QQ: 859818709

Thorlabs PF20-03-M02-10 Ø50.8 mm (2 in) Mid-Infrared Enhanced Gold Mirror, 10-Piece Pack

Thorlabs PF20-03-M02-10 Ø50.8 mm (2 in) Mid-Infrared Enhanced Gold Mirror, 10-Piece Pack

Price on request
Category:

Description

Product Overview

This is the 10-piece pack of the PF20-03-M02; the optic is identical to the single-unit version. Ten 50.8 mm (2 in) mid-infrared enhanced gold mirrors, 12.0 mm thick on fused silica, each specified at 98 percent average reflectance from 2 to 20 µm, each flat to lambda/10 peak-to-valley at 633 nm, each engraved with its part number on the back. The optic does not change. What changes is that the mirror stops being a component you order when one fails and becomes a consumable you hold in stock.

On a CO2 line the mirror is a wear item

Nobody describes a turning mirror as a consumable, and yet in a production CO2 environment it behaves like one. The optic sits in an enclosure where the air carries vapour from the workpiece, fine spatter from the cut, and moisture that condenses when the head cools between shifts. All three land on the coating. Organic compounds polymerise under the beam and build a translucent film. Metal spatter bonds and cannot be dissolved off. Condensed moisture leaves mineral residue when it dries. A surface that measures 98 percent on a bench can be well under 90 percent after a few weeks of that treatment, and it degrades gradually enough that nobody notices.

That gradualness is the actual problem. A mirror that fails suddenly gets replaced. A mirror that loses four points a month gets compensated for by turning the power up, and then by slowing the feed rate, and then by accepting a worse cut edge. By the time somebody checks the optic, the process has been running out of specification for a quarter and the scrap has already been booked.

Making the swap a scheduled action instead of an incident

Ten mirrors on the shelf changes the decision. A replacement is no longer a purchase order with a lead time and an approval; it is a box in the cabinet. The swap can be planned into a shift change, the removed optic can be inspected and either cleaned or retired, and the process does not have to stop for a week while purchasing catches up. This is the whole argument for holding a pack, and it is a maintenance argument, not a discount argument.

Why the overcoat matters more here than in a laboratory

An unprotected gold surface is soft and cannot be cleaned. In a sealed laboratory enclosure that is an acceptable compromise for the extra point of reflectance. In a CO2 head it is not, because the surface will get dirty and the only remedy available for bare gold is replacement. The dielectric overcoat on this coating allows reagent-grade solvent cleaning with lens tissue, which means a lightly contaminated optic can be recovered instead of scrapped. On a production line the ability to clean is worth more than one percent of reflectance.

What the pack does not do

It does not lower the specification, it does not select a lower grade, and it does not make the mirror resistant to damage. A scratched coating is still a scratched coating, and a mirror installed with the coated face toward the mount will still fail. The pack buys availability and lot consistency, nothing else.

Key Features

  • Ten M02 optics, one lot – a stocked replacement set for CO2 delivery paths, drawn from a single coating run so a new optic matches the one it replaces.
  • 98 percent average reflectance, 2 to 20 µm – the thermal-infrared optimised coating, four points above the broadband protected gold at the CO2 line.
  • 3 J/cm² at 10.6 µm, 100 ns – about 39 mJ of pulse energy on the 1.29 mm test spot, adequate for pulsed CO2 sources as well as CW.
  • 450 W/cm CW at 10.6 µm – roughly 53 W of total power on the 1.18 mm test spot; scale with your own beam diameter.
  • Cleanable dielectric overcoat – the property that makes a dirty production optic recoverable rather than scrap.
  • Pack size: 10 mirrors – one pack equips a small multi-head line and leaves a service set in the cabinet.
  • 50.8 mm diameter, 12.0 mm thick, 45.7 mm clear aperture – standard 2 inch mounting, with the thermal mass to hold figure under tens of watts.
  • Lambda/10 peak-to-valley at 633 nm, 40-20 scratch-dig, 3 arcmin parallelism – laser grade on every unit; the wedge keeps the rear ghost away from the beam.
  • Rear-face engraving on all ten – the basis of a maintenance record, since the ten optics are otherwise indistinguishable.
  • Deliberate near-infrared limitation – below 2 µm the coating is degraded by design, so a visible alignment beam should not be used to judge it.

Technical Specifications

Parameter Specification
Pack size 10 mirrors
Optic PF20-03-M02, identical to the single-unit version
Coating Mid-infrared enhanced gold with dielectric overcoat
Band 2 – 20 µm
Average reflectance 98 percent
Below 2 µm Performance intentionally reduced; use a different coating
Substrate Fused silica, CTE 0.55 x 10-6 per degree C
Diameter and tolerance 50.8 mm (2 in), +0.0 / -0.1 mm
Thickness and tolerance 12.0 mm (0.47 in), plus or minus 0.2 mm
Clear aperture 45.7 mm, 90 percent of diameter
Surface flatness lambda/10 peak-to-valley at 633 nm
Surface quality 40-20 scratch-dig
Parallelism 3 arcmin or better
Angle of incidence 0 to 45 degrees
Marking Part number laser engraved on the back of each optic

Damage limits for this coating

Condition Value Practical reading
10.6 µm, 100 ns, 1 Hz, spot 1.29 mm 3 J/cm² About 39 mJ on that spot
10.6 µm, CW, spot 1.18 mm 450 W/cm About 53 W on that spot
1.064 µm, 10 ns, 10 Hz, spot 1.06 mm 0.1 J/cm² About 0.9 mJ, low because the coating is not designed here
1.07 µm, CW, spot 1.04 mm 25 W/cm About 2.6 W, the near-infrared penalty in numbers

Two of those four rows describe a coating being used where it should not be. They are included because a production head sometimes carries a pilot or alignment laser near 1 µm alongside the CO2 beam, and the 25 W/cm figure is the reason that pilot beam must not share the final turning mirror. A 2.6 W limit is reached quickly.

Applications

CO2 cutting, marking and drilling heads

Final turning mirrors, gantry folds and focusing-head optics all see the same environment: vapour, spatter and moisture. Holding a pack means the head can be serviced during a scheduled stop rather than after a quality excursion.

Multi-head production cells

A cell with four heads and three mirrors per head has twelve coated surfaces in service. One pack covers the initial fill and the first round of replacements, which is normally enough to get through a commissioning period without an urgent order.

Job shops running mixed materials

Cutting acrylic, coated steel and wood on the same machine exposes the optics to three different contamination chemistries. Organic vapour from plastics is the worst of the three for a mirror, because it polymerises into a film that is hard to remove without mechanical action. A stocked spare lets a contaminated optic be pulled and cleaned properly instead of being wiped in place.

Where the pack is a poor purchase

In a sealed, purged, filtered laboratory enclosure where the optic is never touched, one mirror lasts years and ten is inventory that ages on a shelf. The pack is for environments that consume optics, not for clean rooms that preserve them.

Selection Guide

Contamination sources to design against

Source What it does to the coating Mitigation
Organic vapour from plastics and coatings Polymerises into a translucent film under the beam Extraction at the kerf, positive pressure in the head
Metal spatter and dust Bonds to the surface and scatters; cannot be dissolved off Shield gas across the optic, keep the mirror off the plume axis
Condensed moisture Dries to mineral residue, worst at cold-start Purge the head, allow warm-up before full power
Handling Skin oil and glove residue absorb at 10.6 µm Edge handling only, gloves, no face contact

Three signals that say replace or clean

  1. Process quality drift. A cut that used to be clean needs more power, or the kerf widens, or the marking contrast falls. This is the earliest signal and the one most often attributed to the laser instead of the optics.
  2. Power at the workpiece. A meter reading taken at the nozzle, compared with a recorded baseline, tells you the cumulative loss of the whole delivery path. It does not tell you which mirror is responsible, which is why the next step exists.
  3. Visual inspection under oblique light. A haze, a rainbow sheen or a matte patch inside the clear aperture. Inspect with the head cold and the optic removed; a torch at an angle shows film that looks invisible in normal light.

Allocating a pack across machines

Cell configuration Mirrors in service Pack allocation (worked example)
One head, two folds 3 3 installed, 7 held as service stock
Two heads, three mirrors each 6 6 installed, 4 service stock, order a second pack before the third swap
Three heads, three mirrors each 9 9 installed, 1 service stock, second pack immediately
Four heads, three mirrors each 12 Two packs: 12 installed, 8 service stock

The allocation is arithmetic, not a recommendation about replacement frequency. How fast a given line consumes optics depends on the material, the extraction, the duty cycle and the operator, and only the plant’s own records can answer it.

Series Comparison

Seven coatings on one substrate: 50.8 mm diameter, 12.0 mm fused silica, lambda/10 figure, 40-20 cosmetic grade. For a CO2 line the relevant columns are the thermal-infrared reflectance and whether the surface can be cleaned.

Coating Band Ravg Cleanable Fit for a production CO2 head
-F01 UV enhanced aluminum 250 – 450 nm 90 percent Yes No, wrong band
-G01 protected aluminum 450 nm – 20 µm 90 / 95 percent Yes Possible, but three points lower at 10.6 µm
-P01 protected silver 450 nm – 20 µm 97 / 95 percent Yes No, silver tarnish risk in a dirty head
-M01 protected gold 800 nm – 20 µm 96 percent Yes Workable, and the safer choice if a pilot laser shares the path
-M02 MIR enhanced gold 2 – 20 µm 98 percent Yes Best throughput, provided nothing near 1 µm touches it
-M03 unprotected gold 800 nm – 20 µm 97 percent No No, a dirty head would destroy it
-L01 line optimised gold 10.6 µm line 99 percent No Only in a sealed head that never needs cleaning

FAQ

The mirror has a milky film on it. Can it be cleaned off?

Sometimes, and it is worth one careful attempt before scrapping. Polymerised organic film is the case that responds: soak a lens tissue in reagent-grade acetone, methanol or isopropanol, lay it on the surface for a few seconds, then drag once from the centre outward without pressure. Check the coating handling notes before the first attempt. If the film does not lift in one or two passes, it has usually cross-linked into the coating and further work will only scratch it. Metal spatter never comes off, and neither does anything that has left a visible pit.

How often should the mirrors be replaced?

No catalogue can answer that, because it depends on extraction quality, material mix and duty cycle. The workable method is to record a baseline power at the nozzle on a new optic, re-measure monthly, and set a replacement threshold in your own process capability terms, for example a five percent loss against baseline. Then let the records set the interval. Plants that skip the baseline end up replacing optics on suspicion, which is expensive in both directions.

Why not just use the cheaper protected aluminum coating?

It is three points lower at 10.6 µm and it is a legitimate choice for a low-power marking head. Above roughly a hundred watts at the workpiece, three points per surface across three or four surfaces becomes a real fraction of the delivered power, and the coating cost is small compared with the laser’s operating cost. Do the multiplication for your own path before deciding.

Is the 10-piece pack the same optic as the single-unit M02?

Yes, identical in substrate, coating, figure, cosmetic grade and marking. The difference is quantity, packaging and single-lot grouping.

Can a visible alignment laser be used with these mirrors?

It can be used for bore-sighting, but its brightness tells you nothing about the coating, because performance below 2 µm is deliberately degraded. Do not judge optic health by how bright a red dot looks. Use a power meter at the workpiece, or inspect the surface directly.

Does the pack have a shelf life?

The coating does not degrade in storage if the optic is kept in its case, coated face up, in a dry place. What does degrade is the record: an unlabelled mirror in a drawer after two years cannot be matched to a lot. Keep the pack together, label the case with the lot and the date received, and inspect an optic before it goes into a head after long storage.

Usage Precautions

  • Never wipe a CO2 optic dry. Dry tissue on a contaminated surface grinds the contamination into the coating. Solvent and a single drag, or leave it alone.
  • No alcohol swabs, no household solvents, no abrasive pads. Reagent-grade acetone, methanol or isopropanol with lens tissue only, and check the handling notes first.
  • Do not clean an optic that is still warm. Solvent flashes off unevenly and can leave a residue ring that is harder to remove than the original film.
  • Handle by the edge with gloves, and never touch the clear aperture. Skin oil absorbs at 10.6 µm far more than it does in the visible.
  • Store in the original case, coated face up, never stacked. Ten optics in one box will scratch each other if they are allowed to touch.
  • Keep a written record per position. Optic serial or lot, position, install date, removal date, reason. This is the only way the replacement interval becomes knowable.
  • Do not mix M02 and M01 in the same head without labelling. They look the same and behave differently below 2 µm, which is exactly where a pilot beam lives.
  • Confirm the clear aperture against beam walk. 45.7 mm is generous, but a gantry head moves the beam, and an optic clipped at the edge will heat unevenly and fail early.
  • Enclose and interlock. 10.6 µm is invisible and the two percent that is not reflected still has to go somewhere safe.

Disclaimer

Specifications are the manufacturer’s published values for PF20-03-M02 and apply to every optic in the pack. Average reflectance is a band average from 2 to 20 µm. Damage thresholds are measured on clean optics under the stated conditions and are not a guarantee of survival in a production head, where contamination typically reduces the real limit. Cleaning recommendations reflect the manufacturer’s handling guidance and general practice; they are not a warranty that a contaminated optic can be recovered. Energy and power conversions are our arithmetic from published fluence and spot size. Replacement intervals, allocation examples and contamination descriptions are engineering commentary, not specifications. Gaofei Laser is a distributor of this optic.

Contact Us

Tell us how many heads and mirrors are in service, the material mix and the power at the workpiece, and we will help you size the stock holding and confirm whether the mid-infrared enhanced coating suits the whole path or whether a pilot laser forces the protected gold coating instead.

Hotline: +86 159-2722-0467
Email: 859818709@qq.com
Website: www.soar-laser.cn

Reviews

There are no reviews yet.

Be the first to review “Thorlabs PF20-03-M02-10 Ø50.8 mm (2 in) Mid-Infrared Enhanced Gold Mirror, 10-Piece Pack”

Your email address will not be published. Required fields are marked *

中文EN