Description
Product Overview
The Thorlabs PF05-03 is not a finished mirror. It is the substrate a mirror is made from: a Ø12.7 mm (Ø1/2 inch) disc of substrate-grade fused silica, 6.0 mm thick, with the front face polished to better than λ/10 flatness and 10-5 scratch-dig and the back left fine ground. No film is deposited on it, so the page carries no reflectance figure, no operating wavelength range and no laser damage threshold. Those properties belong to whatever coating the user puts on the blank.
The part exists because coatings are often the variable in a design rather than the constant. A coating house that wants to deposit its own stack needs a known substrate to deposit it on; an OEM that builds the coating step into its own process needs a repeatable substrate in volume; a laboratory that is developing a custom film needs to iterate on a standard polish instead of a custom optic. In each case the requirement is the same: a flat, clean, dimensionally stable disc whose optical properties are entirely determined downstream. That is what the blank supplies, and the fused silica is chosen for it because the material transmits from 185 nm to 2.1 µm, is homogeneous, and holds its figure through thermal cycling better than most glasses.
The numbers on the blank are surface numbers, not optical numbers. Front surface flatness is better than λ/10, front surface quality is 10-5 scratch-dig, clear aperture is 90% of the diameter, diameter tolerance is +0.0 / -0.1 mm and thickness is 6.0 mm ± 0.2 mm with a fine-ground back. The polish is specified tighter than on the coated mirrors sold on the same substrate, which are quoted at 40-20: the figure for a blank describes the surface before deposition, and the process that follows decides what the coated part finally achieves. A λ/20 front surface is available as a custom order through Thorlabs technical support, and the blank is offered in four diameters – Ø1/2 inch, Ø19 mm, Ø1 inch and Ø2 inch – and in quantity.
Buyers should be clear about one thing before ordering: if the requirement is a mirror that reflects light on arrival, this is the wrong page. The same 12.7 mm substrate is sold coated as the PF05-03-F01 for 250 to 450 nm, the PF05-03-G01 for 450 nm to 20 µm, the PF05-03-P01 for higher visible and near-infrared reflectance, and the PF05-03-M01 for 800 nm to 20 µm. The blank is for the case where none of those coatings is the one that is needed.
Key Features
- Uncoated by design: no film, therefore no reflectance, wavelength range or damage threshold is specified – the user deposits the coating
- Substrate-grade fused silica: transmits from 185 nm to 2.1 µm and is chosen for homogeneity and environmental durability rather than for a coating
- Front face figured to better than λ/10 at 10-5 scratch-dig, with a fine-ground back surface so the disc is not mistaken for a window
- Ø12.7 mm x 6.0 mm ± 0.2 mm: the same diameter and thickness as the coated half-inch mirrors, so it is a drop-in substitute in an existing mount
- Four diameters: Ø1/2 inch, Ø19 mm, Ø1 inch and Ø2 inch, and offered in quantity
- λ/20 option: a tighter front surface flatness can be ordered as a custom item through technical support
Technical Specifications
| Parameter | Value |
|---|---|
| Model | PF05-03 |
| Type | Uncoated mirror blank, front surface mirror substrate |
| Material | Substrate-grade fused silica |
| Substrate transmission range | 185 nm – 2.1 µm (material property, not a coated band) |
| Diameter | 12.7 mm (Ø1/2 inch) |
| Diameter tolerance | +0.0 mm / -0.1 mm |
| Thickness | 6.0 mm ± 0.2 mm |
| Front surface flatness | Better than λ/10 |
| Front surface quality | 10-5 scratch-dig |
| Back surface | Fine ground |
| Clear aperture | 90% of the diameter |
| Coating | None |
| Reflectance | Not specified, the part is uncoated |
| Custom option | λ/20 front surface flatness, by request through technical support |
| Source | Thorlabs official product page |
Applications
- In-house deposition: the blank is sent to an internal or contracted coating chamber for a proprietary stack that no catalogue part provides
- Custom coating development: a design can be iterated on a standard, well-characterised polish, so that a reflectance change is attributed to the film and not to the substrate
- OEM builds where coating is a process step: instruments that coat their own optics in volume need a repeatable disc, not a finished catalogue mirror
- Matched-thickness dummy in an alignment fixture: a 6.0 mm blank sitting in a mount reproduces the mechanical stack-up and the optical path offset of the coated mirror that will replace it, which lets an assembly be aligned before the coated parts arrive
- Shelf stock for a coater turnaround: holding blanks means a damaged coating can be replaced by a recoat rather than by a new catalogue order
Selection Guide
The first question is whether a coating already exists for the band. If it does, buy the coated part; if it does not, buy this blank and specify the film yourself. The table lists the coated mirrors that share this 12.7 mm substrate.
| Option | Band | Average reflectance | Part |
|---|---|---|---|
| Uncoated blank | Not applicable | None specified | PF05-03 (this page) |
| UV-enhanced aluminum | 250 nm – 450 nm | Above 90% | PF05-03-F01 |
| Protected aluminum | 450 nm – 2 µm / 2 – 20 µm | Above 90% / above 95% | PF05-03-G01 |
| Protected silver | 450 nm – 2 µm / 2 – 20 µm | Above 97% / above 95% | PF05-03-P01 |
| Protected gold | 800 nm – 20 µm | Above 96% | PF05-03-M01 |
If the requirement is a mirror that works on arrival, leave this page: the -F01 covers the ultraviolet, the -G01 covers 450 nm to 20 µm as the broadband workhorse, the -P01 gives the highest visible and near-infrared reflectance and the -M01 is the infrared workhorse. This page is for the case where the coating is the unknown, or where the coating is done in-house. Note also that the blank is not a transmission window: the front face is polished but the back is fine ground, so light passing through is scattered.
FAQ
Can I use the PF05-03 straight out of the box as a mirror? No. There is no reflective coating on it, so the polished fused silica face reflects only the few percent a bare glass surface returns. It becomes a mirror after a film is deposited, and the reflectance is then whatever that film provides.
Why is there no reflectance or damage threshold in the table? Because both are properties of the coating, and this part has none. Publishing a reflectance for an uncoated substrate would be meaningless, and a damage threshold quoted without a film would mislead. Once the blank is coated, the specification to use is the one for that coating.
Can Thorlabs coat the blank for me? Custom coating is part of the service: Thorlabs produces custom metallic and dielectric coatings on its own substrates and accepts both OEM volumes and single custom orders, and a λ/20 front surface flatness can be quoted as a custom item. Ask technical support with the band, the incidence angle and the required reflectance before ordering.
The blank is 10-5 but the coated mirrors are 40-20. Which number applies to my part? Both describe the same physical face at different stages. The 10-5 figure is the polish of the substrate as shipped; the 40-20 figure on the coated catalogue mirrors is the specification of the finished coated optic. Deposition adds scatter and inspection criteria change, so a blank should not be expected to remain at 10-5 after coating.
Will it fit where a coated half-inch mirror fits? Yes. The diameter is 12.7 mm with a +0.0 / -0.1 mm tolerance and the thickness is 6.0 mm ± 0.2 mm, which is the same envelope as the PF05-03-F01, -G01, -P01 and -M01. That dimensional match is the point of the part: it substitutes into an existing mount without a mechanical change.
Disclaimer
Specifications on this page are compiled from Thorlabs official published material and are provided as a selection reference only. The current official specification sheet governs; specifications and appearance may change without notice. Commercial terms and lead time are quoted by our sales team on request. Reproduction of this page without written permission is not permitted.
Contact Us
Changsha Soar Laser Equipment Co., Ltd. supplies genuine Thorlabs optics to laboratories and machine builders. For coating selection, aperture sizing, mount matching or lead time on a specific part number, contact us: hotline +86 159 2722 0467, email 859818709@qq.com, or use the enquiry form on www.soar-laser.cn. Tell us the wavelength, the beam diameter at the mirror and the pulse energy or continuous power, and we will confirm whether this coating is the right one before you order.









Reviews
There are no reviews yet.