📷 Pixel Size ↔ Resolution (lp/mm) Calculator
Pixel Size ↔ Resolution (lp/mm) Calculator
Convert bidirectionally between camera pixel size (pixel pitch) and spatial resolution (line pairs/mm, lp/mm), and evaluate whether the camera sensor resolution matches the optical system MTF cutoff frequency, quickly identifying the system bottleneck. Suitable for machine vision, laser inspection imaging and camera selection.
📷 Pixel Size ↔ Resolution Calculator
Three modes: calculate resolution from pixel size, derive the required pixel size from a target resolution, and evaluate sensor-to-optics MTF matching
μm
Centre-to-centre spacing of adjacent pixels; see ‘pixel size / pixel pitch’ in the camera datasheet
Effective resolution reduction factor, typically 0.7~0.9; the default 1.0 means no reduction
Formula details
From pixel pitch to Nyquist resolution, then to the optical diffraction MTF cutoff and the system matching criterion
Parameter details
Three key quantities: pixel size, Nyquist frequency and optical MTF cutoff frequency
Pixel size p
- Unit: μm; listed in datasheets as ‘pixel size / pixel pitch’
- Common industrial cameras: 1.4 ~ 7.4 μm
- Smaller p → more pixels per millimetre → fNhigher
- but small pixels collect less light, and the signal-to-noise ratio and dynamic range usually decrease
Nyquist frequency fN
- Unit: lp/mm (line pairs/mm)
- fN= 500/p, the theoretical upper limit of discrete sampling
- Note: pixels/mm (dots/mm) is twice the lp/mm value; do not confuse them
- Actual effective resolution ≈ fN × Kell(0.7~0.9)
Optical MTF cutoff frequency fc
- Unit: lp/mm, fc = 1/(λmm·F/#)
- The shorter the wavelength and the smaller the f-number, the higher the optical cutoff frequency
- At λ=0.55 μm and F/5.6, fc ≈ 324.7 lp/mm
- compared with fNcomparing them tells you which end is the system bottleneck
📋 Quick-reference table of common pixel sizes
Comparison of pixel size, pixels per millimetre, Nyquist resolution and minimum single-line width
| Pixel size p (μm) | Pixels per millimetre (pixels/mm) | Nyquist fN(lp/mm) | Minimum single-line width (μm) | Typical sensor reference |
|---|---|---|---|---|
| 1.4 | 714.3 | 357.1 | 1.4 | High-resolution small-pixel inspection camera |
| 2.0 | 500.0 | 250.0 | 2.0 | High-speed / high pixel-density camera |
| 2.4 | 416.7 | 208.3 | 2.4 | Common 1/1.8″~1″ industrial cameras |
| 3.45 | 289.9 | 144.9 | 3.45 | Classic pixels of the Sony IMX series |
| 4.8 | 208.3 | 104.2 | 4.8 | Large-format high-SNR camera |
| 5.0 | 200.0 | 100.0 | 5.0 | General-purpose machine vision camera |
| 5.5 | 181.8 | 90.9 | 5.5 | Low-light / high-speed camera |
| 7.4 | 135.1 | 67.6 | 7.4 | Large-pixel high-sensitivity camera |
⚠️ Common pitfalls and notes
Six most common pitfalls in pixel-size/resolution conversion
Mistaking pixels (dots/mm) for line pairs lp/mm
The two differ by a factor of exactly 2. Pixels per millimetre = 1000/p, while one line pair requires 2 pixels, so fN= 500/p. At p=5 μm this is 200 pixels/mm, but only 100 lp/mm.
Do smaller pixels always give better imaging?
Not necessarily. As pixels get smaller, fNgets higher, but the actual system resolution is also constrained by the optical MTF cutoff frequency; if the lens resolution is insufficient, even the smallest pixels only produce ‘oversampling blur’, and small pixels also have poorer signal-to-noise ratio.
Ignoring the effect of wavelength and f-number on the optical cutoff
fc= 1/(λ·F/#). The longer the wavelength and the smaller the aperture (larger f-number), the lower the optical cutoff frequency. The optical resolution of blue light at F/2.8 and infrared at F/8 can differ by several times.
Confusing ‘line’ with ‘line pair’
In the TV-lines/TVL context, a ‘line’ sometimes means a single line, whereas lp/mm explicitly means a bright–dark pair of lines. The minimum single-line width ≈ p and the line-pair period = 2p; when quoting specifications, always check the unit definition.
Looking only at the total pixel count, not the individual pixel size
At the same 12 megapixels, the pixel size of a 1/1.7″ small format and a 1.1″ large format differs greatly, directly determining the resolution per millimetre and low-light performance. Spatial resolution depends on p, not on the total pixel count.
Treating the Nyquist limit as the actually achievable resolution
fNis the theoretical upper limit for ideal sampling; the actual effective resolution is about fN×Kell (0.7~0.9), with further degradation from lens MTF, alignment and motion blur; a margin should be left when selecting.


