QQ: 859818709

Thorlabs PF20-03-M02 Ø50.8 mm (2 in) Mid-Infrared Enhanced Gold Mirror, 2 – 20 µm

Thorlabs PF20-03-M02 Ø50.8 mm (2 in) Mid-Infrared Enhanced Gold Mirror, 2 – 20 µm

Price on request
Category:

Description

Product Overview

PF20-03-M02 is a 50.8 mm (2 in) mid-infrared enhanced gold mirror, 12.0 mm thick on fused silica, specified from 2 to 20 µm with an average reflectance of 98 percent. It is the highest-reflectance metallic coating in this family across the thermal infrared, and it achieves that by accepting a deliberate penalty on the other side of 2 µm. Understanding that penalty is the whole of the selection decision, because the optic is either exactly right for a beam or clearly wrong for it, with very little middle ground.

Two micrometres is a watershed, not a marketing boundary

Gold reflects through a free-electron response, and in the thermal infrared that response is close to ideal: a clean gold surface approaches the theoretical reflectance limit of a good conductor, which is why gold is the default mirror material for CO2 lasers and Fourier transform spectrometers. Below about 2 µm the picture changes. Interband transitions begin to absorb, the reflectance of bare gold sags, and a plain gold coating that is excellent at 10 µm becomes merely adequate at 1.5 µm and poor at 1 µm.

The mid-infrared enhanced coating addresses this with a dielectric multilayer over the gold. The stack is tuned to reinforce reflection in the 2 to 20 µm window, pushing the average from the mid-nineties to 98 percent. The tuning is not free and it is not broadband in both directions: a stack that is resonant above 2 µm is anti-resonant below it, and the manufacturer says so without hedging.

The manufacturer’s own statement of the trade

Thorlabs writes that while the overcoat applied to the mid-infrared enhanced gold mirrors improves performance past 2 µm, it causes performance to suffer in the near-infrared spectral region, and that applications requiring performance below 2 µm should consider another metallic coating or a dielectric mirror. That sentence is the most useful line in the datasheet. It tells you that this is not a general-purpose gold mirror with a bonus, and that a system with a 1 µm pump sharing the same fold as a 10 µm probe cannot be served by one coating.

Why 10.6 µm is its home ground

At the CO2 line the coating is doing what it was designed to do: 98 percent average reflectance, a pulsed damage threshold of 3 J/cm² at 100 ns, and a CW limit of 450 W/cm. Add the fact that gold has very low absorption at 10.6 µm and that fused silica at 12 mm thickness conducts heat well enough to spread a local hot spot, and the combination is a mirror that survives a real industrial CO2 beam rather than only a laboratory one. The same properties serve quantum cascade lasers, globar sources in FTIR instruments, and thermal imaging relays, none of which care about anything below 2 µm.

Key Features

  • 98 percent average reflectance from 2 to 20 µm – the highest of the metallic coatings in this family across the thermal infrared, achieved with a tuned dielectric overcoat on gold.
  • Explicit near-infrared penalty – the manufacturer states that performance below 2 µm suffers; treat 2 µm as a hard design boundary rather than a soft edge.
  • Pulsed threshold 3 J/cm² at 10.6 µm – measured at 100 ns and 1 Hz on a 1.29 mm spot, which is about 39 mJ of energy on that spot.
  • CW threshold 450 W/cm at 10.6 µm – on the 1.18 mm test spot this is roughly 53 W of total power, enough for a production CO2 delivery path.
  • Fused silica substrate, 12.0 mm thick – CTE 0.55 x 10-6 per degree C, with enough thermal mass that a 2 inch aperture does not distort under a few tens of watts.
  • Lambda/10 peak-to-valley at 633 nm and 40-20 scratch-dig – the figure is verified at the helium-neon line, which is a convenient interferometric wavelength rather than an indication of the working band.
  • Clear aperture 45.7 mm, diameter tolerance +0.0 / -0.1 mm – 90 percent of the 50.8 mm outside diameter, standard 2 inch mounting.
  • Thickness tolerance plus or minus 0.2 mm, parallelism 3 arcmin or better – the wedge keeps the rear-surface ghost out of the beam path.
  • Angle of incidence 0 to 45 degrees – the coating is specified as an average, so a 45 degree fold will show the usual s and p separation.
  • Rear-face laser marking – essential here, because a mid-infrared enhanced coating and a plain protected gold coating look identical in visible light.

Technical Specifications

Parameter Specification
Coating Mid-infrared enhanced gold with dielectric overcoat
Specified band 2 – 20 µm
Average reflectance 98 percent
Behaviour below 2 µm Deliberately compromised by the overcoat; use another coating
Substrate Fused silica, CTE 0.55 x 10-6 per degree C
Diameter 50.8 mm (2 in), tolerance +0.0 / -0.1 mm
Thickness 12.0 mm (0.47 in), tolerance plus or minus 0.2 mm
Clear aperture 45.7 mm, 90 percent of diameter
Surface flatness lambda/10 peak-to-valley at 633 nm
Surface quality 40-20 scratch-dig
Parallelism 3 arcmin or better
Angle of incidence 0 to 45 degrees
Marking Part number laser engraved on the rear face

Damage thresholds and the thirty-fold gap

Condition Threshold Energy or power on the test spot
1.064 µm, 10 ns, 10 Hz, spot 1.06 mm 0.1 J/cm² about 0.9 mJ per pulse
10.6 µm, 100 ns, 1 Hz, spot 1.29 mm 3 J/cm² about 39 mJ per pulse
1.07 µm, CW, spot 1.04 mm 25 W/cm about 2.6 W of total power
10.6 µm, CW, spot 1.18 mm 450 W/cm about 53 W of total power

The fluence ratio between 0.1 J/cm² and 3 J/cm² is exactly thirty. The reasons are worth unpacking, because they are not all about the coating. The pulse duration at 10.6 µm is ten times longer, which for a coating with finite thermal diffusion actually helps rather than hurts because the energy spreads during the pulse. The spot is 1.29 mm against 1.06 mm, a 22 percent larger diameter and 48 percent larger area. And gold itself absorbs far less at 10.6 µm than it does at 1.06 µm, where the overcoat and the metal both contribute. Converted to pulse energy the gap widens to roughly forty-four times, because fluence and area multiply.

The 25 W/cm figure at 1.07 µm deserves a separate comment, because it looks alarming and is often misread. Multiplied by the 1.04 mm test spot it corresponds to only about 2.6 W. That is a genuinely low limit and it is real: this coating is absorbing strongly in the near infrared, and a 1.07 µm beam does not belong on it. The number is not a verdict on the product. It is the arithmetic consequence of putting a thermal-infrared coating in front of a near-infrared laser, which is precisely what the manufacturer tells you not to do.

Applications

CO2 laser beam delivery and processing heads

10.6 µm sits in the middle of the design band, where reflectance is highest and absorption is lowest. Beam delivery folds, focusing-head turning mirrors and gantry optics all benefit, and the 12 mm substrate gives enough thermal inertia for a few tens of watts of continuous power.

Quantum cascade laser and thermal source instrumentation

QCLs at 4 to 12 µm, globar sources in FTIR spectrometers and thermal imagers all need a mirror that is equally good across a wide mid-infrared band without a dielectric resonance to fall off. A flat 98 percent average is the property that matters, not a peak value at one line.

Optical parametric oscillator idler arms

When the idler is the beam you care about and it sits between 2.5 and 5 µm, this coating reflects it better than plain gold. The pump arm, however, must be routed with a different coating, because the pump is near 1 µm and this is the worst place in the spectrum for it.

Where this mirror must not be used

Any path that carries 1.06 µm, 1.3 µm, 1.5 µm or a visible alignment beam. That includes most fibre laser systems, most Nd:YAG benches, and almost every laboratory that uses a helium-neon laser for alignment. A visible beam on this coating is not merely dim, it is a sign that the coating is being used outside its design intent.

Selection Guide

Start from the shortest wavelength in the path. That single number decides the coating in almost every case.

  • Shortest wavelength above 2 µm – this optic. Nothing else in the family reaches 98 percent in the thermal infrared.
  • Shortest wavelength between 800 nm and 2 µm – protected gold PF20-03-M01, at 96 percent across the whole 800 nm to 20 µm band.
  • Shortest wavelength between 450 nm and 800 nm – protected aluminum PF20-03-G01 or protected silver PF20-03-P01, both of which cover the visible.
  • Shortest wavelength below 450 nm – UV enhanced aluminum PF20-03-F01.
  • Polarization must be preserved above 2 µm – unprotected gold PF20-03-M03, accepting a surface that cannot be cleaned.
  • One CO2 line only – the line optimised unprotected gold PF20-03-L01, at 99 percent at 10.6 µm.

If the path genuinely carries both a near-infrared pump and a mid-infrared probe, the answer is not a compromise coating; it is two coatings and a dichroic or a flip mount. Trying to force one metal coating to serve both ends of a two-octave span is how throughput budgets fail.

Series Comparison

The same 50.8 mm, 12.0 mm fused silica substrate carries all seven coatings. The table below is arranged by performance on either side of the 2 µm boundary, because that is the axis that decides this family’s use.

Coating Near 1 µm 2 – 20 µm Verdict for a mixed path
-F01 UV enhanced aluminum Not specified Not specified Ultraviolet only
-G01 protected aluminum 90 percent 95 percent above 2 µm The compromise option, lower peak but no cliff
-P01 protected silver 97 percent 95 percent above 2 µm Best visible-to-1-µm option
-M01 protected gold 96 percent average from 800 nm 96 percent The safe all-infrared choice
-M02 MIR enhanced gold Degraded by design 98 percent Do not use below 2 µm
-M03 unprotected gold 97 percent average from 800 nm 97 percent Polarization priority, no cleaning
-L01 line optimised gold Not applicable 99 percent at 10.6 µm Single line only

FAQ

A system has both 1064 nm and 10.6 µm. Should it use M01 or M02?

M01, protected gold, unless the two beams never share a surface. The 1064 nm beam is the constraint: M02 is explicitly degraded below 2 µm, with a near-infrared CW limit of only 25 W/cm and a pulsed limit of 0.1 J/cm², both of which are easy to exceed with a normal pump laser. M01 gives 96 percent across the entire 800 nm to 20 µm span, which is four points lower at 10.6 µm and entirely usable at 1064 nm. If the 10.6 µm arm needs every point of reflectance, give it its own M02 mirrors and combine the beams with a dichroic rather than trying to share a fold.

How much better is 98 percent than 96 percent in practice?

Two points per surface. On a six-surface CO2 delivery path the ratio compounds to about 13 percent more delivered power (0.98 raised to the sixth against 0.96 raised to the sixth), which is meaningful when you are at the edge of a process window. On a single diagnostic pickoff it is invisible. Do the multiplication before paying for the coating.

Is the near-infrared penalty a specification or a warning?

It is a documented qualitative statement, not a number: the manufacturer states that the overcoat improves performance past 2 µm and causes performance to suffer below it, and recommends another coating for work under 2 µm. Treat it as a design rule. The 0.1 J/cm² and 25 W/cm figures at 1.06 and 1.07 µm are the quantitative evidence of how much it suffers.

Can it be cleaned?

Yes, within limits. The overcoat is a dielectric layer and tolerates reagent-grade acetone, methanol or isopropanol applied with lens tissue; confirm against the coating handling notes first. Do not use ethanol-based wipes or dry tissue, and do not scrub. A CO2 processing environment will deposit material on the surface, and periodic cleaning is part of ownership rather than an emergency measure.

Why is the flatness quoted at 633 nm when the mirror works at 10 µm?

Because lambda/10 has to be quoted at a defined wavelength to mean anything, and 633 nm is the standard interferometric line. A surface that is lambda/10 at 633 nm is far better than lambda/10 at 10.6 µm, so the specification is conservative for infrared use. It also means the optic is good enough to align with a visible laser, even though it will not reflect that laser efficiently.

Is 98 percent the best available for 10.6 µm?

Among the metallic coatings in this family, yes. A line-optimised unprotected gold coating reaches 99 percent at 10.6 µm specifically, at the cost of a soft surface that cannot be cleaned and no broadband guarantee. A dielectric coating can go higher still, but it is narrowband and angle sensitive. For a broadband thermal infrared path that must survive handling, 98 percent is the practical ceiling here.

Usage Precautions

  • Never put a near-infrared beam on this optic. The 0.1 J/cm² and 25 W/cm limits at 1.06 and 1.07 µm are low enough that ordinary laboratory pulse energies will exceed them.
  • Clean with reagent-grade acetone, methanol or isopropanol and lens tissue only, after checking the coating handling notes. In a CO2 processing environment, establish a cleaning interval rather than waiting for a visible haze.
  • Handle by the edge, gloved. The dielectric overcoat is harder than bare gold but is still a thin film, and edge damage is where coating failure begins.
  • Keep the beam inside the 45.7 mm clear aperture. The outer 2.5 mm of the diameter is not guaranteed, and in a CO2 head the beam often walks as the gantry moves.
  • Watch the mount, not only the optic. At tens of watts the limiting factor is usually thermal distortion of the holder. Use a mount with a large contact area and avoid point clamping.
  • Do not stack optics and do not store face-down. A 2 inch, 12 mm optic stored on its coated face will need replacing.
  • Identify by the engraved rear marking before installation. This coating and the plain protected gold coating are visually identical; mixing them up produces a system that works at 10.6 µm and fails inexplicably at 1 µm.
  • Enclose the beam. 10.6 µm is invisible, and the two percent that is not reflected is still a hazard.

Disclaimer

Specifications are the manufacturer’s published values for PF20-03-M02. Average reflectance is a band average from 2 to 20 µm and does not describe behaviour at a specific wavelength, angle or polarization. The near-infrared limitation is stated qualitatively by the manufacturer and is not a specified number; the damage thresholds at 1.06 and 1.07 µm are the quantitative indication of it. Damage thresholds are measured on clean optics under the stated conditions and do not guarantee survival in any particular system. Energy and power conversions shown on this page are our arithmetic from the published fluence and spot size, provided to aid interpretation and not as additional specifications. Gaofei Laser is a distributor of this optic.

Contact Us

Tell us the full wavelength set in your path, the pulse duration and the power at the mirror, and we will confirm whether the mid-infrared enhanced coating is appropriate or whether the protected gold coating is the safer choice.

Hotline: +86 159-2722-0467
Email: 859818709@qq.com
Website: www.soar-laser.cn

Reviews

There are no reviews yet.

Be the first to review “Thorlabs PF20-03-M02 Ø50.8 mm (2 in) Mid-Infrared Enhanced Gold Mirror, 2 – 20 µm”

Your email address will not be published. Required fields are marked *

中文EN