Description
Thorlabs PF20-03-P01-10 Ø50.8 mm (2 in) Protected Silver Mirror, 10-Piece Pack
Product Overview
This is the 10-piece pack of the PF20-03-P01; the optic is identical to the single-unit version. Each mirror is a 50.8 mm (2 in) fused silica substrate, 12.0 mm thick, with a protected silver coating: 97 percent average reflectance from 450 nm to 2 µm, 95 percent average from 2 to 20 µm, a silicon dioxide overcoat about 100 nm thick, λ/10 at 633 nm surface figure, 40-20 scratch-dig surface quality, a 45.7 mm clear aperture and a laser-engraved part number on the fine-ground back face.
Silver is the only metal film in common use whose performance declines on its own. Aluminium forms a thin native oxide within minutes of deposition and then stops changing. Gold does not react with anything in a laboratory atmosphere at all. Silver reacts continuously: sulphur compounds in the air convert it to silver sulphide, humidity carries the reaction through pinholes in the overcoat, and the product of that reaction is brown and absorbing. The mirror is not worn out; it is chemically consumed, and it happens whether or not the optic is used.
That single fact changes the procurement logic. A protected aluminium or gold mirror is bought to be used until it is damaged, and one unit is the natural order quantity. A protected silver mirror is bought into a pool, because the question is never “is this mirror good” but “is this mirror still as good as it was”. Answering that question requires a reference, and a reference requires more than one optic.
Ten units is the smallest quantity that supports the practice. It allows a known-good mirror to be held back as a photometric baseline, an in-service population to be rotated through the beamline, and a replacement to be available on the day a station is found to be down two points. It also makes batch records worthwhile, since ten mirrors with the same coating run, the same arrival date and the same measured baseline can be tracked as a group rather than as ten unrelated parts.
Key Features
- Ten units, one specification, one coating batch family. Every mirror in the pack is a PF20-03-P01 with identical optical and mechanical specifications, which is what makes a pool possible: any unit can substitute for any other without re-qualifying the station.
- 97 percent average reflectance from 450 nm to 2 µm, 95 percent from 2 to 20 µm. The highest metallic reflectance available in the visible and near infrared, and still strong in the infrared. This is the performance that the pool is protecting, and the figure against which degradation is measured.
- Silicon dioxide overcoat about 100 nm thick. The layer prevents the silver from oxidising and provides the limited mechanical protection that allows the optic to be mounted and handled with gloves. It is a diffusion barrier, not a seal, which is why the environment still has to be managed.
- Four published laser damage thresholds. 0.225 J/cm² at 800 nm with 99 fs pulses at 1 kHz over a 0.167 mm spot; 1 J/cm² at 1064 nm with 10 ns pulses at 10 Hz over a 1.010 mm spot; 500 W/cm CW at 1.07 µm over a 0.974 mm spot; 1500 W/cm CW at 10.6 µm over a 0.339 mm spot. The pool has to cover both gradual degradation and sudden damage, and the thresholds define the second category.
- λ/10 at 633 nm on a 12.0 mm fused silica body. A thick, thermally stable substrate so that a mirror moved from the store to a mount does not need to be re-characterised for figure; only its reflectance has to be checked.
- Engraved part number on the fine-ground rear face. The engraving identifies the model, not the individual unit, so pair it with your own batch record: arrival date, coating run, initial reflectance, station history. Ten mirrors are few enough that a paper log is sufficient and many enough that a log is necessary.
Technical Specifications
| Item | Detail |
|---|---|
| Part Number | PF20-03-P01-10 |
| Pack size | 10 mirrors |
| Optic in Pack | PF20-03-P01, identical to the single-unit version |
| Coating | Protected silver with silicon dioxide overcoat, about 100 nm |
| Spectral Range | 450 nm to 20 µm |
| Average Reflectance | 97% (450 nm-2 µm); 95% (2-20 µm) |
| Diameter | 50.8 mm (2 in), +0.0 / -0.1 mm |
| Thickness | 12.0 mm (0.47 in), ±0.2 mm |
| Substrate | Fused silica, CTE 0.55 × 10⁻⁶/°C |
| Surface Flatness | λ/10 at 633 nm, peak to valley |
| Surface Quality | 40-20 scratch-dig |
| Clear Aperture | 90% of diameter (45.7 mm) |
| Angle of Incidence | 0° to 45° |
| Rear Surface | Fine ground, part number laser-engraved |
| Pulsed Threshold, Femtosecond | 0.225 J/cm² at 800 nm, 99 fs, 1 kHz, Ø0.167 mm |
| Pulsed Threshold, Nanosecond | 1 J/cm² at 1064 nm, 10 ns, 10 Hz, Ø1.010 mm |
| CW Threshold, 1.07 µm | 500 W/cm at 1.07 µm, Ø0.974 mm |
| CW Threshold, 10.6 µm | 1500 W/cm at 10.6 µm, Ø0.339 mm |
| Environmental Constraint | Not for use in a high-humidity environment; store desiccated |
| Handling | Latex or similar gloves; do not touch face or edge even with gloves |
| Storage Separation | No contact with sulphur-bearing rubber, foam or cardboard |
The 0.225 J/cm² femtosecond figure deserves a note in a page about lifetime management, because it is the number most often exceeded by accident. With 99 fs pulses at 1 kHz over a 0.167 mm spot, that fluence corresponds to roughly 49 µJ per pulse. A mirror that is specified for the throughput of a millijoule-class amplifier can therefore be damaged by a single mis-steered alignment beam if the spot is tight enough, and the resulting damage is a pit rather than a gradual loss, which is why it is caught by inspection and not by the reflectance log.
Applications
This section is about where a managed pool of silver mirrors is worth the administration, not about where a silver mirror is used. The distinction is the whole point of buying ten.
- Multi-station production benches. Where five or six identical inspection or marking stations run the same visible laser, a common pool with a shared baseline lets a station be swapped out during a shift change rather than after a service visit. The station goes back into production with a mirror of known reflectance, and the removed unit is measured later.
- OEM builds with a defined replacement interval. A machine builder who ships a silver-mirror-based optical path can hold ten units to cover warranty replacements across an installed base, with the batch record establishing what “as new” looked like for each shipment.
- Research benches running long experiments. A six-month measurement campaign cannot afford a mid-run change in delivered power. Holding a pool allows a mid-run swap of a suspect fold, with the removed unit kept for post-run comparison so that any drift can be attributed after the fact.
- Facilities with a humid season. In a laboratory where ambient humidity rises predictably for part of the year, silver mirrors degrade on a schedule. A pool converts that into a planned rotation rather than an annual emergency purchase.
- Comparison against alternative coatings. Ten identical silver mirrors make it practical to run a controlled comparison against aluminium or gold over the same period in the same environment, with enough units to separate coating behaviour from unit-to-unit variation.
- Teaching and training laboratories. Where optics are handled by people who are learning, the attrition rate is high and the cause is usually contact rather than laser damage. A pool with a written retirement rule keeps the optical quality of the teaching bench from drifting downward as damaged units are quietly left in place.
Selection Guide
Set the pool size from the number of stations, then set the rotation rule, then set the retirement rule. The order matters: a pool without a retirement rule becomes a drawer of mirrors of unknown quality.
- Count in-service positions. One mirror per fold in active use. A five-station bench with two folds per station is ten positions, which is one pack and no spare margin, so the realistic configuration is two packs or one pack plus a reduced fold count.
- Hold spares at about thirty percent of the in-service count. One spare for every three or four installed mirrors covers both the gradual failures and the handling accidents without tying up capital in optics that sit unused for years. Below twenty percent, a single bad week empties the shelf.
- Reserve one unit permanently as a reference. This mirror never goes into a beamline. It is measured at intervals and used as the comparison standard for every other unit, which removes lamp drift and detector drift from the comparison.
- Rotate on a calendar, not on failure. Move a mirror out of a critical station on a fixed interval and into a non-critical one, so that degradation is caught in a position where it does no harm. This is the practice that distinguishes a managed pool from a stock of parts.
- Confirm the diameter before ordering. The family offers Ø1/2 in (12.7 mm), Ø1 in (25.4 mm) and Ø2 in (50.8 mm) round mirrors and no Ø7 mm size. The two-inch part on this page has a 45.7 mm clear aperture; if the beam is small, the one-inch size is the cheaper way to build a pool of the same depth.
Series Comparison
Because this page is about managing a population of optics rather than choosing one, the comparison below is written as decisions rather than as a specification table.
| If the priority is | Choose | Reflectance | Consequence for a managed pool |
|---|---|---|---|
| Maximum reflectance from 450 nm to 2 µm | P01, protected silver | 97% / 95% | Best performance, and the only coating that requires a retirement rule |
| Zero maintenance and no environment control | G01, protected aluminium | 90% / 95% | Lower reflectance, but a population that does not degrade with time |
| Infrared work above 800 nm with cleanability | M01, protected gold | 96% | Chemically inert, so the pool is limited by handling rather than by time |
| Maximum reflectance above 2 µm | M02, MIR enhanced gold | 98% | Same management model as M01, no time-based degradation |
| No overcoat in the beam path at all | M03, unprotected gold | 97% | Consumable by design; the pool is replenished rather than rotated |
The distinction that matters for a pool manager is in the last column. Silver is the only coating here whose performance is a function of elapsed time and storage conditions; the others are functions of handling and laser exposure. That is why silver is the only one that justifies a reference mirror, a periodic reflectance check and a written retirement threshold, and why buying it ten at a time is the sensible unit.
FAQ
Q1. Will a silver mirror degrade on the shelf by itself if I do not use it?
Yes, slowly, and that is exactly why the pack is managed rather than stored. Silver sulphidation is a chemical reaction with sulphur compounds present in ordinary air, and humidity accelerates it. The 100 nm silicon dioxide overcoat slows the reaction but does not stop it, and Thorlabs is explicit that the mirror must not be used in a high-humidity environment. A mirror kept in a dry cabinet in its case will outlast one kept in a humid drawer by a wide margin, but no storage condition makes a silver mirror immortal.
Q2. How do I know when a mirror should be retired?
Three signals, any one of which is sufficient. First, a measured reflectance more than two points below the baseline established when the unit entered service. Second, a visible change in the coating: a pale yellow cast or a milky haze across the surface, which is the early stage of sulphidation. Third, dark spots at the edge, where the overcoat is thinnest and where attack usually begins. The first signal is the reliable one, and it is only available if a baseline was recorded at the start.
Q3. What should the baseline measurement look like?
A relative measurement is enough: compare the unit under test against the reserved reference mirror at the working wavelength, with the same beam, the same detector and the same angle. Record the ratio, not the absolute reflectance, because the absolute number depends on the reference standard used and the ratio does not. Repeat the comparison at the same intervals, and always in the same order, so that a change in the ratio means a change in the mirror rather than a change in the bench.
Q4. How dry does the storage cabinet need to be?
The manufacturer does not publish a numerical humidity limit for storage; it states the requirement, which is that the mirror must not be used in a high-humidity environment. In practice, use a desiccated cabinet with a hygrometer and keep it as dry as the cabinet will hold, replenish the desiccant when the indicator changes, and never store optics in a sealed box that was closed while the air was humid. The failure mode to avoid is condensation, which happens when a cold optic is brought into a warm room and opened before it has equilibrated.
Q5. Can I keep the silver mirrors in the same drawer as rubber or foam?
No. Vulcanised rubber, many foams, some adhesives and much cardboard release sulphur compounds, and sulphur is precisely what converts silver to silver sulphide. Storing a protected silver mirror in contact with, or even in the same small enclosure as, those materials puts the reactant next to the thing it attacks. Keep silver optics in their original cases, in a cabinet with no rubber gaskets or foam padding nearby.
Q6. Is the ten-piece pack a different product from the single unit?
No. The optic is the PF20-03-P01: 50.8 mm diameter, 12.0 mm thick, protected silver with an overcoat about 100 nm thick, 97 percent average from 450 nm to 2 µm and 95 percent from 2 to 20 µm, λ/10 at 633 nm, 40-20 surface quality, and the same published damage thresholds including 0.225 J/cm² at 800 nm with 99 fs pulses and 1500 W/cm CW at 10.6 µm. Only the quantity and the packaging differ.
Usage Precautions
A pool is only as good as the record that accompanies it. The precautions below are as much about documentation as about handling.
- Record the baseline on arrival. Measure each unit against a reference before it goes anywhere near a beamline, write the date and the ratio on the case, and keep the sheet with the box. Without this step the two-point retirement rule has nothing to compare against and the pool degenerates into a drawer.
- Keep humidity out, and keep the cabinet honest. Desiccated storage, desiccant replenished on the indicator, no sealed boxes closed on humid air, and no cold optic opened before it reaches room temperature. Thorlabs states the mirror must not be used in a high-humidity environment, and storage is the half of that requirement you control completely.
- Separate silver from sulphur sources. No rubber gaskets, no foam padding, no cardboard in the same enclosure. If the original case has foam, keep it as supplied and do not add other materials to the box.
- Gloves on, and still no contact. Latex or similar gloves are recommended, and the recommendation comes with the qualification that even with gloves the coated face and the edge should not be touched. Handle the 2.5 mm rim, and put the optic into its mount before doing anything else with that hand.
- Retire on measurement, not on appearance. Visible change is a late signal. A mirror that looks perfect can be two points down, and a mirror that is two points down will quietly bias every photometric result taken through it.
- Never stack the units. Ten mirrors in one box is ten chances to set one down on another. Store them in the supplied cases, on edge, and never face-down on any surface.
- Do not mix retired and in-service units in the same box. The single most common failure of pool management is a drawer that contains both, with no marking to tell them apart. Retired units leave the laboratory or go into a clearly labelled bin.
Disclaimer
Specifications on this page are compiled from Thorlabs’ publicly available product documentation and are provided for selection reference only. Where this page and the manufacturer’s current official datasheet differ, the official datasheet governs. Coating specifications, damage thresholds and pack quantities may be revised by the manufacturer without notice. Damage thresholds are measured values under the stated test conditions and are not a performance guarantee for any specific application; users are responsible for verifying suitability at their own wavelength, pulse duration, repetition rate, spot size and environment. Reflectance values are averages over the stated bands. Recommended management practices on this page are guidance, not a manufacturer specification. Prices and delivery times are quoted separately.
Contact Us
If you are setting up a managed pool of silver mirrors and want help with pack quantity, baseline measurement or a replacement schedule, please get in touch.
Hotline: +86 159-2722-0467
E-mail: 859818709@qq.com | Website: www.soar-laser.cn
We can supply the ten-piece pack and the single-unit PF20-03-P01, advise on desiccated storage and mounting hardware, and quote protected aluminium or gold alternatives for positions where humidity makes silver impractical.









Reviews
There are no reviews yet.