🔷 DOE (Diffractive Optical Element) focused spot size calculator
DOE focused spot size calculator
A DOE (Diffractive Optical Element, such as a beam splitter / dot-array mirror or a homogenizer) splits a single laser beam into a regular dot array or pattern. After the focusing lens, each diffraction order forms a diffraction-limited spot. This tool calculates, after the DOE, thesingle focused spotdiameter, for the selection of dot-array machining, laser drilling and parallel processing.
▦ DOE focused single-spot size calculator
Select the input beam profile, enter the wavelength, focal length, beam aperture and beam quality, and the single-spot diameter of each diffraction order is calculated automatically
μm
Common values: 1064nm=1.064 | 532nm=0.532 | 355nm=0.355
mm
Effective focal length of the focusing lens (f-theta lens) after the DOE
mm
For Gaussian mode, measured at the 1/e² aperture; it should be slightly smaller than the DOE clear aperture (allow a 10~20% margin)
Ideal fundamental mode (TEM₀₀) = 1; real beams are usually > 1
Formula details
The DOE determines the number of split beams and the diffraction angles; a single spot is a diffraction-limited size, depending only on the wavelength, focal length, input aperture and beam profile
Parameter details
How three key inputs determine the DOE single-spot size
Wavelength λ
- In μm: 1064nm=1.064, 532nm=0.532, 355nm=0.355
- The single-spot diameter is proportional to the wavelength: halve the wavelength, halve the spot
- Green 532nm gives a spot half the size of infrared 1064nm, so green/UV is often used for micro-hole machining
- UV 355nm cold processing gives the smallest spot and the lowest heat-affected zone
Input aperture D and fill margin
- D is the beam diameter incident on the DOE (1/e² for Gaussian)
- The spot is inversely proportional to the aperture: the larger D, the smaller the single spot
- D should be slightly smaller than the DOE clear aperture; a 10~20% margin is recommended
- Example: for a DOE aperture of 10mm, take an input D of 8~9mm to avoid edge diffraction / clipping
- Underfilling the beam (D too small) reduces the effective aperture and enlarges the spot
Beam profile and M²
- Gaussian: intense centre, weak edges; use 4M²λf/(πD)
- Flat-top (Top-hat): shaped by a homogenizer; use 2.44M²λf/D
- M²=1 for the ideal fundamental mode; single-mode solid-state ≈1.1, multimode fibre 1.3~5+
- M² scales the diameter linearly and the area quadratically
- When the profile and M² are uncertain, estimate using the worst case (flat-top + measured M²)
📋 Gaussian single-spot diameter quick-reference table
Conditions: Gaussian beam, D = 10mm, M² = 1, in μm (1/e² diameter)
| Wavelength λ \ focal length f | f = 50mm | f = 100mm | f = 160mm |
|---|---|---|---|
| 355nm (0.355μm, UV) | 2.26 μm | 4.52 μm | 7.23 μm |
| 532nm (0.532μm, green) | 3.39 μm | 6.77 μm | 10.84 μm |
| 1064nm (1.064μm, infrared) | 6.77 μm | 13.55 μm | 21.68 μm |
Note: the table gives diffraction-limited values. Actual spot = table value × M²; for flat-top beams use the 2.44 coefficient instead (about 1.92 times the table value). When changing the aperture D, convert inversely by 10/D.
⚠️ Common misconceptions and cautions
Common mistakes in DOE dot-array spot calculation
Should DOE spots be calculated by geometric focusing?
No. The single spot of each DOE diffraction order is adiffraction-limitedsize, determined by wave optics (related to λ, f and D) and cannot be understood as geometric rays “converging to a point”. Geometrical optics predicts a zero-size spot, ignoring diffraction.
More split beams and larger angles mean a larger single spot?
No. The number of split beams (such as 3×3 or 10×10) and the diffraction angles are determined by the DOE’s microstructure period (grating equation) and only change thenumber and spacingof the dot array; every order shares the same focusing-lens F/#, so the diffraction-limited spot size is identical.
Should the 2.44 coefficient also be applied to Gaussian beams?
No. 2.44 is the first-dark-ring coefficient for a uniformly illuminated circular aperture (flat-top) Airy disc; the Gaussian 1/e² diameter must use the 4/π≈1.273 coefficient. Mixing them up overestimates the Gaussian spot by nearly a factor of two, leading to incorrect selection.
The beam need not fill the DOE aperture?
If the incident light covers only a small central area of the DOE, the effective aperture D shrinks, the spot grows inversely, and order efficiency / uniformity degrades. The beam should nearly fill the clear aperture while retaining a 10~20% safety margin to prevent clipping.
Does M² only affect beam thickness?
M² scales the focused spot diameterlinearly: d = M²·d₀. At M²=2 the spot diameter doubles, the area quadruples and the power density falls to 1/4. For multimode lasers the measured M² must be used; do not estimate it as 1.
Is a DOE just an ordinary focusing lens?
No. A DOE is a phase diffractive element that splits one beam into a dot array / pattern (beam splitter) or homogenises it (homogenizer); it does not image the spot itself. Itmust be followed by a focusing lens (f-theta lens)to form the dot-array spots. The two have different roles.


