QQ: 859818709

Aspheric Sag Calculator

Aspheric Sag Calculator

Aspheric Sag Calculator

Calculate the sag and best-fit radius of an aspheric surface, supporting the conic constant and higher-order even aspheric coefficients (A2–A12), for optical design and surface profiling

🔬 Sag
📐 Best-fit radius
🔧 Conic constant k
📊 Higher-order coefficients A2–A12
📈 Sag curve
Sag Optical axis Aspheric surface Sphere D r = D/2

🔬 Aspheric Sag Calculator

Enter the aspheric parameters to calculate the sag and best-fit radius at a specified aperture


mm


mm


—


mm⁻¹


mm⁻³


mm⁻⁵


mm⁻⁷


mm⁻⁹


mm⁻¹¹
💡 Aspheric equation: z(r) = cr²/[1+√(1−(1+k)c²r²)] + A₂r² + A₄r⁴ + A₆r⁶ + A₈r⁸ + A₁₀r¹⁰ + A₁₂r¹², where c = 1/R and r is the radial coordinate

Calculation results
Edge sag
—
mm
Best-fit radius
—
mm
Aspheric departure
—
mm
Spherical sag
—
mm
Curvature
—
mm⁻¹
Surface type
—
—

PARAMETER GUIDE

Parameter details

Understand the physical meaning of each parameter in the aspheric equation

Clear aperture

D

The effective clear diameter of the aspheric element. The semi-aperture y = D/2 is the radial position at which the sag is calculated.
Unit: mm
Engineering significance:Determines the actual region of the optical element through which the beam passes, directly affecting the system throughput and edge aberrations.

Radius of curvature

R

The radius of curvature at the vertex of the aspheric surface, determining the basic curvature of the surface. Curvature c = 1/R. Positive R denotes a convex surface and negative R a concave surface.
Unit: mm
Engineering significance:Determines the basic focusing/diverging power of the optical element and is the primary parameter in paraxial optical design.

Conic constant

k

Determines the conic section type of the surface: k=0 is a sphere; k>0 an oblate spheroid; k=-1 a paraboloid; k<-1 a hyperboloid.
Dimensionless
Surface classification:Sphere k=0 | Ellipsoid k>0 | Paraboloid k=-1 | Hyperboloid k<-1

Higher-order aspheric coefficients

A₂ ~ A₁₂

Higher-order polynomial correction terms superimposed on the conic surface, used to control the surface shape precisely and correct residual aberrations.
Unit: mm⁻¹ ~ mm⁻¹¹
Engineering significance:The closer the higher-order coefficients are to zero, the easier the surface is to manufacture; the larger their absolute values, the greater the manufacturing difficulty and inspection complexity.

Sag

Sag (z)

The axial depth (or height) of the aspheric surface relative to the tangent plane at the vertex at a given radial position; it is the core parameter for surface machining and inspection.
Unit: mm
Engineering significance:Sag is the key quantity controlled in grinding and polishing during optical fabrication, and also the reference for surface deviation in interferometric testing.

Best-fit radius

R_bf

The radius of the sphere that most closely matches the aspheric sag over a specified aperture. Calculated from R_bf = (y² + z²) / (2z).
Unit: mm
Engineering significance:Used to determine the reference sphere radius for testing (such as an interferometer reference), and is the most important reference parameter in optical testing.

FORMULAS

Core formulas

Key formulas involved in aspheric sag calculation

1
Aspheric sag equation
z(r) = cr² / [1+√(1−(1+k)c²r²)] + ΣA₂ₙr²ⁿ
The complete expression for aspheric sag: the first term is the conic base term and the second is the sum of even higher-order corrections (n = 1,2,…,6 corresponding to A₂–A₁₂).
2
Curvature definition
c = 1 / R
The curvature c is the reciprocal of the radius of curvature R. A positive value corresponds to a convex surface (facing the incident light) and a negative value to a concave surface.
3
Best-fit sphere radius
R_bf = (y² + z²) / (2z)
Here y = D/2 is the semi-aperture and z is the edge sag. This sphere matches the aspheric sag at the edge and serves as the reference surface for interferometric testing.
4
Aspheric departure
Δz = z_aspheric − z_sphere
The departure of the aspheric surface from the best-fit sphere, reflecting the amount of aspheric correction. The greater the departure, the higher the manufacturing and inspection difficulty.
5
Spherical sag
z_sph = R − √(R² − r²)
The sag of a standard sphere at radial position r, used for comparison with the aspheric sag to assess the amount of aspheric correction.
6
Conic section classification
k=0 → sphere | k>0 → ellipsoid | k=−1 → paraboloid | k<−1 → hyperboloid
The conic constant k determines the geometric type of the base surface. Different k values correspond to different conic section curves.

COMMON MISTAKES

Common misconceptions

Common mistakes in aspheric design and testing

A₂ is defined differently from the other higher-order coefficients

Different optical manufacturers define A₂ differently. Some incorporate A₂ into the radius of curvature (i.e. R already includes the effect of A₂), while others retain it explicitly. When using Thorlabs data, A₂ is usually zero or very small because the radius of curvature has absorbed this effect. Always confirm the definition when comparing data across manufacturers.

Ignoring the sign convention for the radius of curvature

Radius-of-curvature sign conventions may differ between optics textbooks and manufacturers. In the sag formula, the sign of R directly affects the sign of the sag (convex/concave). A consistent sign convention must be maintained when substituting into the formula, otherwise the result will be completely reversed.

Best-fit radius = vertex radius of curvature

The best-fit radius R_bf is not equal to the vertex radius of curvature R. R_bf accounts for the aspheric departure over the entire aperture and usually differs significantly from R. In aspheric testing, R_bf rather than R should be used as the interferometer reference surface.

Higher-order coefficients can be truncated arbitrarily

Higher-order aspheric coefficients are not mere precision corrections; each term contributes to the surface shape in a particular radial region. Arbitrarily neglecting higher-order terms (even when numerically small) can significantly increase surface deviation in the edge region and degrade image quality.

The greater the sag, the harder it is to manufacture

Sag itself is not the only determinant of manufacturing difficulty. More critical is the aspheric departure (Δz) and its spatial frequency distribution. An element with a large sag but close to spherical may be easier to manufacture than one with a small sag but large high-frequency departure.

No higher-order terms are needed for a paraboloid with k = −1

For imaging of objects at infinity, an ideal paraboloid indeed needs only k = −1. In practice, however, aspheric mirrors often require higher-order corrections to compensate for residual aberrations of other system components, so a parabolic mirror may also have non-zero higher-order coefficients.

PRACTICAL EXAMPLES

Application examples

Typical aspheric parameters and calculation scenarios

1

Sag calculation for a typical aspheric lens

Given conditions
D = 25 mm
R = 50 mm
k = −1 (paraboloid)
A₄ = 1×10⁻⁶ mm⁻³
All other higher-order terms = 0
  • Calculate curvature: c = 1/R = 1/50 = 0.02 mm⁻¹
  • Semi-aperture: r = D/2 = 12.5 mm
  • Conic base term: z_conic = cr²/[1+√(1−(1+k)c²r²)] = 0.02×156.25/[1+√(1−0)] = 3.125/(1+1) = 1.5625 mm (the denominator is exactly 2 when k=−1)
  • Higher-order correction: A₄r⁴ = 1×10⁻⁶ × 12.5⁴ = 0.0244 mm
  • Total sag: z = 1.5625 + 0.0244 =1.5869 mm
  • Best-fit radius: R_bf = (12.5² + 1.5869²)/(2×1.5869) =49.96 mm
  • 💡 Key point:For a paraboloid (k=−1), the denominator of the conic base term simplifies to 2, making the calculation straightforward. Although the coefficient of the higher-order term A₄ is small, after amplification by r⁴ it still contributes about 0.024 mm and cannot be neglected.
    2

    Analysis of the difference between aspheric and spherical surfaces

    Given conditions
    D = 50 mm
    R = 100 mm
    k = −0.5
    A₄ = 5×10⁻⁸ mm⁻³
  • Spherical sag: z_sph = R − √(R²−r²) = 100 − √(10000−625) = 100 − 96.825 = 3.175 mm
  • Aspheric conic base term: c=0.01, r=25, (1+k)=0.5 → z_conic = 0.01×625/[1+√(1−0.5×0.0001×625)] = 6.25/[1+√0.96875] = 6.25/1.9843 = 3.150 mm
  • Higher-order correction: A₄r⁴ = 5×10⁻⁸ × 390625 = 0.0195 mm
  • Total aspheric sag: z = 3.150 + 0.0195 = 3.170 mm
  • Departure: Δz = 3.170 − 3.175 =−0.005 mm
  • 💡 Key point:In this example the aspheric departure is only 5 μm, but it already far exceeds the interferometric testing accuracy requirement of λ/4@632.8 nm ≈ 0.158 μm. This shows that even a tiny aspheric departure can have a significant impact in precision optics.
    ⚠

    Common mistake: neglecting the effect of higher-order coefficients

    Scenario description
    An aspheric condenser lens
    D = 50 mm,R = 80 mm
    k = −1.2,A₆ = 2×10⁻¹¹
  • Incorrect approach:Calculate only the conic base term, ignoring all higher-order coefficients and assuming A₆ = 2×10⁻¹¹ is “small enough”
  • Actual calculation: A₆r⁶ = 2×10⁻¹¹ × 25⁶ = 2×10⁻¹¹ × 2.44×10⁸ = 0.0049 mm
  • This 4.9 μm deviation may exceed the system’s allowable wavefront error tolerance
  • Correct approach:Always include all non-zero higher-order coefficients, even if their values appear small
  • 💡 Key point:The “smallness” of higher-order coefficients is relative. When the radial distance r is large, the high power r²ⁿ amplifies a small coefficient into a non-negligible contribution. In systems with a large aperture, terms such as A₆ and A₈ can produce deviations of several micrometres.
    中文EN