Description
This is the 10-piece pack of the PF10-03-M03; the optic is identical to the single-unit version.
Product Overview
Ten bare gold discs, each Ø25.4 mm of fused silica and 6.0 mm thick within plus or minus 0.2 mm, with 97 percent average reflectance from 800 nm to 20 µm and no protective overcoat of any kind. Front surface λ/10 at 633 nm, 40-20 scratch-dig, parallelism 3 arcmin or better, clear aperture 90 percent of the diameter at Ø22.9 mm, rear faces fine ground and laser engraved with the item number so a disc that has been separated from its packaging can still be identified.
A part that cannot be cleaned should not be managed like a part that can. If a mirror may not be wiped, then the moment it is contaminated it is finished, and the only remaining question is how quickly it can be replaced. That is the definition of a consumable, and consumables are managed by stocking rate rather than by cleaning schedule. Ten of these turn a maintenance procedure into a swap, and a swap needs no solvent, no lens tissue, no training session and no judgement call about whether the smudge is inside the beam.
The arithmetic behind the quantity is simple. Count the fold points in the beam path, multiply by one and a half, and round up to the nearest pack. A path with six folds needs nine, so one pack of ten covers the machine with one spare; a path with eight folds needs twelve, so two packs cover the machine and leave eight in the cabinet. The factor of one and a half is not superstition: it covers a first-article loss during commissioning, one accidental touch during a service visit, and the ordinary fact that replacements arrive in pairs rather than one at a time.
What this part is not is a way to save money on cleaning. A ten-pack of bare gold costs more than a ten-pack of protected gold, and it buys you a surface that will not survive the first wipe. Buy it because the reflectance or the polarization behaviour requires bare gold, and then treat the box as a box of fuses rather than a box of instruments.
Key Features
- Ten sealed consumables, one part number: the whole fold set can be renewed from one order without a cleaning procedure in the middle of it
- No overcoat, so no cleaning temptation: there is nothing to wipe, and a part that cannot be wiped is a part that gets replaced on evidence rather than on habit
- 97 percent average reflectance, 800 nm to 20 µm: the highest in this format between 800 nm and 2 µm, and flat across the rest of the band
- 1000 W/cm continuous at 10.6 µm: the highest continuous rating in the family, with no overcoat to absorb at long wavelengths
- 4 J/cm² pulsed at 10.6 µm: rated with 100 ns pulses at 1 Hz over a 0.435 mm spot
- Engraved item number on every rear face: the only safe way to identify a bare gold optic, because the identification is on the side you are allowed to look at
- λ/10 at 633 nm across all ten: a batch that behaves as a set when several folds are replaced at once
- Standard Ø1 inch format: drops into the mounts already on the machine, with the caveat about retaining rings noted below
Technical Specifications
| Model | PF10-03-M03-10 | Pack size | 10 pieces |
| Coating | Unprotected gold, bare film, no overcoat | Wavelength range | 800 nm – 20 µm |
| Average reflectance | Ravg over 97 percent | Angle of incidence | 0 – 45 degrees |
| Substrate | Fused silica | Diameter | Ø25.4 mm (1 inch) each |
| Diameter tolerance | +0.0 mm / -0.1 mm | Thickness | 6.0 mm (0.24 in) |
| Thickness tolerance | plus or minus 0.2 mm | Surface flatness | λ/10 PV at 633 nm |
| Surface quality | 40-20 scratch-dig | Parallelism | 3 arcmin or better |
| Clear aperture | 90 percent of diameter | Rear surface | Fine ground, item number laser marked |
| Damage threshold, pulsed | 4 J/cm² at 10.6 µm (100 ns, 1 Hz, Ø0.435 mm) | Damage threshold, CW | 1000 W/cm at 10.6 µm (Ø1.18 mm) |
| Cleaning allowed | None; dry air or nitrogen blow-off only | Mount warning | Retaining-ring mounts are likely to damage the coating |
| Source | Manufacturer published series tables |
Applications
- Sealed laser heads: internal folds that are aligned at build and never opened again, which is the one environment where a bare gold surface is genuinely safe
- OEM machine builds: ten per machine, kitted with the mounts, so the assembly cell never has to decide whether a returned optic is good enough to re-use
- Field-replaceable modules: a service engineer swaps the module and does not attempt to touch the optic inside it
- High-power carbon dioxide paths: 10.6 µm folds at power levels where an overcoat would absorb, up to the 1000 W/cm continuous rating
- Polarization-critical production lines: where the reflected state must be preserved and the line is designed so that nobody reaches the optic during operation
- Labs with rotating operators: a consumable removes the argument about who touched the mirror, because there is no cleaning step to blame
Selection Guide
Size the holding from the beam path, not from the price list. The table is the rule used above, applied to the fold counts that actually turn up on carbon dioxide and fibre machines.
| Fold points in the path | Holding by the 1.5 rule | Buy | What it covers |
|---|---|---|---|
| 2 | 3 pieces | One pack, remainder stored | The path plus a single failure |
| 4 | 6 pieces | One pack | The path, one commissioning loss, one spare |
| 6 | 9 pieces | One pack | The path, one spare, one held back |
| 8 | 12 pieces | Two packs | The path plus eight in the cabinet |
| 10 or more | 15 pieces or more | Two packs or a project quote | Multi-head machines and line installations |
Two conditions override the rule downward. If the head is sealed and never opened, the optic only fails when the laser fails, so one spare is enough. If the machine is opened weekly for process development, the failure rate is set by handling rather than by laser fluence, and the holding should be sized accordingly.
Series Comparison
Bare gold is one of six metal coatings offered in this 25.4 mm format. The column that decides a consumable purchase is the one headed “can it be cleaned”, because that single answer determines whether you are buying spares or buying instruments.
| Pack item | Band | Ravg | Can it be cleaned | Managed as |
|---|---|---|---|---|
| PF10-03-M01-10 | 800 nm – 20 µm | 96% | Yes, gentle solvent wipe | Instrument with spares |
| PF10-03-M02-10 | 2 – 20 µm | 98% | Yes, gentle solvent wipe | Instrument with spares |
| PF10-03-M03-10 | 800 nm – 20 µm | 97% | No, blow-off only | Sealed consumable |
| PF10-03-P01-10 | 450 nm – 20 µm | 97% / 95% | Yes, gentle solvent wipe | Instrument with spares |
| PF10-03-G01-10 | 450 nm – 20 µm | 90% / 95% | Yes, gentle solvent wipe | Instrument with spares |
FAQ
Q: Why would I buy ten of something I am not allowed to clean?
A: Because cleaning is not the only way to deal with contamination. A sealed consumable is dealt with by replacement, and replacement is faster, needs no skill, and leaves no residue. Ten at once is simply the smallest sensible unit for a machine with several folds: it is cheaper per piece than ten singles and it removes the wait between a failure and a restart.
Q: How do I know when one needs replacing?
A: By measurement, not by inspection. Watch the power at the workpiece and the scatter around the head; a contaminated bare gold fold shows up as a slow power loss and a growing halo. Because you cannot inspect the coated face without risking it, the power trend is the only honest indicator, which is another reason to record a baseline when the machine is commissioned.
Q: Can I inspect them on receipt?
A: Look, do not touch. Hold the disc by its rim under oblique light and check for visible film defects, edge chips or packaging debris. Do not wipe a corner to see whether the coating is present, and do not test-fit the optic in a mount before the real installation.
Q: How should the unused ones be stored?
A: In the original slotted case, closed, dry, and away from the machine. Bare gold survives air indefinitely; it does not survive a bench. Let the case reach room temperature before opening it in a humid area, and never stack discs face to face even inside the case.
Q: What happens if a technician touches one during a service visit?
A: Treat it as a loss and replace it. There is no approved cleaning method, so a fingerprint is a permanent change to the local reflectance. The whole point of holding ten is that this decision costs one optic and ten minutes rather than an argument and a purchase order.
Q: Is the engraving still readable after installation?
A: The engraving is on the rear face and stays readable unless the mount covers it, which is why the mount choice matters. Record the position anyway: the engraving tells you what the optic is, not which station it is in, and after a year of swaps only your log can answer the second question.
Usage Precautions
- Keep the case sealed until the machine is open and the mount is ready. A pack that lives on the machine frame is a pack that is contaminated before it is used.
- Gloves or finger cots, rim only, every time. There is no second chance with a bare gold surface.
- No solvent, no lens tissue, no swab, no drag wipe. Dry air or nitrogen is the only permitted action, and only for loose dust.
- Install once. Do not re-seat an optic to check the beam, do not lift it out to inspect the rear, and do not move it after alignment is complete.
- Avoid retaining-ring mounts. The manufacturer warns that they are likely to damage an unprotected gold surface, and a scratched rim is a scratched optic.
- Discard rather than re-use. An optic removed from a machine has an unknown history and cannot be inspected without touching it.
- Record the swap: station, date, reason, and the power reading that triggered it. A consumable programme without a log is just a box of expensive parts.
Disclaimer
Every figure on this page is reproduced from the manufacturer published series tables for selection purposes. Where the official datasheet and this page differ, the datasheet is correct. Coatings, dimensions and markings are subject to change without notice, and pricing and delivery are quoted by our sales desk rather than published here.
Contact Us
Tell us the fold count, whether the head is sealed, and how often the machine is opened, and we will size the holding with you instead of selling you a box. Mixed coatings on one machine are common; if part of the path needs protected gold and part needs bare gold, we will quote the combination and label which is which.








Reviews
There are no reviews yet.