QQ: 859818709

RayTools xStudio Laser Process Programming Platform, CAD, Nesting and Sequencing, DXF PLT G-Code

RayTools xStudio Laser Process Programming Platform, CAD, Nesting and Sequencing, DXF PLT G-Code

Price on request
Category:

Description

Product Overview

A cutting job begins as a drawing, not as a machine command, and xStudio is the place where that drawing becomes something a machine can run. The platform combines CAD drawing, sheet nesting and process sequencing in one environment, so geometry, part arrangement and the parameters that will be applied all exist in the same file before the job is released. DXF, PLT and G-code import cover both the drawings that arrive from customers and the programs that already exist on the shop floor, which means a new job does not require the customer to change how they send work.

The practical difference between xStudio and a drawing tool is what happens after the geometry is finished. Nesting decides how many parts fit on a sheet and where the remnant ends up; sequencing decides the order in which contours are cut and which lead-in each one receives; the parameter set decides what the machine actually does at each contour. In xStudio those three decisions are attached to the part rather than re-entered at the machine, and the version of the parameter set that was used is the version that is sent. That single detail removes the most common cause of a job cutting differently on a second run, which is not a machine fault but a parameter that was retyped by hand.

xStudio is a software platform, licensed by module and by version, and it runs offline: design and nesting continue without a network and synchronise when a connection exists. It does not address hardware directly – making a third-party drive or sensor visible to the control is the job of xNCI in the same ecosystem. The specification table below covers deployment, terminal support, integration, functional modules, file formats, data handling and licence terms rather than machine ratings, because none of those apply to a design environment.

Key Features

  • Drawing and nesting in one window: geometry is created or imported and stays editable until the nest is committed, so a late dimension change does not mean starting the sheet again
  • Automatic nesting with manual override: parts are arranged to raise material utilisation, and any sheet can still be adjusted by hand when the algorithm’s answer does not match the remnant stock actually on the rack
  • Sequencing attached to geometry: cut order, lead-ins, layer assignment and parameter sets are stored with the part instead of being re-entered at the machine terminal
  • Broad import: DXF, PLT and G-code enter the same workflow, which covers both customer drawings and programs that already run in the workshop
  • Parameters travel with the task: the released job carries its parameter set, so the operator receives a sequenced task rather than a drawing that has to be interpreted
  • Design-to-production continuity: one file moves from drawing to nesting to machine task with no manual transcription step in between
  • Offline capable: work continues on a disconnected workstation, and jobs synchronise once the machine network is reachable

Technical Specifications

Brand Empower / RayTools
Model xStudio
Product type CAD, nesting and process programming software platform
Ecosystem xEOS platform
Deployment Local installation on an engineering workstation or industrial PC; offline operation supported, synchronisation when connected
Terminal support Engineering workstation for drawing, nesting and sequencing; machine terminal receives the generated task
Integration target xEOS control systems for direct task handover; other controls through exported program files
Functional modules CAD drawing and editing, sheet nesting, process sequencing, parameter library, task generation
File formats DXF, PLT and G-code import; native project file for the job as a whole
Data capability Parameter library by material and thickness, job archive, task handover to the control
Licence model By module and by version, per workstation; can be bundled with a control system
Hardware specification Not applicable – software product, licensed separately from the machine it prepares work for

Applications

xStudio is used where several drawings have to become a sequence of machine tasks in a day, and where the person doing the nesting is not the person standing at the machine. The pattern is the same across job shops, captive fabrication departments and OEM build lines: drawings arrive in mixed formats, sheets have to be filled properly, and the operator needs a job that is already decided.

  • Job shops running mixed batches, where the nest changes several times per shift and material utilisation decides the margin
  • Production departments that receive DXF drawings from several customers and need one intake route for all of them
  • Fabricators that already hold PLT or G-code programs and want them to enter the same sequencing workflow instead of being run from a USB stick
  • OEM build lines where the process engineer releases a task and the operator only loads, aligns and starts
  • Workshops building a parameter library by material and thickness, so that a known material cuts the same way next month

The work usually starts with a single representative drawing and a single sheet: import, nest, sequence, cut, and compare the result against what the shop does today. That trial answers the two questions that matter before a wider rollout, which are whether the import path is clean for your drawings and whether the nesting gain is real on your remnant stock.

Selection Guide

  • Start from the drawing source: if most work arrives as DXF, the import path is direct. If it arrives as PDF or a photograph of a print, the geometry has to be redrawn or converted elsewhere, and that cost belongs in the decision
  • Size the licence by workstation, not by machine. Design and nesting happen at a desk; the machine only receives the task
  • Decide early who owns the parameter library. One owner with controlled edits is worth more than any feature on this page, because a library with three unofficial copies produces three different cuts
  • If the machines are xEOS-controlled, tasks hand over directly and the workflow is short. On other controls the task is exported as a program file, which works but adds a transfer step
  • Where hardware integration is also in scope – third-party drives, sensors – that is a separate xNCI licence. xStudio does not make hardware visible to the control
  • Plan the trial on a real job with a real remnant, not on a demonstration sheet. Utilisation numbers from a clean full sheet do not survive contact with a half-used plate

Series Comparison

The xEOS suite divides plant work by the question each module answers, and the split between process design and hardware integration is the one users most often ask about.

Module Layer Question it answers Main user
xStudio Process programming What is being cut, in what order, with which parameters Process engineer
xNCI Hardware integration What is this machine built from, and how does the control reach it System integrator
xERP Order and work order What has to be made, by whom, and how far along is it Production planning
xMES Shop floor execution What actually happened at the machine, and can it be evidenced Workshop supervisor
xSmart AI agent Assistance How do I operate, diagnose or document this Operator, service

In one sentence: xStudio decides what the machine should do, xNCI decides what the machine can talk to. A shop that only designs and nests needs xStudio alone; a machine builder assembling a non-standard platform needs xNCI, and usually wants xStudio as well because a machine without a process file is only half delivered. Neither module includes the other, and neither is a substitute for the control system that actually executes the job.

Usage Precautions

  • Check imported geometry before nesting: duplicate entities and open contours are the usual reason a nest looks correct and the cut does not follow it. A contour that is not closed will not produce a usable path, and the fault surfaces at the machine rather than at the desk
  • Keep one owner for the parameter library. Local copies edited by individual operators are how two machines end up cutting the same material differently, and the difference is invisible until a customer measures the part
  • Back up job files and the parameter library before any version upgrade. They are project data held outside the installer, and reinstalling the software does not restore them
  • Confirm the target control version before releasing tasks from a newer release. A task written by a newer version is not guaranteed to be accepted by an older control
  • Licensing is per workstation. Sharing one licence across a network drive is not supported, and the failure appears at the moment a job has to be released, which is the worst possible time
  • Nesting is an aid, not a guarantee. Check the remnant and the cut order on the first sheet of a new job before the rest of the batch is released, because a bad sequence costs a sheet, not a part

FAQ

Is a separate licence required?
Yes. xStudio is licensed by module and by version, per workstation, and it can be bundled with a control system when both are bought together. It is not included with a cutting head or with the machine control.

How good is the nesting?
Automatic nesting plus manual adjustment. The gain depends on part mix and on how much remnant you are willing to reuse; a shop that insists on full sheets will see a different number from one that works down to small offcuts. That is why we trial on your own job rather than quoting a percentage.

Can it be used offline?
Yes. Drawing, nesting and sequencing all run locally. A connection is needed only when tasks are synchronised to the machine network.

Which file formats are supported?
DXF, PLT and G-code for import. Formats outside that set are converted before import, and the conversion is a real step in the workflow rather than something to assume.

Does it control the machine directly?
No. xStudio produces the task; execution belongs to the control system. Making third-party hardware visible to that control is xNCI, a separate module with its own licence.

About the Brand

RayTools, trading as Empower, builds laser cutting heads, welding systems and the xEOS software suite that connects them. The suite is organised by plant function rather than by machine model: process programming, hardware integration, order management, shop floor execution and AI assistance are separate modules with separate licences. This page covers xStudio only; the other modules are documented on their own pages, and none of them is included here.

Disclaimer

Specifications on this page are compiled from the manufacturer’s published material and from existing documentation, and are provided as a selection reference. The delivered product is defined by the current manufacturer specification and by the licence terms issued with it; software behaviour also depends on the control system version that receives the tasks. Features and file format support may change between releases, so confirm the details with us before ordering. Reproduction of this page without written permission is not permitted.

Selection enquiries: Changsha Soar Laser Equipment Co., Ltd., hotline +86 159 2722 0467, www.soar-laser.cn, email 859818709@qq.com.

Reviews

There are no reviews yet.

Be the first to review “RayTools xStudio Laser Process Programming Platform, CAD, Nesting and Sequencing, DXF PLT G-Code”

Your email address will not be published. Required fields are marked *

中文EN