QQ: 859818709

Thorlabs PF0511-P01 Ø1/2″ Zerodur Protected Silver Mirror, 450 nm – 20 µm

Thorlabs PF0511-P01 Ø1/2″ Zerodur Protected Silver Mirror, 450 nm – 20 µm

Price on request
Category:

Description

Product Overview

PF0511-P01 is silver on Zerodur, specified at 97% average reflectance from 450 nm to 2 µm and 95% from 2 µm to 20 µm. On the same 12.7 mm body that carries the aluminum and gold coatings, this is the film that delivers the most light where most lasers actually work. Dimensions are 6.0 mm thick plus or minus 0.2 mm, lambda/10 peak to valley at 632.8 nm, 40-20 scratch-dig, 3 arcmin parallelism, 90% clear aperture, engraved item number on the fine-ground back.

Silver holds the highest reflectance of any metal across the visible and near infrared, and the margin is not marginal: over 450 nm to 2 µm this coating averages 97% while protected aluminum on the identical substrate averages 90%. Seven points per reflection is the difference between four bounces costing 28% and four bounces costing 34%, and on a photon-starved measurement it is the difference between a working signal-to-noise ratio and a marginal one. Silver also reaches down to 450 nm, where gold has not started reflecting at all.

The cost of silver is chemistry. Silver tarnishes, and a tarnished silver mirror loses reflectance in exactly the band it was bought for. Thorlabs applies a durable SiO2 overcoat roughly 100 nm thick for precisely this reason, and still advises that high humidity environments be avoided. Read those two statements together and the application envelope becomes clear: a dry, temperature-controlled instrument or a sealed head is ideal, an open wet process area is not, and a rinse station next to the optic is out of the question.

Thorlabs also names this coating as well suited to femtosecond pulsed lasers, on the strength of its reflectance across 450 nm to 20 µm, and publishes laser ratings of 1 J/cm2 at 1064 nm for 10 ns pulses and 1500 W/cm CW at 10.6 µm. One documentation note for buyers who compare tables: the mirror series table gives 97% for this coating over 450 nm to 2 µm, while the coating capability table in Thorlabs’ optics documentation lists 96.5% for the same -P01 film with footnotes attached. Treat 97% as the design figure and 96.5% as the conservative one; the difference will not change a system design.

Key Features

  • 97% average, 450 nm to 2 µm: the highest visible and near-infrared reflectance in the metallic Zerodur family, seven points above protected aluminum
  • Still 95% out to 20 µm: one optic serves a 532 nm pump and a 10.6 µm process beam in the same fold
  • 100 nm SiO2 overcoat: the barrier that stops silver from sulphiding and going brown
  • Zerodur substrate: 0 plus or minus 0.100 x 10-6/degC for builds where a warm frame must not walk the beam
  • Femtosecond capable: named by Thorlabs as suited to ultrafast sources on the strength of its broadband reflectance
  • Laser rated: 1 J/cm2 at 1064 nm for 10 ns, 1500 W/cm CW at 10.6 µm, the highest CW figure of the three protected coatings

Technical Specifications

Parameter Value
Item Number PF0511-P01
Coating Protected Silver (silver plus SiO2 overcoat, approximately 100 nm)
Wavelength Range 450 nm to 20 µm
Average Reflectance 97% from 450 nm to 2 µm; 95% from 2 µm to 20 µm
Angle of Incidence 0 to 45 degrees
Substrate Zerodur (Schott registered trademark, substrate grade)
Diameter 12.7 mm (1/2 inch), +0.0 / -0.1 mm
Thickness 6.0 mm (0.24 inch), plus or minus 0.2 mm
Clear Aperture 90% of the diameter
Front Surface Flatness lambda/10 peak to valley at 632.8 nm
Surface Quality 40-20 scratch-dig
Parallelism 3 arcmin maximum
Coefficient of Thermal Expansion 0 plus or minus 0.100 x 10-6/degC
Back Surface Fine ground, item number engraved
Pulsed Damage Threshold 0.225 J/cm2 at 800 nm, 99 fs, 1 kHz, over 0.167 mm; 1 J/cm2 at 1064 nm, 10 ns, 10 Hz, over 1.010 mm
CW Damage Threshold 500 W/cm at 1.07 µm over 0.974 mm; 1500 W/cm at 10.6 µm over 0.339 mm
Source Thorlabs official series specification table

The femtosecond entry in that table deserves attention. 0.225 J/cm2 at 800 nm for 99 fs pulses is a very different number from the nanosecond rating beside it, and it is the one that applies if the source is an amplified Ti:sapphire.

Applications

  • High-power visible and near-infrared delivery: 532 nm and 1064 nm folding in machines where aluminum would waste a tenth of the beam at every bounce
  • Femtosecond amplifier chains: fold and stretcher mirrors, with the 800 nm femtosecond rating as the design limit rather than the nanosecond one
  • Laser display and beam combining: RGB paths where the visible band is the whole point and every percent of green and blue counts
  • LiDAR and range finding: 905 nm and 1550 nm transceiver optics, usually in a sealed housing which is exactly where silver belongs
  • Precision metrology: interferometric stages and encoder heads on machines whose frame warms up during the shift

Selection Guide

Silver is the visible-and-near-infrared answer. Everything else on this platform is a different question with a different answer.

  • Working between 450 nm and 2 µm, want maximum light: this item.
  • Working below 450 nm: the UV-enhanced aluminum -F01 covers 250 nm to 450 nm at 90%; silver has no reflectance there worth having.
  • Working beyond 2 µm, cost sensitive: protected aluminum -G01 still gives 95% from 2 µm to 20 µm and is the cheaper part.
  • Working beyond 2 µm, want maximum light: protected gold -M01 at 96% across 800 nm to 20 µm, or the mid-infrared enhanced -M02 at 98% from 2 µm up.
  • 45 degree incidence with defined s and p values: the ultrafast-enhanced silver -AG is specified at 99.0% s and 98.5% p at 45 degrees over 750 nm to 1 µm, which is a different product for a different job.

Series Comparison

Visible and near-infrared candidates side by side. The silver row is the only one that is both above 95% and broadband in this range.

Coating Band Average Reflectance Positioning
-F01 UV Enhanced Aluminum 250 nm to 450 nm 90% Ultraviolet only
-G01 Protected Aluminum 450 nm to 20 µm 90% / 95% Widest band, lowest cost, humidity tolerant
-P01 Protected Silver 450 nm to 20 µm 97% / 95% Brightest visible and near infrared metal
-AG Ultrafast Enhanced Silver 750 nm to 1 µm 99.0% s / 98.5% p at 45 degrees Polarization-resolved, narrow band

FAQ

Why is silver brighter than aluminum in the visible? Because aluminum has an interband transition that pulls its reflectance down through the visible and only recovers in the infrared, while silver is already close to its peak at 450 nm. That is the entire seven-point gap, and it is why silver-coated mirrors are the standard choice for visible laser delivery despite costing more and tarnishing faster.

Will the overcoat stop it from tarnishing? It slows tarnishing substantially and it is the reason the coating is usable at all, but Thorlabs still says high humidity environments should be avoided. Silver sulphides in the presence of sulphur compounds and moisture; a 100 nm oxide layer reduces the diffusion rate, it does not eliminate it. In a sealed housing the part is effectively permanent; on an open bench in a humid climate it is a consumable.

Is 97% enough for a femtosecond system? For throughput, yes; the question is pulse integrity. A protected coating is a thin-film stack, so it adds dispersion, and Thorlabs nevertheless lists protected silver as well suited to femtosecond sources on the strength of its broadband reflectance. For a few bounces in an amplifier that is normally acceptable and is compensated in the stretcher. For a chirped-pulse chain with a tight dispersion budget, unprotected gold -M03 avoids the question entirely.

How should it be cleaned? Blow off dust, then a single solvent drag wipe with reagent-grade solvent and a fresh lens tissue. Do not scrub, and do not use polymer peel films on a silver coating: the overcoat is thin and the metal below it is soft.

Usage Precautions

  • Keep the optic dry. Condensation and sulphur-bearing atmospheres are the two things that shorten the life of a silver coating, and neither shows up until the reflectance has already dropped.
  • Clean sparingly and gently. Every wipe removes a little of the overcoat, and the overcoat is what stands between the silver and the air.
  • Store in a sealed container with a desiccant, not in a drawer with the rest of the loose optics.
  • Respect the femtosecond rating, not the nanosecond one, if the source is ultrafast: 0.225 J/cm2 at 800 nm for 99 fs is a much lower ceiling than 1 J/cm2 at 1064 nm.
  • Check the beam stays inside the 90% clear aperture; silver at the rim of a coated disc is where coating thickness uniformity and tarnish both start to vary.

Disclaimer

Specifications on this page are transcribed from Thorlabs official public documentation and are provided for selection reference only. The current official specification sheet governs. Thorlabs may change specifications, coatings and appearance without notice. Prices, availability and delivery times are confirmed by our sales team at the time of order; nothing on this page is a binding offer.

Contact Us

Gaofei Laser supplies genuine Thorlabs stock and can quote this item with current availability, lead time and volume pricing. Send the item number, the quantity you need and the wavelength you are working at, and we will confirm the coating, the substrate and the mounting interface before you order.

  • Sales hotline: +86 159 2722 0467
  • Email: 859818709@qq.com
  • Website: www.soar-laser.cn

Reviews

There are no reviews yet.

Be the first to review “Thorlabs PF0511-P01 Ø1/2″ Zerodur Protected Silver Mirror, 450 nm – 20 µm”

Your email address will not be published. Required fields are marked *

中文EN