QQ: 859818709

Thorlabs PF07-03 Ø19 mm Fused Silica Mirror Blank, 6.0 mm Thick, Uncoated

Thorlabs PF07-03 Ø19 mm Fused Silica Mirror Blank, 6.0 mm Thick, Uncoated

Price on request
Category:

Description

Product Overview

PF07-03 is not a mirror. It is the substrate a mirror is made from: a 19.0 mm disc of substrate-grade fused silica, 6.0 mm thick with a tolerance of plus or minus 0.2 mm, front surface better than lambda/10 flat and polished to 10-5 scratch-dig, back surface fine ground and engraved with the item number, clear aperture 90% of the diameter. There is no coating on it, and for that reason there is no reflectance figure anywhere on this page. Any number quoted for an uncoated silica surface would be a bare Fresnel reflection of a few percent per face, which is not a specification, it is an artefact.

The 19 mm size is the reason this part exists. Thorlabs built it specifically to fit its Polaris fixed optic mounts for laser system design and OEM applications, and the design logic is stated plainly on the series page: 19 mm provides a larger clear aperture than a half-inch optic while allowing the mount to keep a one-inch footprint. That is a real mechanical gain. A 12.7 mm disc in the same wall thickness leaves 11.4 mm of aperture; a 19 mm disc leaves 17.1 mm, half again as much, with no change to the bolt pattern or the envelope of the assembly. If your beam has grown past what a half-inch optic can carry and you do not want to redesign the mount, this is the part that solves it.

Fused silica is the material because it transmits from 185 nm to 2.1 µm through 10 mm of glass, which makes the blank usable as a window, a fold substrate or a coating development coupon as well as a mirror body. Its coefficient of thermal expansion is 0.55 x 10-6/degC. That is the number to hold against Zerodur, which sits at 0 plus or minus 0.100 x 10-6/degC and is five and a half times stiffer against thermal drift. Fused silica is entirely adequate for a bench that stays within a few degrees and a beam path of a metre or less; it is the wrong choice when the substrate is bolted to a machine frame that heats during a shift, or when the reflected wavefront has to survive several bounces without walking off a detector.

The surface quality is 10-5 here, against 40-20 on the coated metallic mirrors on the same platform, and that is not an inconsistency. An uncoated polished surface can be delivered at 10-5; once a metal film is deposited, coating defects and the grain of the metal set the achievable scratch-dig, which is why every coated mirror in the family is specified at 40-20. Buy the blank if you need the tighter substrate, and expect the number to relax after coating. Thorlabs also offers lambda/20 flatness as a custom order through technical support, and volume pricing on multiples.

Key Features

  • 19.0 mm diameter: the size Thorlabs designed for Polaris fixed optic mounts, giving 17.1 mm of clear aperture inside a one-inch mount footprint
  • Uncoated: no film, no reflectance specification, and full freedom to specify your own coating or use it as a window
  • 10-5 scratch-dig: a tighter polish than any coated mirror on this platform, which is specified at 40-20
  • Better than lambda/10 flat on the front face, with lambda/20 available as a custom order
  • Fused silica body: transmits 185 nm to 2.1 µm, CTE 0.55 x 10-6/degC, high purity and good environmental durability
  • Fine-ground back with the item number engraved, so identification survives handling and cleaning

Technical Specifications

Parameter Value
Item Number PF07-03
Part Type Mirror blank, uncoated (substrate only)
Material Fused Silica, substrate grade
Diameter 19.0 mm (3/4 inch), +0.0 / -0.1 mm
Thickness 6.0 mm (0.24 inch), plus or minus 0.2 mm
Clear Aperture 90% of the diameter (17.1 mm)
Front Surface Flatness Better than lambda/10 peak to valley; lambda/20 available as a custom order
Front Surface Quality 10-5 scratch-dig
Back Surface Fine ground, item number engraved
Transmission Range 185 nm to 2.1 µm (10 mm sample thickness)
Coefficient of Thermal Expansion 0.55 x 10-6/degC (Zerodur reference: 0 plus or minus 0.100 x 10-6/degC)
Reflectance Not applicable, uncoated substrate
Mounting Interface Polaris fixed optic mounts, one-inch footprint
Source Thorlabs official series specification table

Applications

  • Polaris-based OEM laser systems: the mount is already in the design, the beam has outgrown a half-inch optic, and the 19 mm blank avoids a mechanical redesign
  • Custom coating development: a 10-5 substrate is the right starting point for evaluating a new film, because substrate scatter does not contaminate the measurement
  • Prototype and one-off builds: coat it locally, or have Thorlabs coat it, and iterate without buying a catalogue mirror each time
  • Wavefront reference in a 19 mm mount: an uncoated flat of this figure is a convenient reference surface in an assembly that already uses Polaris hardware
  • UV-visible fold or window substrate: fused silica transmits from 185 nm, so the same part works as a window where a metal mirror would not

Selection Guide

Two decisions: which diameter, and which material. The mount usually answers the first.

  • Polaris fixed mount, one-inch footprint, need more aperture than half an inch: 19 mm, this part. Nothing else in the range does this job.
  • Standard half-inch kinematic or fixed mount: the 12.7 mm PF05-03 blank at 6.0 mm thick, same material and same 10-5 polish.
  • One-inch mount: the 25.4 mm PF10-03 blank, also 6.0 mm thick.
  • Two-inch mount: the 50.8 mm PF20-03 blank, which steps up to 12.0 mm thickness.
  • Thermal drift is the dominant error: switch material to the Zerodur blank, which trades the 185 nm transmission for a CTE five times lower.

Series Comparison

The four fused silica blanks Thorlabs stocks. Diameter and thickness are the only mechanical variables; the polish and figure are common.

Item Number Diameter Thickness Typical Mount
PF05-03 12.7 mm (1/2 inch) 6.0 mm plus or minus 0.2 mm Half-inch kinematic or fixed
PF07-03 19.0 mm (3/4 inch) 6.0 mm plus or minus 0.2 mm Polaris fixed optic mount, one-inch footprint
PF10-03 25.4 mm (1 inch) 6.0 mm plus or minus 0.2 mm One-inch kinematic
PF20-03 50.8 mm (2 inch) 12.0 mm plus or minus 0.2 mm Two-inch kinematic

FAQ

Why does Thorlabs make a 19 mm size at all? Because of the Polaris mount. A 19 mm optic in a mount sized for one-inch hardware gives a larger clear aperture than a half-inch optic while keeping the one-inch bolt circle and envelope, which matters in OEM laser systems where the mechanical layout is fixed and the beam is not. It is a deliberate mechanical compromise between aperture and package size, and it is the reason this diameter appears across Thorlabs mirror, blank and window ranges.

Can I coat it myself? Yes, that is what a blank is for. It is supplied with a 10-5 polished front face specifically so that a coater has a clean starting surface, and Thorlabs offers its own coating services for these substrates as well. Two practical notes: the achievable scratch-dig after metallisation will be 40-20 rather than 10-5, and any coating you add is your specification, not Thorlabs’.

Why is this 10-5 when the coated Zerodur mirrors are 40-20? Because a polished glass surface can be delivered at 10-5 and a deposited metal film cannot. Coating defects, pinholes and the grain structure of the metal set the limit once a film is on the surface. If your requirement is genuinely 10-5 on a finished mirror, you need a dielectric or a superpolished part, not a metal coating on a blank.

Fused silica or Zerodur for my build? Fused silica at 0.55 x 10-6/degC is the right answer for a stable laboratory bench, a short beam path and a moderate power level, and it gives you 185 nm transmission that Zerodur does not. Zerodur at 0 plus or minus 0.100 x 10-6/degC is the right answer when the optic is on a machine that heats, when the beam path is long enough to amplify angular drift, or when the system is a CO2 or amplified Ti:sapphire source.

Usage Precautions

  • It is uncoated, not unprotected. A polished silica face still takes fingerprints, and a fingerprint baked on before coating becomes a permanent defect in the film.
  • Handle by the rim with gloves, and keep the polished face away from the bench surface at all times.
  • Store in a dust-tight container with the polished face up or protected; 10-5 surfaces collect scatter sites from loose dust in a drawer.
  • Do not assume a reflectance. If the application needs a mirror, specify and apply a coating first; an uncoated blank returns only a bare Fresnel reflection per face and is useless as a fold.
  • Check edge chips before coating. A chipped rim is a handling artefact that a coater will not repair, and it can shed particles into the deposition chamber.

Disclaimer

Specifications on this page are transcribed from Thorlabs official public documentation and are provided for selection reference only. The current official specification sheet governs. Thorlabs may change specifications, coatings and appearance without notice. Prices, availability and delivery times are confirmed by our sales team at the time of order; nothing on this page is a binding offer.

Contact Us

Gaofei Laser supplies genuine Thorlabs stock and can quote this item with current availability, lead time and volume pricing. Send the item number, the quantity you need and the wavelength you are working at, and we will confirm the coating, the substrate and the mounting interface before you order.

  • Sales hotline: +86 159 2722 0467
  • Email: 859818709@qq.com
  • Website: www.soar-laser.cn

Reviews

There are no reviews yet.

Be the first to review “Thorlabs PF07-03 Ø19 mm Fused Silica Mirror Blank, 6.0 mm Thick, Uncoated”

Your email address will not be published. Required fields are marked *

中文EN