Description
Product Overview
The Thorlabs PF05-03-G01 is the mirror most optical tables end up using: a Ø12.7 mm (Ø1/2 inch) protected aluminum plano mirror on a 6.0 mm fused silica substrate, specified from 450 nm to 20 µm. Average reflectance is above 90% from 450 nm to 2 µm and above 95% from 2 to 20 µm, so one part serves a HeNe alignment beam, a 1064 nm laser and a 10.6 µm thermal source without a coating change.
Aluminum is the default metal for a reason: its reflectance curve is the broadest of the simple films, and the protected version reproduces the reflectance of bare aluminum closely while adding a durable SiO2 overcoat that keeps the soft metal underneath from being touched. That overcoat is also what makes the part practical in a working laboratory, where an optic gets handled, mounted, dusted and occasionally wiped. Compared with protected silver, aluminum gives away reflectance in the visible and near-infrared, but it is markedly less sensitive to humidity: silver tarnishes when the overcoat is compromised, aluminum does not, and in a humid or poorly controlled room that difference decides the part.
The optical specification is the standard half-inch metal mirror specification: λ/10 peak-to-valley figure at 633 nm, 40-20 scratch-dig, parallelism within 3 arcmin, clear aperture 90% of the diameter, diameter tolerance +0.0 / -0.1 mm and thickness 6.0 mm ± 0.2 mm. That thickness matters more than it looks, because 6.0 mm is what the half-inch mounts and the lens-tube retainers are dimensioned around, so the mirror seats without a spacer and without being pinched at the rim.
For power handling the coating is rated at 0.3 J/cm² with 10 ns pulses at 1064 nm, and at 100 W/cm at 1.070 µm and 350 W/cm at 10.6 µm continuous. Those are modest figures next to a dielectric laser mirror, and they are the honest limit of a metal film: the failure mode is thermal, driven by absorption in the aluminum and in the overcoat, so the rating is given as linear power density along the illuminated line. Where the beam is tighter, more energetic or shorter in wavelength than 450 nm, the answer is a different coating rather than a larger aluminum mirror.
Key Features
- One part from 450 nm to 20 µm: above 90% average reflectance across the visible and near-infrared, above 95% from 2 to 20 µm, with no band gap to design around
- Protected aluminum: an SiO2 overcoat over the aluminum film, so the reflectance stays close to bare aluminum while the surface is protected for laboratory and industrial use
- More humidity tolerant than silver: the practical reason to specify aluminum in a room without tight environmental control
- Standard half-inch geometry: Ø12.7 mm, 6.0 mm thick, λ/10 at 633 nm, 40-20 scratch-dig, parallelism within 3 arcmin, clear aperture 90%
- Published thresholds: 0.3 J/cm² at 1064 nm with 10 ns pulses, 100 W/cm at 1.070 µm and 350 W/cm at 10.6 µm continuous
- Available in quantity: the same optic is sold as a 10-piece pack, PF05-03-G01-10, for builds that need more than one
Technical Specifications
| Parameter | Value |
|---|---|
| Model | PF05-03-G01 |
| Coating | Protected aluminum with SiO2 overcoat |
| Wavelength range | 450 nm – 20 µm |
| Average reflectance | Above 90% from 450 nm to 2 µm; above 95% from 2 to 20 µm |
| Substrate | Fused silica |
| Diameter | 12.7 mm (Ø1/2 inch) |
| Diameter tolerance | +0.0 mm / -0.1 mm |
| Thickness | 6.0 mm (0.24 inch) |
| Thickness tolerance | ±0.2 mm |
| Surface flatness | λ/10 peak to valley at 633 nm |
| Surface quality | 40-20 scratch-dig |
| Clear aperture | 90% of the diameter |
| Pulsed damage threshold | 0.3 J/cm² (1064 nm, 10 ns, 10 Hz, Ø1.000 mm) |
| CW damage threshold | 100 W/cm (1.070 µm, Ø0.098 mm); 350 W/cm (10.6 µm, Ø0.339 mm) |
| Source | Thorlabs official product page |
Applications
- General beam folding on an optical table: alignment beams, probe beams and pump beams are turned with a part that is kept in stock and covers the whole visible and infrared range
- Nd:YAG delivery at 1064 nm: below the published 0.3 J/cm² nanosecond rating, the mirror handles the beam path from laser to workpiece in a marking or trimming head
- CO2 laser alignment at 10.6 µm: above 95% average reflectance in the thermal infrared with a 350 W/cm continuous rating makes it a serviceable alignment optic, with a dielectric or gold mirror reserved for the focusing position
- FTIR and thermal imaging benches: the 2 to 20 µm band is covered without a separate infrared coating, which simplifies a multi-source instrument
- Teaching and prototype laboratories: the standard way to build a periscope, a delay arm or a multi-pass cell that has to work at several wavelengths
Selection Guide
Start from the shortest wavelength in the path, then check the power. The table lists the half-inch metal coatings; all of them share the same 12.7 mm substrate, so a change of coating is not a change of mount.
| Coating | Band | Average reflectance | Part number | Decision rule |
|---|---|---|---|---|
| UV-enhanced aluminum | 250 nm – 450 nm | Above 90% | PF05-03-F01 | The beam goes below 450 nm |
| Protected aluminum | 450 nm – 2 µm / 2 – 20 µm | Above 90% / above 95% | PF05-03-G01 (this page) | Broadband, humid room, general purpose |
| Protected silver | 450 nm – 2 µm / 2 – 20 µm | Above 97% / above 95% | PF05-03-P01 | Every photon in the visible counts, humidity is controlled |
| Protected gold | 800 nm – 20 µm | Above 96% | PF05-03-M01 | Infrared only, long service life wanted |
| Uncoated blank | Not applicable | None specified | PF05-03 | You will deposit your own film |
For quantity, this part is the single unit and PF05-03-G01-10 is the 10-piece pack of exactly the same optic. Buy the single unit to evaluate the coating on one arm of a setup; buy the pack when the design has already been proved and several mirrors are needed at once. Neither version differs optically, so a prototype built with singles and a production build from packs are the same optical system.
FAQ
Protected aluminum or protected silver for a general-purpose fold? Aluminum unless every percent of visible or near-infrared reflectance is needed. Silver returns more light between 450 and 800 nm, but it tarnishes if the overcoat is compromised and it demands controlled humidity. Aluminum gives up a few percent of reflectance and tolerates a normal laboratory environment, which is why it is the default folding mirror.
Is this the same optic as the 10-piece pack? Yes. The PF05-03-G01-10 pack contains ten mirrors of this part number with the same coating specification and the same mechanical dimensions. The pack is a purchasing unit, not a different product.
What is the difference between protected aluminum and bare aluminum? The overcoat. A bare aluminum film is soft, oxidises in air and cannot be touched without damage; the SiO2 layer seals it and makes the part usable as a laboratory and industrial optic. The reflectance curve stays close to that of bare aluminum, which is why protected aluminum is described as the closest match to an uncoated aluminium surface.
How much power will it take at 1064 nm? 0.3 J/cm² with 10 ns pulses at 10 Hz over a Ø1.000 mm spot, and 100 W/cm continuous at 1.070 µm. Calculate the energy density or the linear power density at the mirror surface for your own beam, including any focusing, and keep a margin: contamination on the surface reduces the threshold well below the published figure.
Why is there no parallelism figure in some catalogues for this part? Because it is not a free parameter for a plano mirror of this thickness; the figure that is specified and that matters for beam steering is the λ/10 surface flatness at 633 nm, together with the 40-20 scratch-dig polish and the 90% clear aperture. If your application needs a parallelism value for mounting, ask us and we will obtain it from the current specification sheet.
Disclaimer
Specifications on this page are compiled from Thorlabs official published material and are provided as a selection reference only. The current official specification sheet governs; specifications and appearance may change without notice. Commercial terms and lead time are quoted by our sales team on request. Reproduction of this page without written permission is not permitted.
Contact Us
Changsha Soar Laser Equipment Co., Ltd. supplies genuine Thorlabs optics to laboratories and machine builders. For coating selection, aperture sizing, mount matching or lead time on a specific part number, contact us: hotline +86 159 2722 0467, email 859818709@qq.com, or use the enquiry form on www.soar-laser.cn. Tell us the wavelength, the beam diameter at the mirror and the pulse energy or continuous power, and we will confirm whether this coating is the right one before you order.









Reviews
There are no reviews yet.