Description
Product Overview
The Thorlabs PF10-03-P01 is a Ø25.4 mm (Ø1 in) plano mirror carrying a protected silver film on a fused silica substrate. Average reflectance is 97% across 450 nm to 2 µm and 95% from 2 µm out to 20 µm. The disc is 6.0 mm thick with a tolerance of plus or minus 0.2 mm, the reflecting face is figured to λ/10 peak to valley at 633 nm and polished to 40-20 scratch-dig, parallelism is held inside 3 arcmin, the clear aperture is 90% of the diameter (Ø22.9 mm), and the part is specified for angles of incidence from 0 to 45 degrees. A laser-engraved item number sits on the fine-ground rear face.
Silver is the highest-reflectance metal film Thorlabs deposits, and the reason is where its absorption bands sit. The interband transitions that pull aluminum down in the blue and flatten gold across the whole visible are pushed deep into the ultraviolet for silver, so from roughly 450 nm upward the metal behaves as a nearly ideal free-electron reflector. The curve is flat enough over 450 nm to 2 µm that the manufacturer can quote one average figure for the whole span, and it remains above 95% out to 20 µm. For a beam path that carries several laser lines at once, 532 nm guidance, a 1064 nm working beam and a 10.6 µm process beam through the same fold, that flatness is worth more than a peak value at a single wavelength.
The Ø1 in format is not a marketing choice, it is the format that most optical mounts were designed around. A 25.4 mm disc seats in the standard retaining ring, in a kinematic mount, in a Polaris fixed mount, in a periscope block, and in the turning mirror position of most commercial scan heads, so the same part number travels between benches. It also buys clear aperture: 22.9 mm of usable surface, against the 10.7 mm a Ø1/2 in optic offers inside the same mount. A 10 mm beam on a half-inch mirror is already clipping at the edge and picking up diffraction from the aperture, which is a problem people usually blame on the laser rather than on the optic. For anything above about 8 mm of beam diameter, this is the sensible size.
Silver’s weakness is chemical rather than optical. It tarnishes in the presence of atmospheric sulfur and darkens in humid air, and both products are absorbing, so an unprotected silver surface degrades from the edge inward within months in a normal laboratory. Thorlabs answers this with a durable SiO₂ overcoat, and that layer is the reason the optic can be handled and cleaned with ordinary optics procedure. It is not an absolute barrier. The manufacturer states directly that high-humidity environments should be avoided, and a bay where condensation forms on cold mounts in the morning is a bay where protected aluminum will outlast this part. Aluminum grows its own passivating oxide beneath its SiO₂ layer and tolerates moisture that silver does not, at the cost of several points of reflectance in the visible and a much lower damage threshold.
One number is worth stating plainly because it is widely misquoted: the flat PF10-03-P01 is specified at 97% average over 450 nm to 2 µm, not 97.5%. The 97.5% figure belongs to other protected silver parts in the catalogue, including the back-side-polished P01P, where the coating is deposited to a slightly different specification. If a link budget is built on 97.5% for this part and the measured value comes back at 97.1%, nothing is wrong with the optic, the budget started from the wrong row. Budget 97% and the arithmetic will hold.
Two damage thresholds are published, and they answer different questions. In pulsed operation the film survives 0.225 J/cm² at 800 nm with 99 fs pulses at 1 kHz over a 0.167 mm spot, and 1 J/cm² at 1064 nm with 10 ns pulses at 10 Hz over a 1.010 mm spot. The femtosecond figure is lower because the peak power is enormous even though the energy is small, which is why ultrafast users should compute fluence rather than average power. In continuous operation the rating is linear: 500 W/cm at 1.07 µm over a 0.974 mm spot and 1500 W/cm at 10.6 µm over a 0.339 mm spot. A linear rating means the permissible total power shrinks with the spot, so a tightly focused beam on this mirror is a far more demanding case than a collimated one of the same wattage.
The band edges matter as much as the middle. Below 450 nm the silver curve falls steeply, so a 405 nm diode or a 355 nm third harmonic is outside the specification and belongs on the UV-enhanced aluminum part. At the long end, 20 µm comfortably covers a 10.6 µm carbon dioxide laser and the 9.4 µm line as well. Between those limits the coating is essentially wavelength-agnostic, which is exactly the property that makes a single part number serve a mixed-wavelength bench.
Key Features
- Highest broadband reflectance of the metal films: 97% average from 450 nm to 2 µm and 95% from 2 µm to 20 µm, flat enough that one optic serves several laser lines without a coating change
- SiO₂ protective overcoat: what keeps the silver from tarnishing and sulfidising, and what makes the surface wipeable with standard solvent-and-tissue procedure
- Fused silica substrate: coefficient of thermal expansion near 0.55 parts per million per degree, so the figure survives warm-up, and good bulk transmission if the rear face is ever used for a ghost measurement
- λ/10 peak to valley at 633 nm with 40-20 scratch-dig: a reflected wavefront clean enough for interferometry, holography and tight focusing downstream
- Ø25.4 mm body, Ø22.9 mm clear aperture: the standard one-inch mount format, with enough coated surface for beams up to about 15 mm without edge diffraction
- 6.0 mm thick, plus or minus 0.2 mm: stiff enough that a three-point seat holds it without inducing figure error, and thin enough for short working distances
- Specified from 0 to 45 degrees: covers the usual 45 degree fold and the small steering offsets either side of it, because metal films are far less angle-sensitive than dielectric stacks
- Pulsed rating at both femtosecond and nanosecond scales: 0.225 J/cm² at 800 nm (99 fs) and 1 J/cm² at 1064 nm (10 ns), so the same part covers an oscillator and a Q-switched pump
- Fine-ground rear face with engraved item number: scatters the rear reflection instead of forming a clean ghost, and makes an unbagged optic identifiable years later
Technical Specifications
| Model | PF10-03-P01 |
| Coating | Protected silver (silver film with SiO₂ protective overcoat) |
| Wavelength range | 450 nm – 20 µm |
| Average reflectance, 450 nm – 2 µm | 97% |
| Average reflectance, 2 – 20 µm | 95% |
| Angle of incidence | 0 to 45 degrees |
| Substrate | Fused silica |
| Diameter | Ø25.4 mm (Ø1 in) |
| Diameter tolerance | +0.0 mm / -0.1 mm |
| Thickness | 6.0 mm (0.24 in) |
| Thickness tolerance | plus or minus 0.2 mm |
| Surface flatness | λ/10 peak to valley at 633 nm over the clear aperture |
| Surface quality | 40-20 scratch-dig |
| Parallelism | 3 arcmin or better |
| Clear aperture | 90% of diameter (Ø22.9 mm) |
| Rear surface | Fine ground, laser engraved with the item number |
| Damage threshold, pulsed 800 nm | 0.225 J/cm² (99 fs, 1 kHz, Ø0.167 mm spot) |
| Damage threshold, pulsed 1064 nm | 1 J/cm² (10 ns, 10 Hz, Ø1.010 mm spot) |
| Damage threshold, CW 1.07 µm | 500 W/cm (Ø0.974 mm spot) |
| Damage threshold, CW 10.6 µm | 1500 W/cm (Ø0.339 mm spot) |
| Mounting | Standard Ø1 in optic mounts, retaining rings and kinematic seats |
| Source | Manufacturer published series specification table |
Applications
This optic is a general-purpose fold, so the useful question is not what it can do but where the silver film is the correct answer rather than merely an acceptable one.
- Mixed-wavelength benches: a table carrying a 532 nm pointer, a 1064 nm fibre laser and a helium-neon alignment beam through the same periscope needs a film that is flat across all three; silver is the only metal coating that answers that without compromise
- Beam delivery and gantry folds: the turning mirrors on a marking or welding gantry see 45 degrees incidence all day and are wiped by operators, so a wipeable film with a 1 J/cm² nanosecond rating is the right balance
- Interferometry and wavefront-sensitive relay: λ/10 at 633 nm with 40-20 polish means the fold does not become the limiting aberration in a Fizeau or Twyman-Green layout
- Spectroscopy and imaging relay: a broadband fold that does not tint the illumination, useful in systems that carry a white-light channel alongside a laser
- Femtosecond oscillator cavities: the 0.225 J/cm² figure at 800 nm with 99 fs pulses covers the intra-cavity fluences of a typical Ti:sapphire oscillator with margin, and the flat band reflects pump and signal together
- Teaching and prototyping: the one-inch format is what students and mounts expect, and a mirror that can be moved between experiments without a new specification keeps a teaching lab running
Selection Guide
Start from the working wavelength, then from the power density, then from the environment. The table below maps the common situations onto the part that actually fits them.
| Requirement | Part | Why that part |
|---|---|---|
| Broadband visible to near infrared fold, general bench use | PF10-03-P01 (this page) | 97% from 450 nm to 2 µm, wipeable, λ/10, one-inch mount format |
| Cost-sensitive fold from 450 nm to 20 µm | PF10-03-G01 | Protected aluminum is the cheapest broadband metal film; it gives up several points of visible reflectance and a much lower damage threshold |
| Infrared work above 800 nm, no visible channel | PF10-03-M01 | Protected gold is flat and slightly higher in the infrared, and it does not tarnish, but it is poor below 800 nm |
| 2 µm to 20 µm with the highest infrared reflectance | PF10-03-M02 | Mid-infrared enhanced gold reaches 98%, at the cost of a much lower pulsed rating |
| Ultraviolet from 250 to 450 nm | PF10-03-F01 | UV-enhanced aluminum with an MgF₂ overcoat; silver is out of specification below 450 nm |
| Fold the beam and sample it at the same time | PF10-03-P01P | Rear face polished to λ/4 so the sub-one-percent leakage can be caught on a photodiode |
| Reflectance above 99% over a narrow band | Dielectric broadband or laser-line mirror | Metal films cannot reach 99%; dielectric stacks can, but only over a restricted band and angle range |
| High humidity or condensing atmosphere | PF10-03-G01 | Aluminum self-passivates; silver’s overcoat slows tarnish but does not stop it |
Sizing follows the beam, not the mount. A useful rule is to keep the 1/e² beam diameter below about two thirds of the clear aperture, which for this optic means 15 mm or less, and to keep it under half if the beam is focused through the fold at a steep angle, because the footprint on a tilted surface stretches by the secant of the incidence angle. At 45 degrees that stretch is a factor of 1.41, so a 10 mm beam covers 14 mm of surface, which still fits inside 22.9 mm but leaves little room for alignment wander.
Series Comparison
The six round one-inch metal coatings, compared on the numbers that decide a purchase: band, average reflectance, whether the film can be cleaned, and the pulsed rating.
| Item | Coating | Band | Ravg | Cleanable | Pulsed rating |
|---|---|---|---|---|---|
| PF10-03-P01 | Protected silver | 450 nm – 20 µm | 97% / 95% | Yes | 1 J/cm² at 1064 nm |
| PF10-03-P01P | Protected silver, rear polished | 450 nm – 20 µm | 96% / 97.5% | Yes | 1 J/cm² at 1064 nm |
| PF10-03-G01 | Protected aluminum | 450 nm – 20 µm | 90% / 95% | Yes | 0.3 J/cm² at 1064 nm |
| PF10-03-M01 | Protected gold | 800 nm – 20 µm | 96% | Yes | 2 J/cm² at 1064 nm |
| PF10-03-M02 | Mid-infrared enhanced gold | 2 – 20 µm | 98% | Yes | 0.1 J/cm² at 1064 nm |
| PF10-03-M03 | Unprotected gold | 800 nm – 20 µm | 97% | No | 4 J/cm² at 10.6 µm |
| PF10-03-F01 | UV-enhanced aluminum | 250 – 450 nm | 90% | Yes | 0.3 J/cm² at 355 nm |
Read the table as a trade, not a ranking. Silver wins on visible reflectance and loses on humidity tolerance. Gold wins on chemical inertness and loses everything below 800 nm. Aluminum wins on price and moisture and loses on reflectance and damage threshold. Unprotected gold wins on damage threshold and loses the right to be cleaned. There is no row that is best everywhere, which is why a machine with a visible pointer and an infrared working beam often needs two different mirrors in the same enclosure.
FAQ
Q: Is the reflectance 97% or 97.5%?
A: 97% average over 450 nm to 2 µm for this part, and 95% average from 2 µm to 20 µm. The 97.5% value that circulates online belongs to other protected silver parts, including the back-side-polished P01P. Quote 97% for PF10-03-P01 and the link budget will match the delivered optic.
Q: Can I clean it, and how often?
A: Yes, within reason. Blow off loose dust with clean dry air or nitrogen, then drag a solvent-moistened lens tissue once across the surface in a single direction, no pressure and no circular rubbing. Do not scrub at a dried droplet and do not make wiping a daily habit; the overcoat is thin and any protected film wears through eventually. If the surface needs cleaning more than a few times a year, the enclosure has a contamination problem worth fixing.
Q: Will it survive my 1064 nm fibre laser?
A: Compare power density, not power. The nanosecond rating is 1 J/cm² at 1064 nm measured over a 1.010 mm spot, and the continuous rating is 500 W/cm at 1.07 µm over a 0.974 mm spot. A 20 W single-mode beam at 50 µm diameter is a far harsher case than a 100 W beam at 5 mm, and the second will run indefinitely while the first will not. Compute the spot on the mirror, including the secant stretch at 45 degrees, before assuming the optic is the limit.
Q: Why is the rear face fine ground rather than polished?
A: Because a polished rear face produces a clean, collimated ghost that can travel a long way and land on a detector or back into a laser. A fine-ground face scatters that same light into a wide cone that dies within a few centimetres. For a fold that only needs to turn a beam, scatter is the desirable behaviour, and it is also cheaper. If you actually want the transmitted light, order the P01P.
Q: Can it be used at 405 nm or 355 nm?
A: Not within specification. The band starts at 450 nm and the silver curve falls steeply below it, so reflectance at 405 nm is well under the quoted average and at 355 nm it is worse still. Use the UV-enhanced aluminum PF10-03-F01 for 250 nm to 450 nm, and accept its lower average reflectance in exchange for a band that actually covers the wavelength.
Q: Does the 45 degree specification mean I can use it at any angle up to 45?
A: It means the reflectance and the wavefront are characterised over that range, so a fold anywhere from normal incidence to 45 degrees is inside the specification. Beyond 45 degrees the s and p curves separate more strongly and the footprint stretches further, so grazing incidence should be treated as a separate design case rather than as a small extension of this one.
Q: Is the engraved number on the front or the back?
A: On the rear, in the fine-ground area. It never touches the working beam and it does not affect the figure. It exists because an unmarked disc that has been taken out of its bag is otherwise unidentifiable, and mixing a protected silver mirror with a protected aluminum one of the same size is a mistake that shows up only as an unexplained loss in the beam path.
Usage Precautions
- Handle by the rim with gloves or finger cots. A fingerprint on a protected silver film leaves an acidic residue that etches into the overcoat, and the local reflectance never fully recovers.
- Keep the optic in its case until the mount is ready. A mirror left on a bench in a workshop collects the workshop, and dust that has settled is far harder to remove without damage than dust that is blown off.
- Use plastic-tipped or nylon retaining rings and tighten only until the disc stops moving. A metal ring tightened onto a 6 mm substrate bends a surface specified at λ/10, and the resulting astigmatism will be blamed on the laser.
- Avoid high-humidity storage and condensing atmospheres. The SiO₂ overcoat slows tarnish but does not seal the silver, and a mirror stored in an unheated room through a wet season will show edge discolouration.
- Do not use acetone on the coated face for extended periods and never let solvent pool at the edge, where it can wick under the coating. Methanol or a proprietary optics solvent on a tissue is the safer habit.
- Account for the rear reflection. The fine-ground rear face scatters rather than forming a clean ghost, but the scatter still goes somewhere, usually into the enclosure wall or back toward the laser, and at high power that is a thermal issue rather than an optical one.
- Record which optic went into which position. When output power drifts three months later, a log that maps item numbers to fold points is the difference between a five-minute diagnosis and a week of swapping parts.
- Inspect under oblique light only. Do not test-clean a new optic to confirm the coating is present; the only way to find out is to remove some of it.
Disclaimer
Specifications on this page are compiled from the manufacturer published series tables and are offered for selection purposes only; the current official datasheet governs. Coatings, dimensions and markings may change without notice. Price and delivery are quoted separately by our sales desk, and the figures above are optical and mechanical specifications, not commercial terms.
Contact Us
Send us the wavelength or wavelength range, the beam diameter at the mirror, the angle of incidence and the power density, and we will confirm whether protected silver is the right film for the whole path or only for part of it. If the layout carries a visible pointer and an infrared working beam through the same fold, say so, because that is the case where one coating usually has to be split into two. Project and bulk quantities are quoted individually.








Reviews
There are no reviews yet.