Description
Product Overview
The AMT 355 15W-500K (model AMT-355-15-500-W) is an Inno Laser AMT series Gen-3 UV picosecond laser: wavelength 355 nm, output power 15 W @500 kHz. It uses an all-in-one design with a newly upgraded control system for more stable operation and versatile control functions. The complete unit combines a fibre seed source with a solid-state amplifier and supports the Advanced POD emission mode and 0–10 V external power control. It is widely used in precision laser micro-machining. Specifications on this page are taken from the official Inno Laser AMT Gen-3 User Manual (V1.0, 2024.03).
Key Features
- All-in-one design: newly upgraded control system, compact footprint, stable operation and multiple control functions
- Advanced POD emission mode: dual assurance of timing stability and pulse-energy stability, trigger response <1 µs, highly uniform pulse energy; compatible with all commercially available motion controllers featuring POD (PSO) functionality
- Multiple trigger modes: TTL signal control (3.5–5 V) with rising-edge, falling-edge, high-level and low-level triggering
- External power-control mode: output power regulated by a 0–10 V DC voltage applied to the DB15 interface; 10 V corresponds to maximum power
- Complete safety design: Class 4 laser with external Interlock, key switch, EMISSION indicator and buzzer alarm
- Rich connectivity: LAN port + RS232 serial port, supplied with the AOC Ultrafast control software (installation-free, supports Windows 7 and later)
Specifications
| Parameter | Value |
|---|---|
| Model | AMT-355-15-500-W |
| Wavelength | 355 nm (UV) |
| Output power | 15 W @500 kHz |
| Laser class | Class IV (GB 7247.1-2012 Class 4) |
| Supply voltage | DC 24 V |
| Operating power | 1000 W |
| Laser weight | 44.3 kg |
| Shipping weight (with packaging) | 69.3 kg |
| Outer-carton dimensions (with base) | 93.6 × 49.2 × 40.8 cm |
Optical parameters such as pulse width, pulse energy, beam quality (M²) and power stability are subject to the Inno Laser factory test report; please contact us for a copy. Inno AMT series picosecond lasers support crystal re-positioning (UV 15 W / 30 W models): beam quality and pointing remain unchanged after the crystal is re-positioned.
Operating Requirements
| Operating Environment | |
|---|---|
| Ambient temperature | 15 °C – 35 °C |
| Relative humidity | 20% – 80% (non-condensing) |
| Altitude | Below 3000 m, away from vibration sources |
| Chiller Requirements | |
| Cooling capacity | 1000 W |
| Temperature stability | ±0.1 °C |
| Water pressure | 18–24 psi (excessive pressure compresses the cavity and causes power degradation) |
| Flow rate | 2–4 L/min |
| Water temperature set point | 22 °C (never adjust the water temperature during operation to optimise power) |
Interface Overview
| Interface | Function | Interface | Function |
|---|---|---|---|
| POWER | Power button | GATE/TRIGGER IN | Trigger signal input |
| KEY | Key switch | SYNC OUT | Synchronisation signal output |
| 24V DC | DC-24 V supply | FLOW IN/OUT | Water inlet / outlet |
| LAN | Ethernet communication | EMISSION | Emission indicator |
| RS232 | Serial communication | INTERFACE | INTERLOCK interlock and external power control |
Start-up and Operating Notes
- Standard start-up sequence: press POWER → wait 10 s → turn the key → connect the software → Laser ON for automatic warm-up (about 7 minutes) → select Low Level Gate mode → set the trigger mode after beam alignment; after 30 minutes of full-power warm-up the laser is ready for processing at working power
- Standard shut-down sequence: Laser OFF (automatic shut-down takes about 60 s) → Shutter OFF → turn the key → wait 10 s → press POWER; an unexpected power cut may cause power degradation and requires power re-optimisation by an engineer
- Supplied accessories: 2 water hoses, 15-pin Interlock connector, DC-24 V power cable, 4 port plugs, 2 keys, handle removal instructions
Quick Troubleshooting Guide (from the official manual)
| Symptom | Checks |
|---|---|
| Deteriorated spot on the workbench | Verify the Report parameters against the factory report; inspect the field lens, beam expander, focusing lens and mirrors for contamination or damage (removing the window is not recommended on picosecond lasers) |
| No emission | Check the alarm code; test with the signal cable unplugged in low-level mode; check the emission signal and supply voltage |
| Power degradation | Confirm the control-signal voltage, window condition and all temperatures; on UV/green models the crystal temperatures (Cry1/Cry2) can be optimised via the software Advanced interface |
If an alarm occurs, do not power off first: connect the software and click Print Report to generate a TXT report, or query the alarm code with the “?STA” command, then follow the alarm table in Chapter 8 of the manual.
Applications
- Precision laser micro-machining: cutting, drilling and scribing of brittle materials (glass, sapphire, ceramics)
- Semiconductor industry: wafer processing and photomask repair
- Medical devices: stent cutting and precision tube machining
- Scientific research: ultrafast laser experimental platforms
📎 Documents
Inno Laser AMT Gen-3 User Manual (PDF, V1.0, 2024.03) — laser safety rules, interface description and accessory list, installation and water-cooling requirements, AOC Ultrafast control software, start-up/shut-down procedures, Advanced POD mode details and troubleshooting procedures.
Source: official manual from Inno Laser Technology Co., Ltd. For selection advice, contact Changsha Soar Laser Equipment Co., Ltd. on +86 159 2722 0467.
Q: What is the Advanced POD mode for?
A: POD (Pulse-On-Demand, also called PSO) emits each pulse only when the motion controller requests it. The trigger response is <1 µs and pulse energies are highly uniform, which is essential for high-quality marking, drilling and scribing on galvo or scan systems.
Q: Which chiller should I pair with the AMT 355 15W-500K?
A: Use a chiller with at least 1000 W cooling capacity, ±0.1 °C temperature stability, 2–4 L/min flow and 18–24 psi water pressure. Set the water temperature to 22 °C and never change it during operation; excessive pressure compresses the cavity and degrades output power.
Q: Can the output power be controlled externally?
A: Yes. Apply a 0–10 V DC signal through the DB15 interface: 10 V corresponds to maximum power, and lower voltages scale the output proportionally. TTL triggering (3.5–5 V) with four trigger modes is also supported.
Pricing and Selection Support
For pricing, stock availability and application support on the Inno Laser AMT 355 15W-500K, contact Changsha Soar Laser Equipment Co., Ltd. on +86 159 2722 0467 (also on WeChat) or e-mail 859818709@qq.com. We supply the full Inno Laser ultrafast range together with scanning systems and process support.




Reviews
There are no reviews yet.