QQ: 859818709

RayTools BM111E EtherCAT Smart Flat Sheet Laser Cutting Head, Process Monitoring (Discontinued)

RayTools BM111E EtherCAT Smart Flat Sheet Laser Cutting Head, Process Monitoring (Discontinued)

Price on request
Category:

Description

Product Overview

The BM111E was the EtherCAT version of the BM111 flat-sheet cutting head, and the fieldbus is the whole point of the model: focus and process monitoring travelled as bus traffic rather than as discrete signals. This model is discontinued and no longer in production; the page is retained for reference and spare-part identification.

Putting a cutting head on EtherCAT changes what can be supervised. Instead of a head that reports a fault after the fact, the control sees the process while it runs, which is why the E variant existed alongside the analogue BM111 rather than replacing it outright. The head remained a flat-sheet design; three-dimensional tube work was never its application. RayTools has replaced the model with the BS04K CAT-2D, the new-generation CAT series smart cutting head, described by the manufacturer as carrying a more complete set of smart sensing and monitoring functions. Only documented parameters appear below.

Key Features

  • EtherCAT fieldbus: focus commands and monitoring data travel on the bus, so the head is integrated into the machine’s control architecture rather than wired as a peripheral
  • Process monitoring: the head reports on the cut while it runs, which is the capability that separated the E variant from the analogue BM111
  • Flat-sheet application: a two-dimensional head for sheet cutting, not a 3D contour or tube head
  • Discontinued status: production has ended; the page is kept for identification, integration reference and spares
  • Replacement path: RayTools names the BS04K CAT-2D as the successor, with a wider sensing and monitoring set

Technical Specifications

Parameter Specification
Status Discontinued
Recommended replacement BS04K CAT-2D

Technical Notes

The documentation available for this discontinued model records its status and its replacement only. It publishes no rated power, focal length, clear aperture, weight, assist-gas pressure, EtherCAT cycle time or object-dictionary detail. No values have been carried across from the BM111 or from the BS04K CAT-2D, because bus behaviour and sensing scope differ between generations. For integration documentation on an installed machine, send the machine serial number and we will request it from the factory.

Series Comparison

Discontinued model Original use Recommended replacement
BM111E (discontinued) EtherCAT flat sheet cutting BS04K CAT-2D
BM114E (discontinued) EtherCAT flat sheet cutting BS08K CAT-2D

Selection Guide

  • This is the EtherCAT model. If the machine’s control already runs EtherCAT, the documented successor is the BS04K CAT-2D, which RayTools describes as carrying a more complete smart sensing and monitoring set.
  • If the machine uses discrete or analogue focus signalling, a bus head is the wrong replacement; the appropriate successor in the family is the analogue route, not this one.
  • For a higher power EtherCAT machine, the documented successor for the BM114E is the BS08K CAT-2D, which is a different model from the BS04K CAT-2D and should not be quoted interchangeably.
  • Before ordering, confirm the EtherCAT master, the device description file in use and the head mounting interface with us. A successor head must be integrated, not merely bolted on.
  • Do not read this page as an offer. It is a reference record of a head that is out of production, kept so that an installed machine can be identified, integrated and kept running on spares.

Usage Precautions

  • Never look into the beam or its specular reflection while the laser is running. Mark the work zone, fit guarding and screening, and wear eyewear rated for the wavelength in use.
  • EtherCAT cabling is part of the machine’s safety-relevant control path. Use screened cable, keep it separated from power runs and do not modify connector pinouts.
  • If the bus drops, stop the process and read the diagnostic before restarting. Repeated bus faults on an ageing head usually point at a connector or a cable, not at the control.
  • Check the protective window for spatter burns at each shift change; on a bus head a burnt window first appears as monitoring alarms, not as a bad cut.
  • Maintenance must be performed by a qualified technician with lockout and tagout applied, and the equipment must remain reliably earthed.
  • For the device description file, integration documents or spares on an installed BM111E, contact Changsha Soar Laser on +86 159 2722 0467 and quote the machine serial number as well as the head model.

Disclaimer

Specifications on this page are compiled from the manufacturer’s published material and the documentation available to us, and are provided as a selection reference only. The delivered product, the factory inspection report and the manufacturer’s latest specification sheet take precedence; appearance and configuration may change between batches, so please confirm with us before ordering. Reproduction of this page without written permission is not permitted.

Contact Us

Changsha Soar Laser Equipment Co., Ltd.  |  Hotline +86 159 2722 0467  |  www.soar-laser.cn  |  859818709@qq.com

Reviews

There are no reviews yet.

Be the first to review “RayTools BM111E EtherCAT Smart Flat Sheet Laser Cutting Head, Process Monitoring (Discontinued)”

Your email address will not be published. Required fields are marked *

中文EN