QQ: 859818709

Thorlabs PF85B-P5 Clamping Fork for Ø1.85 in Pedestal Bases, 0.85 in Slot, 5-Piece Pack

Thorlabs PF85B-P5 Clamping Fork for Ø1.85 in Pedestal Bases, 0.85 in Slot, 5-Piece Pack

Price on request
Category:

Description

Product Overview

PF85B-P5 is a pack of five PF85B clamping forks. Every fork in the pack is the 0.85 in (21.6 mm) counterbored slot version for Ø1.85 in (47.0 mm) pedestal bases, in stainless steel, taking a 1/4 in-20 or M6 cap screw. The pack is not a mixed assortment and it is not a kit: it is five identical parts, which is exactly what a bench usually needs once the number of pedestal bases is counted. The single-unit version carries the part number PF85B; this page is the five-piece pack, PF85B-P5.

The reason a pack exists at all is arithmetic rather than marketing. A laser source, two folds, a focusing stage and a detector is five mounting positions, and each of those positions needs its own base, its own post and its own fork. Nobody builds a bench with one clamped pedestal base. The typical enquiry for a single fork comes from someone who has already built the bench and discovered that one position is unclamped, which is the least convenient moment to place an order.

The engineering reason to buy five rather than one is that forks are hardware, and hardware leaves. A fork goes out attached to a base that is shipped to a collaborator. It disappears into a shared tool drawer. It gets borrowed for a quick rig and never comes back. Its thread picks up a burr after one careless cross-threading and it is quietly retired. It is the first thing that goes into a pocket when a student project is wound down. None of these failures is dramatic, and all of them happen on the afternoon before a deadline.

What each fork does mechanically is worth restating for anyone buying a pack without having used one. These clamping forks create three points of contact with the table. The underside is relieved so the metal bears on three small areas around the base flange instead of a continuous ring. Three points define a plane without over-constraining it, so the base does not rock on a table that is flat to a few micrometres but not perfectly flat, and the assembly repeats its position after being loosened and re-tightened. Once the screw is loosened the fork also swivels through 360 degrees around the pedestal post or post holder, so the clamp can be aimed at whichever tapped hole is closest rather than the base being placed to suit the fork.

The intended companion is the PB4(/M) or PB4R(/M) pedestal base adapter, a solid 303 stainless flange 1.85 in (47.0 mm) across with a 1/4 in-20 or M6 threaded stud, screwed onto the bottom of a Ø1.5 in post. PB4R adds four strong magnets underneath, which is the version to choose when bases are moved often or when one person is doing the assembly alone. A Ø1 in post holder or a BLP01 adjustable-height post can also be clamped directly, in which case the adapter is unnecessary because the holder already presents the flange.

Key Features

  • Five identical forks, one part number. All five are 0.85 in (21.6 mm) slot versions for Ø1.85 in bases. No mixed lengths, so a drawer cannot silently acquire the wrong bar.
  • Three points of contact with the table. A relieved underside produces three bearing areas, which gives high stability, prevents rocking and makes the clamp force predictable.
  • 0.85 in (21.6 mm) counterbored slot. The compact tier of the three fork lengths, for dense layouts where a longer bar will not physically fit.
  • Stainless steel body. Holds the slot geometry through hundreds of tighten-and-loosen cycles and does not shed soft coating debris at the contact points.
  • 360 degree swivel when loosened. Position the base, then rotate the fork to the nearest free tapped hole, then tighten.
  • 1/4 in-20 and M6 screw interface. One fork covers imperial and metric tables, so a pack is not tied to one thread standard.
  • Sized for Ø1.85 in (47.0 mm) flanges. Matches PB4(/M) and PB4R(/M) rather than a nominal 1.85 in footprint that might be a different shape.
  • Stocking quantity, not a discount bundle. Five is the number a five-position bench needs at a 1.3 spare ratio, which is the rule this page works through below.
  • Held in stock. A pack can ship without the two-week build window that applies to made-to-order optics.

Technical Specifications

Parameter Specification
Model PF85B-P5
Pack contents 5 clamping forks, all identical
Component type Clamping fork for pedestal bases
Base compatibility Ø1.85 in (47.0 mm) pedestal bases
Recommended base adapter PB4(/M) or PB4R(/M), 303 stainless, 1.85 in (47.0 mm) OD
Counterbored slot length 0.85 in (21.6 mm)
Slot type Counterbored slot
Cap screw interface 1/4 in-20 or M6
Body material Stainless steel
Contact geometry Three points of contact with the table surface
Rotation 360 degrees around the post or post holder when the screw is loosened
Table compatibility Imperial 1/4 in-20 and metric M6 optical tables and breadboards
Alternative mounting Ø1 in post holder, or BLP01 adjustable-height post, without a base adapter
Quantity per pack 5
Availability Held in stock

The distinction that matters when ordering: PF85B-P5 is five forks, PF85B is one fork. Both are the 0.85 in slot version and both are the same physical part; only the quantity differs. A bench that needs one replacement should order the single unit, and a bench that is being built from scratch should order the pack. Ordering the wrong one is not a technical error, but it is the reason a small project ends up with a drawer full of clamps and a large one ends up short.

Applications

Fitting out a new optical table in one pass. When a bench is assembled for the first time, the mounting hardware is the last thing anyone thinks about and the first thing that stops progress. A pack of five covers the typical five-position layout, and having it on the shelf before the bases arrive removes a week from the build for the sake of a low-cost item.

Standardising hardware across several benches. A laboratory with four benches and a shared store room wants one fork part number, one screw size and one hex key. Packs make that standardisation practical, because the store room can hold whole packs rather than loose parts of uncertain history.

Running parallel builds in a teaching laboratory. In a room where several groups build the same interferometer in the same semester, forks are the part that goes missing. Issuing a pack per station against a station number turns the end-of-term inventory into a counting exercise instead of a procurement exercise.

Keeping a spares drawer that actually has spares. The failure mode for small hardware is not wear, it is absence. A pack held as stock converts a stopped alignment session into a two-minute walk to the drawer, and it costs less than the hour of engineering time it saves.

Multi-position rigs that are rebuilt regularly. Where a rig is re-laid-out between experiments, forks accumulate on the positions that survive and are missing from the positions that get added. Holding a pack means the re-layout is not gated on an order.

Selection Guide

Deciding how many packs to buy is a counting problem, not a judgement call. The method below is the one this page recommends, and it produces a defensible number that survives a budget review.

  • Step 1, count the pedestal positions, not the components. A position is one base plus one post plus one fork. Count the bases on the table, including the ones on the breadboard inserts and the ones on the far end that nobody has mounted yet.
  • Step 2, multiply by 1.3. The 30 percent covers the fork currently on a temporary rig, the one that left with a loaned base, and the one that will be dropped behind the table. It is a spare ratio, not a discount.
  • Step 3, round up to whole packs. Five forks per pack, so the required pack count is the rounded fork count divided by five, rounded up again. The table below does the arithmetic for the common cases.
  • Step 4, check the slot length before committing to the pack. A pack of five is only useful if 0.85 in is the right reach for the bench. If the nearest free tapped hole is routinely more than about 20 mm from the base centre, the 1.25 in or 2.12 in fork is the correct part and a pack of the short version will sit unused.
Pedestal positions on the bench Forks needed at 1.3x Rounded up Order Left over after installation
3 positions 3.9 4 1 pack (5 forks) 2
4 positions 5.2 6 2 packs (10 forks) 6
5 positions 6.5 7 2 packs (10 forks) 5
6 positions 7.8 8 2 packs (10 forks) 4
8 positions 10.4 11 3 packs (15 forks) 7
10 positions 13.0 13 3 packs (15 forks) 5
12 positions 15.6 16 4 packs (20 forks) 8

Two conclusions follow from that table. First, the five-position bench, which is the most common layout, lands on two packs rather than one, because 6.5 rounds to 7 and 7 does not fit in 5. Second, the marginal cost of going from one pack to two is small compared with the cost of a stopped session, so the rounding should always go up rather than down.

Series Comparison

Model Counterbored slot Pack size Best suited to
PF85B 0.85 in (21.6 mm) Single unit One replacement part for an existing bench
PF85B-P5 (this page) 0.85 in (21.6 mm) 5 forks Building or restocking a compact bench
PF125B-P5 1.25 in (31.8 mm) 5 forks General purpose restocking where the middle length is used throughout
PF175B-P5 2.12 in (53.8 mm) 5 forks Large tables where bases are placed by eye and long reach is normal

All four share the stainless body, the three-point contact geometry, the 1/4 in-20 and M6 screw interface and the 360 degree swivel. The only variables are slot length and quantity. That uniformity is the argument for standardising a laboratory on one row of the table: one part number, one screw, one wrench, one tightening habit, and no way for a mixed drawer to produce a base that feels clamped and is not.

A note on the two short-slot rows. PF85B and PF85B-P5 are the same fork, so a bench can start with the pack and top up with single units later without any compatibility question. That is not true of the other two lengths: a 1.25 in fork will not substitute for a 0.85 in fork in a dense layout, and a 0.85 in fork will not reach a hole that a 2.12 in fork was bought for.

FAQ

Q: Is PF85B-P5 five different forks or five of the same?

A: Five of the same. Every fork in the pack is the 0.85 in (21.6 mm) slot version for Ø1.85 in (47.0 mm) pedestal bases. The pack is not a mixed assortment of lengths, so there is no risk of discovering after delivery that only one of the five fits the bench.

Q: What is the difference between PF85B and PF85B-P5?

A: Quantity only. PF85B is one fork, PF85B-P5 is five forks. Both are the same stainless part with the same 0.85 in slot. Buy the single unit for a replacement and the pack for a build or a restock.

Q: How many packs does a typical bench need?

A: Count the pedestal positions and multiply by 1.3, then round up to whole packs. A five-position bench works out at 6.5 forks, which rounds to 7, which means two packs. An eight-position bench works out at 10.4 forks, which rounds to 11, which means three packs. The full table is in the selection section above.

Q: Do the forks need the PB4 or PB4R base adapter?

A: Only if the mount is built on a Ø1.5 in post. PB4(/M) and PB4R(/M) are 303 stainless pedestal base adapters with a 1.85 in (47.0 mm) outside diameter and a 1/4 in-20 or M6 threaded stud, and they are what turn the bottom of a Ø1.5 in post into a flange the fork can clamp. A Ø1 in post holder or a BLP01 adjustable-height post already presents a flange, so no adapter is needed in that case.

Q: Can the five forks be used on different tables with different threads?

A: Yes. Each fork accepts a 1/4 in-20 or an M6 cap screw, and the counterbore is deep enough for either head to sit below the fork surface. The same pack therefore covers an imperial table and a metric breadboard without a second part number.

Q: How much force should be used when tightening?

A: Enough to stop the base moving by hand. Thorlabs warns that significant overtightening of clamping forks can deform the surface of an optical table, which can cause misalignment of components and decrease stability. On a table the dent is permanent, so the correct habit is a short wrench and a light hand, applied consistently by everyone who uses the bench.

Q: Why buy five when one position is currently unclamped?

A: Because the shortage is rarely one part. If a bench has reached the point where one position is unclamped, the spare forks have already gone somewhere: onto a loaned base, into another group drawer, or into retirement after a cross-threaded screw. Buying the pack restores the spare ratio as well as covering the immediate gap.

Usage Precautions

  • Overtightening is the one way to damage something expensive. Thorlabs states that significant overtightening of clamping forks can deform the surface of an optical table, which can cause misalignment of components and decrease stability. The table is the most expensive part on the bench and the deformation cannot be reversed.
  • Keep the five forks together until they are needed. A pack split across three drawers has lost the advantage it was bought for. Label the box with the slot length.
  • Seat the screw head in the counterbore. A head resting on the shoulder instead of dropping into the recess means the slot is not reaching the tapped hole. Change the fork length or move the base rather than forcing the screw.
  • Engage the thread by hand first. Stainless into stainless galls quickly at an angle. Two or three turns by hand before a wrench is applied will prevent most thread damage.
  • Check the flange diameter. These forks are sized for a 1.85 in (47.0 mm) flange. A base with a different diameter will be caught on an edge, and the three-point contact will not be reproduced.
  • Clean with isopropanol and a lint-free wipe. No abrasives, because an abrasive pad rounds the counterbore shoulder and changes the clamp geometry permanently.
  • Do not use a fork as a general-purpose clamp. It is dimensioned for a pedestal base flange. Holding a plate, a filter holder or a custom bracket puts the load where the three-point geometry was never designed to take it.
  • Inspect after any drop. A fork that has fallen onto a hard floor may have one ear out of plane, and it will then clamp at an angle. Replace it; do not straighten it.

Disclaimer

The description and dimensions on this page are compiled from the manufacturer published information for the PF85B fork family and are supplied to help with selection and stock planning. Current official drawings and the spec sheet take precedence over this summary, and the manufacturer may revise specifications without notice. No price appears on this page; price, availability and delivery are confirmed at quotation. The stocking arithmetic in the selection section is a recommendation based on the stated 1.3 spare ratio, not a manufacturer guideline.

Pack quantity is a purchasing convenience, not a specification. The five forks in PF85B-P5 are physically identical to five separately ordered PF85B units, they carry the same slot length and the same material, and they are not matched or serialised as a set. Nothing about the pack changes how a fork behaves on the table, and a pack mixed with single units over the life of a laboratory is entirely normal. The 1.3 spare ratio recommended earlier is a stocking heuristic, not a manufacturer requirement, and a laboratory with its own established ratio should use that instead.

Contact Us

For a quotation on multiple packs, for confirmation that the 0.85 in slot suits an existing layout, or for help matching forks to a base family, contact the sales team with the number of pedestal positions on the bench, the table thread standard and the base model if one is already in use. Quantity breaks on multiple packs and mixed orders that include the PB4 or PB4R adapters are quoted on request.

Packs are held in stock, so an order placed in the morning on a working day is normally released the same day. Mixed orders that combine a pack with the PB4 or PB4R adapters, or with posts and holders, are quoted as a single line so that the whole mount arrives together rather than in two deliveries. Where a bench is being fitted out from scratch, send the intended layout and the sales team will price the complete set rather than the forks alone.

Reviews

There are no reviews yet.

Be the first to review “Thorlabs PF85B-P5 Clamping Fork for Ø1.85 in Pedestal Bases, 0.85 in Slot, 5-Piece Pack”

Your email address will not be published. Required fields are marked *

中文EN