard is already a substantial part of the budget. If the total lands within 15 percent of 700 kg, check the capacity of the next size up before committing.

Q: What floor condition does it need?

A: A floor that is flat but not necessarily perfectly level. The leveling feet cover ±5 mm and the leveling pads ±9.5 mm, which absorbs normal construction tolerance. A floor with a significant structural slope, or one that flexes under footfall, needs attention before the frame is installed, because the frame isolates the payload from floor motion but cannot remove a slope.

Q: Does it come with the breadboard?

A: No. The frame is the support structure; the breadboard is a separate item matched to the 900 x 1500 mm (36 in x 60 in) size. Ordering the frame and the top together is the usual approach, because the mounting interface between them is what determines the assembled height.

Usage Precautions

  • Never operate without a continuous air supply. The isolators are air mounted. Loss of pressure drops the table onto its stops, and a frame that is cycled on and off daily spends much of its life not isolating anything.
  • Level the feet before pressurising. Set the frame level mechanically on the floor using the feet and pads, then bring the air system up. Asking the air system to correct a structural slope uses up its adjustment range and leaves less reserve for load changes.
  • Distribute the load. The four isolators work best when the centre of mass is near the centre of the frame. A payload concentrated at one corner forces that isolator to carry a disproportionate share and reduces the effective capacity.
  • Do not slide heavy items across the breadboard. The frame is compliant by design. A sudden lateral load will move the top relative to the floor, and an optic that is being positioned at the time will move with it.
  • Re-check alignment after any pressure event. After a supply interruption, a move on casters, or a significant change of payload, allow the frame to settle and then verify the alignment rather than assuming the leveling has restored the previous state.
  • Keep the isolators accessible. Leave clearance around each corner so that pressure can be checked and an isolator replaced without dismantling the experiment.
  • Plan the installation route. An all-steel frame at this size is not a lift-and-carry item. Confirm door widths, lift capacity and floor loading before delivery day, and use the caster set or lifting equipment as appropriate.

Disclaimer

The values on this page are summarised from the manufacturer published specification for PFA51502 and are provided to support selection. The current official datasheet and drawing take precedence where they differ from this summary, and specifications may be revised without notice. Load capacity, resonant frequencies and leveling repeatability are quoted for the conditions stated by the manufacturer and will vary with the payload actually installed. No transmission curve is reproduced here; where a project requires a specific isolation performance at a specific frequency, request the current performance data for the exact configuration rather than extrapolating from a catalogue summary. No price is stated on this page.

One site condition deserves a final mention because it sits outside the specification table. The frame needs a regulated air line that stays pressurised for the duration of the experiment, and the pressure and flow required should be taken from the installation manual for the exact model rather than estimated from the load capacity. A room that can supply air during working hours but loses it overnight will give isolation during the day and a table resting on its stops every morning, which is a maintenance problem rather than a performance one, but it is worth designing out before the frame is delivered.

Contact Us

For help choosing between the six frame sizes, for confirmation of load capacity for a particular payload, or for a quotation including the PWA061 caster set, contact the sales team with the breadboard dimensions, the estimated total load including fixtures and cables, the resonant frequency target if the experiment has one, and confirmation that a continuous air supply is available at the installation position. Those four items are enough to specify the frame and to flag any site problem before an order is placed.

For a project where the frame and the breadboard are ordered together, send both requirements in one message so that the mounting interface and the assembled working height can be confirmed as a pair. For a frame going into an existing room, include the floor condition, the door width on the access route and whether casters are wanted; those three details decide whether the delivery is a straightforward installation or a rigging job.

Reviews

There are no reviews yet.

Be the first to review “Thorlabs PFA51502 Active Isolation Breadboard Support Frame, 700 mm Height, 900 x 1500 mm”

Your email address will not be published. Required fields are marked *

中文EN