Description
Product Overview
Plenty of working machines never got a fieldbus, and the RS485 version of the DAM + VBA-a exists for exactly that floor. It is the same integrated board that does AI visual beam centring and height follow, built with an RS485 interface so it can be dropped into a control architecture that predates EtherCAT. The alignment routine is unchanged: the red guide beam is imaged, the offset is computed and the DAM module pulls the beam back to centre automatically, so the operator no longer spends minutes at the nozzle with a screen and a screwdriver. Height follow comes from the DAM capacitance loop and is integrated on the same board, which keeps the retrofit to one device instead of two.
The unit suits machine builders and retrofit shops that are keeping their existing controller and want automatic centring without rebuilding the electrical architecture.
Key Features
- RS485 interface: connects to conventional control architectures, including controllers that have no fieldbus at all
- AI visual centring: the red beam is located by vision and corrected automatically, which takes the operator out of the alignment loop
- Height follow: the DAM capacitance follow loop is integrated on the same board, so stand-off control comes with the centring function
- Retrofit friendly: built for upgrading machines already in service rather than for new builds only
- Same function set as the EtherCAT version: the difference is the interface, not the alignment job the board performs
Technical Specifications
| Parameter | Specification |
|---|---|
| Brand | Empower / RayTools |
| Model | DAM+VBA-a (RS485) |
| Type | integrated beam centring and height-follow electronics board |
| Interface | RS485 |
| Scheme | AI vision servo |
| Functions | VBA beam centring plus DAM height follow |
The manufacturer sheet for the RS485 version lists the interface, the scheme and the function set. It does not publish the alignment tolerance, the board dimensions or the supply current as fixed values, so they are not quoted here. Ask us for the current datasheet with your controller model, and we will return the numbers for the exact revision supplied.
Series Comparison
| Model | Function | Communication | Note |
|---|---|---|---|
| DAM+VBA-a (RS485) | automatic | RS485 | centring plus height follow |
| DAM+VBA-a (EtherCAT) | automatic | EtherCAT | centring plus height follow |
| VBA | vision recognition only | Wi-Fi | calibration only, no auto centring |
The RS485 board is the retrofit route: it fits machines whose controller has a serial port and no bus master, and it avoids a controller upgrade just to gain automatic centring. The EtherCAT board is the new-build route, where the unit becomes a node on the machine bus and the alignment is triggered from the program. The plain VBA only measures; it does not correct.
Applications
Retrofit and upgrade of cutting machines already in service: automatic beam centring and height follow on existing gantries, on machines with older controllers, and on mixed fleets where a serial interface is the only common ground. Also used on OEM builds that deliberately keep a simple serial control layer.
Selection Guide
Start from the controller, not from the head. If the machine has an RS485 port and the existing control architecture is to be kept, this version is the one that fits, and the retrofit stays inside the cabinet wiring that is already there. If the controller is bus-based or is being replaced, take the EtherCAT version instead, because it puts the unit on the machine bus and allows the alignment to be programmed and logged. Before ordering, confirm the port, the protocol settings and the head the unit will be fitted to.
Usage Precautions
- Never look into the beam or at specular reflections while the machine is running. Mark the hazard area, fit guards and wear eye protection rated for the wavelength in use.
- On a water-cooled machine, use purified or deionised water and change it on schedule. Stop and investigate when temperature or flow alarms appear, then restart.
- Electrical wiring and service work must be done by a qualified electrician with the supply locked out and tagged. The machine must be reliably earthed against leakage and interference.
- Keep the unit dry and dust-free in transit and in storage. Drain the water circuit, isolate the power and cover the machine before a long shutdown.
- Provide the cabinet ventilation specified for the drives and the control electronics, fit duct filters in dusty shops, and back up the controller parameters regularly.
- On receipt, check the model plate and the accessory list against the order. Contact Changsha Soar Laser support on +86 159-2722-0467 for remote or on-site help during installation and commissioning.
FAQ
Can it go on a machine that has no fieldbus at all? Yes, that is the case it is built for. The RS485 port is the only control link required, so a controller with a serial interface can drive the alignment cycle without a bus master or a controller upgrade.
How long does one alignment cycle take? The vision stage and the correction run automatically and finish in seconds rather than the minutes a manual routine takes. The exact time depends on the number of correction passes needed to settle inside tolerance.
Is a re-alignment needed after a head swap? Yes, and that is the point of the function: after the head is changed, one command brings the beam back to centre instead of a manual setup procedure.
Disclaimer
Specifications are taken from the manufacturer data current at the time of publication and are subject to change without notice. The RS485 datasheet does not publish a fixed alignment tolerance, so any figure quoted for this version must come from the revision actually supplied. Compatibility with a specific controller and protocol setting is confirmed case by case before shipment.
Contact Us
Changsha Soar Laser Equipment Co., Ltd. supplies this unit with a configuration check against your laser source, your cutting head and your controller. Hotline +86 159-2722-0467, e-mail 859818709@qq.com, www.soar-laser.cn.









Reviews
There are no reviews yet.