Description
Product Overview
The PF1011-P01 is protected silver on a 25.4 mm (1 inch) Zerodur® disc, specified at 97% average reflectance from 450 nm to 2 µm and 95% average reflectance from 2 µm to 20 µm. The substrate is 6.0 mm (0.24 in) thick to within plus or minus 0.2 mm, figured to lambda/10 peak to valley at 632.8 nm, polished to 40-20 scratch-dig, parallel to within 3 arcmin, with a clear aperture of 90% of the diameter (Ø22.9 mm) and a fine-ground back face carrying the item number. Zerodur® is a registered trademark of Schott; the glass-ceramic holds 0 plus or minus 0.100 x 10-6/°C against 0.55 x 10-6/°C for fused silica.
Silver is the highest-reflectance metal in the visible and near infrared, and on this coating the margin over the alternative is large enough to change what a machine can do. Over 450 nm to 2 µm the film averages 97%; protected aluminum on the identical body averages 90%. Seven percentage points per reflection is not a datasheet curiosity. On a 10 W visible source it is 0.7 W that either reaches the workpiece or becomes heat in the mirror, and over a four-mirror relay the difference compounds: 88.5% of the beam survives four silver folds against 65.6% through four aluminum ones, a gap of 22.9 percentage points.
The applications where that matters are the ones where the source is expensive per watt and the process is marginal. Green and blue laser processing of copper and brass runs at 532 nm or 515 nm, where the absorption of the metal being marked is high and every photon delivered counts. Fluorescence excitation in microscopy is photon-starved by definition: a 7% loss at each dichroic or fold is 7% less signal, and no amount of post-processing puts it back. Visible laser display and projection systems split and recombine three colours through several folds, and the efficiency of the combiner is the brightness of the product.
Silver pays for that efficiency with chemistry. The metal reacts with sulphur compounds in the air to form silver sulphide, which is dark, and a tarnished silver mirror loses reflectance in exactly the band it was chosen for. That is why bare silver is not a product – it is a laboratory curiosity with a shelf life – and why this part carries a silicon dioxide overcoat. The overcoat is what makes the film usable: it slows the tarnishing, it is hard enough to survive a solvent drag wipe, and it lets the optic be cleaned rather than replaced. Thorlabs still rates protected aluminum as less likely to tarnish in a high humidity environment, so the overcoat slows the process rather than stopping it, and a silver mirror in a damp room is a maintenance item rather than a permanent fixture.
Above 2 µm silver drops to 95% average, which is a point below protected gold and two below bare gold. It is not a mid-infrared coating: on a CO2 bench the gold parts are both brighter and more stable. Silver owns 450 nm to 2 µm and should be specified there.
Zerodur® is the right substrate here for a reason specific to visible high-power work. A frequency-doubled Nd:YAG at 532 nm or a frequency-doubled fibre source at 515 nm is usually the highest-brightness visible laser in the building, and the mirror absorbs a few percent of it – the same few percent in absolute terms as an infrared beam, but a larger fraction of a beam that is already harder to generate. On a 25.4 mm disc the absorbed power is four times what the same irradiance would deposit in a half-inch optic, so the substrate term in the thermal drift budget grows with the format. Zerodur removes it.
Key Features
- 97% average from 450 nm to 2 µm: the highest visible and near-infrared reflectance in the family, seven points above protected aluminum over the same band
- Silicon dioxide overcoat: slows the sulphide tarnishing that destroys bare silver and makes the surface cleanable, which is the only reason a silver optic is a product rather than a consumable
- 95% average from 2 µm to 20 µm: still usable in the near infrared, though gold is the better choice beyond about 2 µm
- Zerodur® body at 0 plus or minus 0.100 x 10-6/°C: protects focal stability on a 25 mm disc carrying a high-brightness 532 nm or 515 nm beam
- Lambda/10 figure, 40-20 polish, 3 arcmin parallelism: a wavefront budget that supports imaging and interferometric use, not only beam steering
- Published laser ratings including femtosecond data: 0.225 J/cm2 at 800 nm in 99 fs pulses and 1 J/cm2 at 1064 nm in 10 ns pulses
Technical Specifications
| Parameter | Value |
|---|---|
| Item Number | PF1011-P01 |
| Coating | Protected Silver (silver film plus SiO2 overcoat) |
| Wavelength Range | 450 nm to 20 µm |
| Average Reflectance | 97% from 450 nm to 2 µm; 95% from 2 µm to 20 µm |
| Substrate | Zerodur® glass-ceramic (registered trademark of Schott) |
| Diameter | 25.4 mm (1 in), +0.0 / -0.1 mm |
| Thickness | 6.0 mm (0.24 in), plus or minus 0.2 mm |
| Clear Aperture | 90% of the diameter, Ø22.9 mm |
| Front Surface Flatness | lambda/10 peak to valley at 632.8 nm |
| Surface Quality | 40-20 scratch-dig |
| Parallelism | 3 arcmin maximum |
| Coefficient of Thermal Expansion | 0 plus or minus 0.100 x 10-6/°C (fused silica for comparison: 0.55 x 10-6/°C) |
| Back Surface | Fine ground, item number engraved |
| Pulsed Damage Threshold | 0.225 J/cm2 at 800 nm, 99 fs, 1 kHz, over a 0.167 mm beam; 1 J/cm2 at 1.064 µm, 10 ns, 10 Hz, over a 1.010 mm beam |
| CW Damage Threshold | 500 W/cm at 1.07 µm over 0.974 mm; 1500 W/cm at 10.6 µm over 0.339 mm |
| Tarnish Resistance | Overcoat slows sulphide tarnishing; rated below protected aluminum in humidity |
The 1 J/cm2 nanosecond rating over a 1.010 mm spot is 7.9 mJ per pulse, roughly double the protected aluminum figure, and the 1500 W/cm continuous rating at 10.6 µm is the highest continuous figure in the family. The femtosecond row is the one to read carefully: 0.225 J/cm2 at 99 fs is a low number, and it is telling you something. A silver film with a dielectric overcoat is not the right optic for a sub-picosecond beam – the overcoat is a thin-film stack and a stack is what fails first under femtosecond irradiation. For that regime the bare gold -M03 on the same body is the correct part.
The tarnish row is not a defect either. Silver is chemically active; the overcoat is a barrier, not a seal, and in a sulphur-bearing atmosphere the film will eventually darken. What the overcoat buys is years instead of months, and the ability to wipe the surface without removing the metal.
Applications
- 532 nm and 515 nm processing of copper, brass and reflective metals: high-brightness green sources where the 7% advantage over aluminum is delivered power at the workpiece
- Fluorescence excitation and detection paths: confocal and light-sheet systems where a fold or dichroic at 488 nm or 561 nm sits in a photon-starved chain
- Visible laser display and projection combiners: RGB recombination paths where efficiency sets brightness and thermal load at once
- Harmonic separation and beam conditioning: 450 to 700 nm paths that must also pass or dump the residual 1064 nm without a second optic
- Semiconductor and flat-panel inspection: bright-field illumination relays at 405 to 660 nm where a 10% loss per fold would force a larger source
Selection Guide
Silver is a specialist coating with one narrow winning band and one clear failure mode. Use the questions below to decide whether you are in the band.
- Is the working wavelength between 450 nm and 2 µm? If the answer is no, silver is not the coating; go to protected aluminum for breadth or gold for the infrared.
- Does the process need every photon? If the source is a 10 W visible laser or a fluorescence signal, 7 points per fold is worth having. If it is a 100 mW alignment beam, it is not.
- How many folds are in the path? One fold justifies the coating on efficiency grounds; four folds make it a design decision, because the gap grows from 7 points to 22.9.
- Are the pulses longer than about a picosecond? If not, the overcoat becomes the weak element and bare gold is the correct choice despite the lower visible reflectance.
- Is the environment free of sulphur and condensation? If the bench sits in a damp or industrial atmosphere, plan for periodic inspection of the coating, or accept aluminum and its seven-point penalty.
Series Comparison
One substrate, four films: 25.4 mm diameter, 6.0 mm thick, lambda/10 figure, 40-20 polish, 3 arcmin parallelism, 90% clear aperture. The reflectance column is where the decision is made.
| Coating | Wavelength Range | Average Reflectance | Where It Wins |
|---|---|---|---|
| -G01 Protected Aluminum | 450 nm to 20 µm | 90% / 95% | Widest band, best humidity tolerance, cleanable |
| -M01 Protected Gold | 800 nm to 20 µm | 96% | Infrared power folding, cleanable, angle insensitive |
| -M03 Unprotected Gold | 800 nm to 20 µm | 97% | Ultrashort pulses and polarization purity |
| -P01 Protected Silver | 450 nm to 20 µm | 97% / 95% | Maximum visible and near-infrared throughput, cleanable |
Read the silver row as a trade against its neighbour: it is seven points brighter than aluminum from 450 nm to 2 µm and two points dimmer than bare gold beyond 2 µm, with an overcoat that limits it to nanosecond and longer pulses. Within its band it has no competitor in this family.
FAQ
How much does the 7% actually buy?
On a single fold at 10 W it is 0.7 W of delivered power and 0.7 W less heat in the mount. Across four folds the transmitted fraction goes from 65.6% to 88.5%, which on the same 10 W input is 6.6 W against 8.9 W at the workpiece. That difference is usually worth more than the price gap between the two coatings.
Will the silver tarnish even with the overcoat?
Eventually, in a sulphur-bearing atmosphere. The SiO2 layer is a diffusion barrier, not a hermetic seal, and Thorlabs itself rates protected aluminum as the more humidity-tolerant of the two. In a clean, air-conditioned laboratory the coating lasts for years; in a workshop next to rubber tooling or a plating line it will darken and the reflectance will fall in the blue end first.
Can I clean a protected silver mirror?
Yes – that is the difference between this part and bare silver. Blow off loose dust, then one wet drag wipe with reagent-grade solvent and a lens tissue, then stop. Do not scrub, do not use abrasive polishes, and do not use any silver-dip product on a coated optic.
Why does the reflectance fall to 95% above 2 µm?
Silver’s reflectance in the infrared is limited by its conductivity rather than by a band edge, and the curve eases down gradually. Two points below bare gold is enough to make gold the better choice on a CO2 bench, and the margin widens further in the far infrared.
Can this mirror be used with femtosecond pulses?
It can be used, but it should not be the first choice. Thorlabs rates the protected silver coating at 0.225 J/cm2 for 99 fs pulses at 800 nm, the lowest femtosecond figure in this family, because the dielectric overcoat is what absorbs and fails first. For ultrashort work use the unprotected gold -M03.
Usage Precautions
- Handle by the rim with gloves: silver films mark easily and the overcoat is thin. A fingerprint on a 532 nm fold is a localised absorber at exactly the wavelength the coating was chosen for.
- Clean wet, once, and stop: blow first, one drag wipe, no scrubbing. Repeated wiping thins the overcoat locally and shows up as a reflectance dip that looks like tarnish.
- Keep sulphur out of the enclosure: rubber gaskets, some lubricants, vulcanised fixturing and plating baths all release sulphur compounds. Ventilated enclosures with filtered air extend coating life more than any cleaning routine.
- Do not over-clamp: a snug retaining ring is enough for a 6 mm disc. Distortion from an over-tightened ring is indistinguishable from a bad figure when you measure the wavefront.
- Derate for femtosecond use: if any part of the beam is sub-picosecond, either attenuate or move to a metal-only coating. The overcoat is the failure point.
- Inspect periodically: a silver mirror in service should be checked for darkening at the blue end. A reflectance drop at 450 nm is the first sign that the film is going.
Disclaimer
Specifications on this page are transcribed from Thorlabs official public documentation and are provided for selection reference only; the current official specification sheet governs. Thorlabs may change coatings, tolerances and appearance without notice. Reflectance is quoted as an average over each range; silver coatings show a gradual roll-off rather than a step, so the value at a specific wavelength can differ from the average. Prices, stock and delivery times are confirmed by our sales team at the time of order, and nothing on this page is a binding offer.
Contact Us
Gaofei Laser supplies genuine Thorlabs stock and quotes this item with current availability, lead time and volume pricing. Send the item number, quantity, wavelength and pulse length, and we will confirm whether protected silver is the right film for your visible path or whether a gold coating serves you better.
- Sales hotline: +86 159 2722 0467
- Email: 859818709@qq.com
- Website: www.soar-laser.cn
- Company: Gaofei Laser, soar-laser.cn









Reviews
There are no reviews yet.