QQ: 859818709

Thorlabs PF15-03-P01 Ø38.1 mm (1.5 in) Protected Silver Mirror, 450 nm – 20 µm

Thorlabs PF15-03-P01 Ø38.1 mm (1.5 in) Protected Silver Mirror, 450 nm – 20 µm

Price on request
Category:

Description

Product Overview

The 1.5 inch mirror is the aperture nobody designs in first and everybody ends up needing. A 25.4 mm mirror looks generous until the beam is 22 mm across: the clear aperture of a Ø1 in optic is 90 percent of its diameter, which leaves 22.9 mm, and the outer millimetre of a Gaussian beam is exactly where the energy that ruins a wavefront sits. The next size up in the catalogue is Ø2 in, and that jump drags a whole chain of consequences with it: a larger kinematic mount, a larger pedestal, more table area, a different post, and a price step that is hard to justify on a bench where the beam is 20 mm wide and no wider.

Ø38.1 mm (1.5 in) sits in that gap and closes it. At the same 90 percent clear aperture rule it delivers 34.3 mm of usable diameter, which comfortably contains a 20 to 25 mm beam with margin at the edge, and it fits the 1.5 inch mirror mounts that most laboratories already own for legacy optics. That is the whole engineering argument for this size, and it is worth stating plainly because the part is often bought for the wrong reason: not because 1.5 inch is a standard, but because it is the smallest aperture that stops clipping a two-centimetre beam.

The PF15-03-P01 is the protected silver version of that mirror. The substrate is fused silica, chosen for a coefficient of thermal expansion of 0.55 × 10⁻⁶ per degree Celsius and for the polish quality that fused silica takes. The coating is silver with a silicon dioxide overcoat roughly 100 nm thick, designated by the -P01 suffix. Average reflectance is over 97 percent from 450 nm to 2 µm and over 95 percent from 2 to 20 µm, which makes this the highest reflectance metallic coating in the visible to near infrared across the Thorlabs range, and it is the reason the part is popular in femtosecond work where every percent of throughput matters.

Surface figure is lambda/10 peak to valley at 633 nm and surface quality is 40-20 scratch-dig, both measured on the coated surface. The clear aperture is 90 percent of the diameter. The rear face carries the model number, as it does on all Thorlabs mirrors of Ø1/2 in and above, so a mirror that has been separated from its packaging can still be identified.

One practical point about the thickness. The family specification page lists four substrate thicknesses across eight part numbers rather than one thickness per part, and the Ø1.5 in row falls inside a merged cell. No single value can therefore be quoted honestly for this size. The dimension is available on the CAD and STEP models, and it should be read from there before a mount, a retaining ring or a clamp is designed around it.

Key Features

  • 1.5 inch aperture with 34.3 mm clear aperture. The smallest standard size that holds a 20 to 25 mm beam without clipping at the edge.
  • Protected silver coating, -P01. Silver for maximum reflectance, with a silicon dioxide overcoat of roughly 100 nm to slow the tarnishing that otherwise destroys a bare silver film in months.
  • Average reflectance over 97 percent from 450 nm to 2 µm, over 95 percent from 2 to 20 µm. One optic covers the argon, helium-neon, diode, Nd:YAG, erbium and CO2 bands without a coating change.
  • Fused silica substrate, CTE 0.55 × 10⁻⁶ per degree Celsius. Low enough that a mirror warmed by a few watts of stray light does not walk the beam.
  • Lambda/10 peak to valley at 633 nm. Adequate for interferometry and for beam transport ahead of a focus, where a poorer figure would show up as an asymmetric spot.
  • 40-20 scratch-dig. Tight enough for imaging and for beam-profiling pick-offs, and a realistic specification for a 38 mm polish.
  • Diameter tolerance +0.0 / -0.1 mm. A one-sided tolerance, so a mirror is never oversize for its mount bore; it is always a light clearance fit.
  • Published laser damage thresholds. Both pulsed and continuous-wave figures are given for defined spot sizes, so the limit can be scaled rather than guessed.
  • Rear-engraved model number. Identification survives separation from packaging, which matters in a shared optics store.

Technical Specifications

Parameter Specification
Model PF15-03-P01
Coating suffix meaning -P01, protected silver
Diameter 38.1 mm (1.5 in)
Diameter tolerance +0.0 / -0.1 mm
Substrate material Fused silica
Coefficient of thermal expansion 0.55 × 10⁻⁶ per degree Celsius
Coating Protected silver, silver film with silicon dioxide overcoat
Overcoat thickness Approximately 100 nm of silicon dioxide
Average reflectance, 450 nm to 2 µm Over 97 percent
Average reflectance, 2 µm to 20 µm Over 95 percent
Surface figure Lambda/10 peak to valley at 633 nm
Surface quality 40-20 scratch-dig
Clear aperture 90 percent of diameter, 34.3 mm
Thickness Not published as a single value on the family specification page. Download the CAD / STEP drawing for the exact substrate thickness. Diameter tolerance is +0.0 / -0.1 mm.
Rear surface Not specified as polished. Select the -P01P variant if a polished rear face or rear-side sampling is required.
Identification Model number engraved on the rear face
Pulsed damage threshold, femtosecond 0.225 J/cm² at 800 nm, 99 fs, 1 kHz, spot diameter 0.167 mm
Pulsed damage threshold, nanosecond 1 J/cm² at 1064 nm, 10 ns, 10 Hz, spot diameter 1.010 mm
CW damage threshold, near infrared 500 W/cm at 1.07 µm, spot diameter 0.974 mm
CW damage threshold, far infrared 1500 W/cm at 10.6 µm, spot diameter 0.339 mm

The four damage threshold entries are quoted exactly as published, including the spot diameter that belongs to each. That detail is not housekeeping: the two continuous-wave numbers differ by a factor of three, but they were measured with spots of 0.974 mm and 0.339 mm, so converting each to total power gives approximately 49 W and 51 W. The thresholds are consistent with each other once the spot size is accounted for, and comparing 500 with 1500 directly would be a mistake.

The same caution applies to the pulsed figures. Converting the femtosecond entry at its 0.167 mm spot gives roughly 49 microjoule per pulse, while the nanosecond entry at 1.010 mm gives roughly 8.0 millijoule. Both are correct as published and neither can be transferred to a different spot size without scaling, because damage in a dielectric overcoat is driven by fluence, by pulse duration and by the number of pulses.

Applications

Femtosecond beam transport. The 450 nm to 20 µm bandwidth and the high average reflectance make this a natural turning mirror in a chirped-pulse amplifier bench, where a chain of six or eight reflections is normal and each percent of loss is paid twice, once on the way in and once on the way out. The 100 nm silicon dioxide overcoat is thin enough that its contribution to group delay dispersion is small, but it is not zero, and a design that depends on dispersion balance at the few-femtosecond level should account for it rather than assume it away.

Multi-wavelength benches. A laboratory that runs a 532 nm pump, a 1064 nm probe and a mid-infrared source can use one coating on all three paths. That removes the most common cause of a misplaced optic in a shared lab, which is a mirror that looks identical to its neighbour but carries a different coating.

Interferometry and wavefront sensing. Lambda/10 at 633 nm is a specification for the coated surface at a single wavelength; at 1550 nm the same physical surface error corresponds to a smaller fraction of a wave, so the optic performs better in the infrared than the number suggests. This is one of the few places where a visible-wavelength specification is conservative.

Beam expansion and relay telescopes. A 38 mm mirror at the output of a two-lens expander is a common arrangement, and the clear aperture of 34.3 mm leaves room for the beam to breathe as the expander is tuned. Using a Ø1 in mirror in the same position is the mistake that produces a beam with a clipped edge and a diffraction ring that is blamed on the lens.

Prototype and one-off builds. Where a design calls for a mirror of about 40 mm and the mechanical package is already drawn around a 1.5 inch mount, this part avoids redesigning the mount to accept a 2 inch optic. That is a schedule argument rather than an optical one, and on a prototype it is usually the argument that decides.

Selection Guide

Three questions settle the choice, and they are best answered in this order.

  • Is the beam wider than 22.9 mm. If it is, a Ø1 in optic will clip it at the 90 percent clear aperture and the answer is 1.5 inch or 2 inch. If the beam is wider than 34.3 mm, even this optic is too small and the choice moves to Ø2 in.
  • Is the wavelength inside 450 nm to 20 µm. If yes, protected silver is the highest reflectance metal coating available in the visible to near infrared and is normally the right answer. If the work is below 450 nm, silver is the wrong choice and an aluminium coating with a ultraviolet enhancement is required. If the work is beyond 20 µm, protected gold is the appropriate metal.
  • Will the optic see more than a few watts per centimetre. The published continuous-wave limits are 500 W/cm at 1.07 µm and 1500 W/cm at 10.6 µm. Convert the beam to linear power density at the mirror before deciding, and remember that a focused beam at the mirror surface is the usual way these limits are exceeded by accident.

Two secondary considerations are worth a sentence each. If the rear face has to be polished, for a pick-off or for a through-the-mirror alignment return, the -P01P variant is the part to order; the standard -P01 rear face is not specified as polished, and adding a polished back changes both the price and the lead time. If the environment is humid, uncontrolled, or contains sulfur compounds from a nearby process, protected silver is the coating most sensitive to that environment in the entire metal family, and the honest answer may be a dielectric coating even at some cost in bandwidth.

Series Comparison

Nominal size Diameter Clear aperture at 90 percent Typical use
Ø1 in 25.4 mm 22.9 mm Beams up to about 15 mm; the default for compact benches
Ø1.5 in 38.1 mm 34.3 mm This page. Beams of 20 to 25 mm without moving to a 2 inch mount
Ø2 in 50.8 mm 45.7 mm Beams above 30 mm, large-aperture relay and expansion stages

All three apertures are offered in the same protected silver coating family, so the reflectance curves and the environmental caveats carry across. What changes with size is not the coating but the mechanical consequence: mounts, posts, pedestals and table area all step up with the optic, and the 1.5 inch size is the last point in the chain where the mount can still be a common one. The clear aperture column is calculated from the published 90 percent clear aperture rule rather than quoted from a drawing, and it is included because the aperture is the number that actually decides clipping.

FAQ

Q: What is the actual average reflectance of this coating?

A: Average reflectance is over 97 percent from 450 nm to 2 µm and over 95 percent from 2 to 20 µm. A figure about half a percentage point higher than 97 is sometimes quoted for this part; that figure is not the official value for the PF series plano mirror with the -P01 coating. The higher number belongs to other -P01 parts in the catalogue and to the -P01P rear-polished variant, whose rear face also reflects. For this part, use 97 and 95 as the two design numbers.

Q: What is the substrate thickness?

A: There is no single published value for the Ø1.5 in size. The family specification page lists four thicknesses across eight part numbers, and the 1.5 inch row sits inside a merged cell, so any single number attributed to this part is an assumption rather than a specification. Download the CAD or STEP model and read the dimension from the geometry. A thickness of 8 mm is sometimes quoted for this part; that is not the official value either.

Q: Is the back surface polished?

A: The standard -P01 part is not specified as having a polished rear face. If rear-side sampling, a through-the-mirror alignment return, or a polished back for cosmetic reasons is required, order the -P01P variant, which is the rear-polished version of the same coating. Using a standard part in an application that assumes a polished back will produce a scatter signature that no amount of alignment will remove.

Q: Can this mirror be used with femtosecond pulses?

A: Yes, and the published threshold is 0.225 J/cm² at 800 nm with 99 fs pulses at 1 kHz and a 0.167 mm spot. Two cautions. First, scale the fluence to your own spot size rather than comparing energies. Second, the roughly 100 nm silicon dioxide overcoat is a thin film and does contribute group delay dispersion; at pulse durations of tens of femtoseconds this is usually negligible, at sub-ten-femtosecond durations it should be included in the dispersion budget.

Q: Why is the surface figure quoted at 633 nm and not at my wavelength?

A: Because 633 nm is a helium-neon laser line and a convenient, stable, universally available reference. The physical surface error does not change with wavelength; only its expression in waves does. A lambda/10 surface at 633 nm is about lambda/24 at 1550 nm, so the optic is better in the infrared than the specification implies.

Q: How should the coating be cleaned?

A: With a clean, dry, oil-free air bulb first, then dragging a lens tissue moistened with reagent-grade solvent across the surface in one direction, with no pressure and no circular rubbing. Never use an abrasive, never use a dry tissue on a dry surface, and never use acetone on a silver coating that has been in service for years without checking it first. Fingerprints are the main enemy: the salts and acids in a fingerprint attack the protective overcoat and then the silver beneath it.

Q: Can it be used in a humid room?

A: It can be used, but it should not be stored there. The manufacturer states that exposure to high humidity or high temperature degrades the protective layer and lets the silver film oxidise, and that protected silver mirrors should be used and stored at room temperature in a low-humidity environment. A desiccator cabinet is cheap insurance for an optic of this size.

Q: Does the engraved model number affect the optical performance?

A: No. The engraving is on the rear face, outside the clear aperture, and the part is mounted from the front surface in any case. It exists so that a mirror which has lost its packaging can still be identified, which is worth more in a shared store than it costs to apply.

Usage Precautions

  • Handle by the edge only. Gloves or finger cots, and never touch the coated face. A fingerprint left for a week will etch a permanent mark into the overcoat and then into the silver.
  • Keep it dry. Store at room temperature in a low-humidity environment. High humidity and high temperature are the two conditions the manufacturer names as degrading the protective layer and allowing the silver to oxidise.
  • No abrasives, ever. No polishing compound, no abrasive pad, no dry tissue dragged across a dry surface. The overcoat is roughly 100 nm thick and is removed by the first abrasive contact.
  • Check the mount against the drawing before clamping. Because the substrate thickness is not published as a single value, a retaining ring, a clamp or a custom holder must be dimensioned from the CAD model rather than from an assumed thickness. A ring that is 0.5 mm too deep will load the mirror through the coating edge and chip it.
  • Do not over-clamp. A mirror of this diameter and this thickness will bend under a retaining ring that is tightened by feel with a long wrench. Lambda/10 is a surface specification on an unclamped part; a distorted mount turns it into a much worse optic without any visible sign.
  • Respect the spot size behind every threshold. The published damage thresholds are tied to defined spot diameters. A beam focused to 100 µm at the mirror surface raises the fluence by two orders of magnitude compared with the same pulse spread over 1 mm.
  • Watch the rear reflection. The rear face is not specified as polished, but it still reflects a small amount. In a high-dynamic-range measurement, that faint return can appear as a ghost and is usually blamed on the detector.
  • Do not mix this part with its neighbours in a drawer. Several Thorlabs mirrors share the same 38 mm diameter and differ only by coating. Keep the -P01 with its packaging or label the edge, because a protected aluminium mirror and a protected silver mirror are indistinguishable in a dim room.

Disclaimer

Every optical value on this page is reproduced from the manufacturer published specification for the PF series plano mirror with the -P01 coating, and is repeated here so that a design can be checked without opening a datasheet. Where this page and the current datasheet disagree, the datasheet governs. Reflectance, surface figure and damage thresholds are typical or guaranteed values measured under the conditions stated, and they are not a warranty of performance in a specific system. Thickness is deliberately left unresolved because the published table does not resolve it for this size; obtain the CAD model before designing a mount. No price is stated on this page, and availability is confirmed only at the time of quotation.

Contact Us

If a beam is close to the edge of the clear aperture, if a damage threshold needs to be scaled to an unusual spot size or pulse duration, or if the choice between protected silver and a dielectric coating is not obvious for a particular laser, send the wavelength, the beam diameter at the mirror, the average power and the pulse parameters, and the sales team will work through the numbers with you rather than quote a part number and stop there. Requests for the CAD model, for a rear-polished -P01P alternative, or for a quantity price on several mirrors can be handled in the same enquiry.

Reviews

There are no reviews yet.

Be the first to review “Thorlabs PF15-03-P01 Ø38.1 mm (1.5 in) Protected Silver Mirror, 450 nm – 20 µm”

Your email address will not be published. Required fields are marked *

中文EN