QQ: 859818709

Thorlabs PF0511 Ø1/2″ Zerodur Mirror Blank, Uncoated, 12.7 mm x 6.0 mm

Thorlabs PF0511 Ø1/2″ Zerodur Mirror Blank, Uncoated, 12.7 mm x 6.0 mm

Price on request
Category:

Description

Product Overview

The PF0511 is a Ø12.7 mm (Ø1/2 inch) mirror blank in Zerodur, 6.0 mm thick, with a polished front face and a fine ground back. The front surface is figured to λ/10 at 632.8 nm, polished to 10-5 scratch-dig, and held parallel to the back within 3 arcmin. Clear aperture is 90% of the diameter, diameter tolerance is +0.0 / -0.1 mm, thickness tolerance is ±0.2 mm, and the item number is engraved on the back.

It is a blank, and that word carries the whole commercial meaning of the part. There is no coating on it, so there is no reflectance specification and none should be inferred. An uncoated Zerodur face is not a mirror: it returns only the Fresnel reflection that any bare dielectric surface returns and lets the rest through. What has been bought here is a substrate that is already figured, already polished and already inspected to a standard tight enough to receive a coating, so that the coating house does not have to start from a ground disc.

The reason to specify Zerodur rather than fused silica is thermal expansion, and the difference is not marginal. Zerodur has a coefficient of thermal expansion of 0 plus or minus 0.100 x 10 to the minus 6 per degree Celsius. Fused silica is 0.55 x 10 to the minus 6 per degree Celsius. That is a factor of five and a half, and on a 12.7 mm part it is visible arithmetic: over a 20 K swing the Zerodur dimension moves about 25 nm while the fused silica dimension moves about 140 nm, a difference of 114 nm, which is roughly 0.18 of a wave at 633 nm. Those are linear dimensional changes, not wavefront error, and a mirror in a well-designed mount does not turn one directly into the other. What they describe is why a Zerodur substrate is the starting point when a system must hold alignment through a thermal cycle instead of being realigned after it.

Zerodur is a glass-ceramic, not a glass. A crystalline phase is grown in the material whose expansion is negative over the working range, and it cancels most of the positive expansion of the residual glass, which is how a coefficient near zero is achieved at room temperature rather than by a special alloy. Thorlabs sources substrate grade material for these blanks and names CO2 lasers, amplified Ti:sapphire lasers and industrial machining lasers as the intended applications, along with any other system sensitive to thermally induced beam drift.

The 10-5 polish deserves a note because it is tighter than the 40-20 specified on the finished mirrors in the same family. That is deliberate. A scratch or a dig in the substrate is replicated into the coating as a nucleation site and a scattering centre, so the blank is polished to a standard the coated part does not need to carry in its own specification. Coated parts are quoted at 40-20 because the coating process and the subsequent handling dominate the surface condition by then. Buying a blank at 10-5 and coating it does not give a 10-5 coated mirror; it gives a coating with fewer substrate-borne defects.

The back face is fine ground rather than polished, so it is a handling and mounting surface, not an optical one. It carries the engraved item number, which is the only identification once the part is in a mount, and it should never be lapped or marked by the customer.

Key Features

  • Uncoated mirror blank: a figured and polished substrate ready for coating, with no reflectance specification and none implied
  • Zerodur glass-ceramic substrate with a coefficient of thermal expansion of 0 plus or minus 0.100 x 10 to the minus 6 per degree Celsius, against 0.55 for fused silica
  • Roughly five and a half times more dimensionally stable than the fused silica equivalent through a thermal cycle
  • 10-5 scratch-dig front polish, tighter than the 40-20 of the coated mirrors, so substrate defects are not replicated into the film
  • λ/10 peak to valley at 632.8 nm with parallelism inside 3 arcmin, on a 12.7 mm diameter by 6.0 mm thick disc
  • Clear aperture 90% of the diameter and tolerances of +0.0 / -0.1 mm and ±0.2 mm, so standard half-inch mounts fit without rework
  • Fine ground back face carrying the laser-engraved item number, intended for handling and mounting only
  • Coating ready: accepts broadband dielectric, metallic or custom films, applied by the customer or arranged through us

Technical Specifications

Parameter Value
Model PF0511
Part type Mirror blank, uncoated
Coating None; supplied bare for customer or third-party coating
Material Zerodur glass-ceramic, substrate grade (registered trademark of Schott)
Coefficient of thermal expansion 0 ± 0.100 x 10^-6 per degree Celsius
Comparison, fused silica 0.55 x 10^-6 per degree Celsius
Diameter 12.7 mm (Ø1/2 inch)
Diameter tolerance +0.0 mm / -0.1 mm
Thickness 6.0 mm (0.24 inch)
Thickness tolerance ±0.2 mm
Front surface flatness λ/10 at 632.8 nm
Front surface quality 10-5 scratch-dig
Back surface Fine ground, item number laser engraved
Parallelism 3 arcmin or less
Clear aperture 90% of the diameter
Available coatings Broadband dielectric, metallic, or custom; applied after purchase
Source Thorlabs official series specification table

Applications

A blank is bought by two kinds of customer: the one who has a coater and the one who has a thermal problem. The applications below are where the second kind usually starts.

  • CO2 laser resonator and delivery optics: high average power heats the substrate and the mount, and a low expansion material holds the resonator axis through a warm-up cycle
  • Amplified Ti:sapphire beamlines: thermal lensing in the crystal is already handled, and the fold train should not add drift of its own between alignment sessions
  • Industrial machining laser heads: a head that runs a shift at a time cannot be realigned every few hours, so the fold substrates are chosen for dimensional stability
  • Interferometer end mirrors in thermal chambers: a reference surface that moves with temperature invalidates the measurement it is supposed to provide
  • Transportable and field instruments: hardware that crosses a temperature range on the way to site needs optics that do not need a reference flat on arrival
  • OEM builds with a customer-specified coating: the blank is bought to a figure and a polish, and the coating design is the customer intellectual property

Selection Guide

Two blanks share the same 12.7 mm by 6.0 mm envelope. The choice between them is a thermal requirement against a budget, and it is worth being honest about which one applies.

Choose When the requirement is What it costs
PF0511 Zerodur blank (this part) Alignment must survive a thermal cycle, or the laser power is high enough that substrate heating is real Higher substrate cost and a longer supply route than fused silica
Fused silica blank The bench is athermal, the power is modest, or the mount already dominates the drift Lower cost and wider availability, but five and a half times the expansion

The fused silica equivalent is the Ø12.7 mm fused silica mirror blank, and the comparison is deliberately easy: identical diameter, identical 6.0 mm thickness, identical λ/10 figure and identical mount interface. The differences are the material expansion coefficient and the surface quality, since the Zerodur blank is polished to 10-5 while the fused silica blank carries its own polish specification. If a system is already being realigned once a week for reasons unrelated to thermal drift, the Zerodur blank will not fix it and the fused silica part is the sensible buy.

There is a third route worth mentioning because customers ask for it: buy a finished Zerodur mirror instead of a blank. Thorlabs coats the same substrate with UV enhanced aluminum, protected aluminum, protected silver, protected gold and unprotected gold. If the wavelength is standard and the coating can be a catalogue one, a finished part is cheaper and faster than a blank plus a coating run. The blank is for the case where the coating is not standard.

Series Comparison

The Zerodur blank family is three sizes, and the thickness step is not proportional to the diameter step, which decides whether an existing mount can take a larger blank.

Item number Diameter Thickness Front polish Figure and parallelism
PF0511 12.7 mm +0.0 / -0.1 mm 6.0 mm ±0.2 mm 10-5 scratch-dig λ/10 at 632.8 nm, 3 arcmin or less
PF1011 25.4 mm +0.0 / -0.1 mm 6.0 mm ±0.2 mm 10-5 scratch-dig λ/10 at 632.8 nm, 3 arcmin or less
PF2011 50.8 mm +0.0 / -0.1 mm 12.0 mm ±0.2 mm 10-5 scratch-dig λ/10 at 632.8 nm, 3 arcmin or less

All three carry the same figure, the same polish and the same clear aperture fraction, so an aperture upgrade does not change the optical quality argument. The one-inch blank keeps the 6.0 mm thickness, which makes it a drop-in for a half-inch mount that has room to grow. The two-inch blank doubles to 12.0 mm, so the mount has to change with it.

FAQ

Is this a finished mirror? No. It is a blank. There is no coating on the front face, so there is no reflectance specification, and it will not perform as a mirror until one is applied.

What coating should I put on it? That depends on the band and the power. A broadband dielectric stack gives the highest reflectance over a limited range, a protected metal gives broadband coverage at a lower figure, and an unprotected metal gives the highest infrared figure at the cost of all handling tolerance. Tell us the wavelength, the bandwidth and the power density and we will narrow it down.

Can you arrange the coating? We can. The blank is bought to a figure and a polish and the coating is a separate step. Send the requirement with the order and we will quote the coated part rather than leaving you to find a coating house.

Why is the polish 10-5 when the coated mirrors are 40-20? Because the substrate is what the coating is deposited onto. A dig in the substrate becomes a defect in the film, so the blank is held tighter than the finished part needs to be. It does not mean the coated result will be 10-5.

How much better is Zerodur than fused silica really? The expansion coefficient is 0 plus or minus 0.100 against 0.55, a factor of five and a half. On this 12.7 mm part, a 20 K swing moves the dimension by about 25 nm instead of about 140 nm. Whether that matters depends entirely on how much of your drift is thermal and how much is the mount.

Can I hold it with a retaining ring? Yes, unlike the bare metal mirrors, the blank has no soft film to abrade. Seat it with light pressure anyway, because a ring tightened by feel will distort a 6.0 mm disc and the figure is the thing you paid for.

Does the back face need polishing? No. It is fine ground by design, it is not an optical surface, and it carries the engraved item number. Do not lap it or mark it.

Usage Precautions

  • Treat the polished front face as the optical surface from the moment the part is unpacked; a blank that is scratched before coating cannot be recovered by the coater
  • Handle by the edge with gloves, and never place the part face down on a bench or on its own packaging
  • Keep the front face covered when the part is out of its container, since dust that settles before coating becomes a coating defect
  • Do not clean with hydrofluoric acid or fluoride-bearing etchants; Zerodur is a glass-ceramic and is attacked by them
  • Avoid thermal shock, and bring the part to the bench temperature before coating or mounting it
  • Do not mark, lap or machine the fine ground back face; the engraved item number is the only identification once the part is mounted
  • Store flat, dry and away from abrasive dust, and do not stack blanks face to face without an interleaf

Disclaimer

Specifications are transcribed from the Thorlabs Zerodur mirror blank specification table for selection purposes. The official datasheet in force at the time of purchase governs, and the manufacturer may revise figures or processes without notice. This part is supplied uncoated and carries no reflectance specification; any optical performance figure depends on the coating applied afterwards and is the responsibility of the coating supplier. The thermal expansion figures describe linear dimensional change of the substrate material and are not a wavefront or beam drift specification for a mounted assembly. Coating service, price and lead time are quoted by our sales team.

Contact Us

Changsha Soar Laser Equipment Co., Ltd. supplies genuine Thorlabs optics to laboratories and machine builders in China. Blanks are the part of the catalogue where a short conversation saves the most money, because the coating decision is still open. Send the wavelength, the bandwidth, the power density and a sentence about why the drift matters, and we will come back with a coating recommendation and a coated price rather than a bare part number. Hotline +86 159 2722 0467, email 859818709@qq.com, website www.soar-laser.cn.

Reviews

There are no reviews yet.

Be the first to review “Thorlabs PF0511 Ø1/2″ Zerodur Mirror Blank, Uncoated, 12.7 mm x 6.0 mm”

Your email address will not be published. Required fields are marked *

中文EN