QQ: 859818709

DOE Spot Size Calculator

DOE Spot Size Calculator

🔷 DOE (Diffractive Optical Element) focused spot size calculator

DOE focused spot size calculator

A DOE (Diffractive Optical Element, such as a beam splitter / dot-array mirror or a homogenizer) splits a single laser beam into a regular dot array or pattern. After the focusing lens, each diffraction order forms a diffraction-limited spot. This tool calculates, after the DOE, thesingle focused spotdiameter, for the selection of dot-array machining, laser drilling and parallel processing.

▦
Gaussian beam (1/e² diameter)
d = 4M²λf / (πD)
Gaussian mode
Top-hat beam (Airy disc dark ring)
d = 2.44M²λf / D
Top-hat (flat-top / uniform) mode
Equivalent f-number
F/# = f / D
The single-spot size depends only on the wavelength λ, focal length f, input aperture D, beam profile and M²

▦ DOE focused single-spot size calculator

Select the input beam profile, enter the wavelength, focal length, beam aperture and beam quality, and the single-spot diameter of each diffraction order is calculated automatically



μm

Common values: 1064nm=1.064 | 532nm=0.532 | 355nm=0.355


mm

Effective focal length of the focusing lens (f-theta lens) after the DOE


mm

For Gaussian mode, measured at the 1/e² aperture; it should be slightly smaller than the DOE clear aperture (allow a 10~20% margin)

Ideal fundamental mode (TEM₀₀) = 1; real beams are usually > 1


📊 Calculation results (single diffraction order spot)
⭕ Single-spot diameter d
—
μm
📏 Single-spot radius r = d/2
—
μm
🔭 Equivalent f-number F/#
—
f/D
📐 Diameter definition (formula form)
—
—

Formula details

The DOE determines the number of split beams and the diffraction angles; a single spot is a diffraction-limited size, depending only on the wavelength, focal length, input aperture and beam profile

① The role of the DOE: turning one beam into a dot array
1 input beam → N×N diffraction orders
A DOE is a phase element with micro- and nano-scale periodic structures etched on its surface. A beam splitter (dot-array mirror) divides the laser into multiple diffraction orders of equal intensity according to the grating equation, forming a regular dot array; a homogenizer redistributes the light into a uniform pattern. After each order passes through the same focusing lens, it forms at the focal planea diffraction-limited spot, which is exactly the single spot this tool calculates.
② Gaussian beam: 1/e² spot diameter
dGaussian = 4·M²·λ·f / (π·D)
λ: wavelength (converted to mm for calculation, λmm = λμm/1000);f: focal length of the focusing lens (mm);D: input beam 1/e² diameter (mm). The result is the diameter at which the focal spot intensity falls to 1/e² of the centre (about 13.5%) — the most commonly used spot diameter definition in laser processing.
③ Flat-top / uniform beam: first dark ring of the Airy disc
dFlat-top = 2.44·M²·λ·f / D
Uniform illumination across the aperture (Top-hat) produces an Airy disc upon circular-aperture diffraction; 2.44 is the diameter multiple of the first-dark-ring angular radius coefficient 1.22. Use this formula when a homogenizer or beam shaper produces a near flat-top profile; the diameter refers to the spot enclosed by the first dark ring.
④ Relationship between the two profiles
dGaussian/dFlat-top = 4/(π·2.44) ≈ 0.521
For the same λ, f and D, the Gaussian spot defined at 1/e² is about 0.52 times the Airy disc diameter. Note that this does not mean Gaussian light is “smaller and better”; rather, the twodiameter definitions differ(1/e² intensity point vs first dark ring), so the aperture definition must be kept consistent when comparing spots.
⑤ Effect of beam quality M²
d = M² · ddiffraction limit
M² (M-squared, the beam quality factor) scales the spot diameterlinearly: M²=1 is the ideal fundamental-mode diffraction limit; multimode fibre lasers often have M² of 1.3~5 or even higher. At M²=1.5 the single-spot diameter is simply multiplied by 1.5. Always use the measured M² for selection; do not assume 1.
⑥ Relationship with F/#
F/# = f/D, and d increases linearly with F/#
Both formulas can be written as d = k·M²·λ·F/# (Gaussian k=4/π≈1.273, flat-top k=2.44). The shorter the focal length and the larger the beam aperture (the smaller the F/#), the smaller the single spot and the higher the power density. In a DOE dot array every order shares the same F/#, soall single spots have the same size。

Parameter details

How three key inputs determine the DOE single-spot size

🌈

Wavelength λ

  • In μm: 1064nm=1.064, 532nm=0.532, 355nm=0.355
  • The single-spot diameter is proportional to the wavelength: halve the wavelength, halve the spot
  • Green 532nm gives a spot half the size of infrared 1064nm, so green/UV is often used for micro-hole machining
  • UV 355nm cold processing gives the smallest spot and the lowest heat-affected zone
⭕

Input aperture D and fill margin

  • D is the beam diameter incident on the DOE (1/e² for Gaussian)
  • The spot is inversely proportional to the aperture: the larger D, the smaller the single spot
  • D should be slightly smaller than the DOE clear aperture; a 10~20% margin is recommended
  • Example: for a DOE aperture of 10mm, take an input D of 8~9mm to avoid edge diffraction / clipping
  • Underfilling the beam (D too small) reduces the effective aperture and enlarges the spot
▦

Beam profile and M²

  • Gaussian: intense centre, weak edges; use 4M²λf/(πD)
  • Flat-top (Top-hat): shaped by a homogenizer; use 2.44M²λf/D
  • M²=1 for the ideal fundamental mode; single-mode solid-state ≈1.1, multimode fibre 1.3~5+
  • M² scales the diameter linearly and the area quadratically
  • When the profile and M² are uncertain, estimate using the worst case (flat-top + measured M²)

📋 Gaussian single-spot diameter quick-reference table

Conditions: Gaussian beam, D = 10mm, M² = 1, in μm (1/e² diameter)

Wavelength λ \ focal length f f = 50mm f = 100mm f = 160mm
355nm (0.355μm, UV) 2.26 μm 4.52 μm 7.23 μm
532nm (0.532μm, green) 3.39 μm 6.77 μm 10.84 μm
1064nm (1.064μm, infrared) 6.77 μm 13.55 μm 21.68 μm

Note: the table gives diffraction-limited values. Actual spot = table value × M²; for flat-top beams use the 2.44 coefficient instead (about 1.92 times the table value). When changing the aperture D, convert inversely by 10/D.

⚠️ Common misconceptions and cautions

Common mistakes in DOE dot-array spot calculation

Should DOE spots be calculated by geometric focusing?

No. The single spot of each DOE diffraction order is adiffraction-limitedsize, determined by wave optics (related to λ, f and D) and cannot be understood as geometric rays “converging to a point”. Geometrical optics predicts a zero-size spot, ignoring diffraction.

More split beams and larger angles mean a larger single spot?

No. The number of split beams (such as 3×3 or 10×10) and the diffraction angles are determined by the DOE’s microstructure period (grating equation) and only change thenumber and spacingof the dot array; every order shares the same focusing-lens F/#, so the diffraction-limited spot size is identical.

Should the 2.44 coefficient also be applied to Gaussian beams?

No. 2.44 is the first-dark-ring coefficient for a uniformly illuminated circular aperture (flat-top) Airy disc; the Gaussian 1/e² diameter must use the 4/π≈1.273 coefficient. Mixing them up overestimates the Gaussian spot by nearly a factor of two, leading to incorrect selection.

The beam need not fill the DOE aperture?

If the incident light covers only a small central area of the DOE, the effective aperture D shrinks, the spot grows inversely, and order efficiency / uniformity degrades. The beam should nearly fill the clear aperture while retaining a 10~20% safety margin to prevent clipping.

Does M² only affect beam thickness?

M² scales the focused spot diameterlinearly: d = M²·d₀. At M²=2 the spot diameter doubles, the area quadruples and the power density falls to 1/4. For multimode lasers the measured M² must be used; do not estimate it as 1.

Is a DOE just an ordinary focusing lens?

No. A DOE is a phase diffractive element that splits one beam into a dot array / pattern (beam splitter) or homogenises it (homogenizer); it does not image the spot itself. Itmust be followed by a focusing lens (f-theta lens)to form the dot-array spots. The two have different roles.

💡 Common application scenarios

⛏️
Laser parallel drilling / cutting dot arrays
A splitting DOE divides a single laser beam into 5×5 or 10×10 dot arrays, drilling dozens of micro-holes in one pulse (fuel injector nozzles, solar cells, PCB micro-vias), multiplying throughput by the number of orders. The single-spot size determines the hole diameter and consistency; use this tool to verify it.
🔬
Structured illumination and parallel imaging
A DOE generates regular dot arrays or grid patterns projected onto the surface of the object under test, for 3D vision, structured-light 3D measurement and light-sheet illumination microscopy. The size of each diffracted spot determines the spatial sampling accuracy and depth of field.
💆
Aesthetic and medical fractional lasers
A fractional DOE splits the treatment beam into hundreds of micro-beams, forming an array of micro-injury zones on the skin for skin resurfacing, scar and stretch-mark treatment. The single-spot diameter and dot spacing directly determine the size of the thermal damage columns and the recovery period.

📋 FAQ

Q: Why are all the spots in a DOE dot array the same size?
Because all diffraction orders pass through the same focusing lens, with identical wavelength, input aperture, F/# and M², the diffraction-limited single-spot size is the same. The DOE only distributes the angle and energy of each order; it does not change the single-spot size. Only if an edge order falls outside the effective field of view of the f-theta lens might it grow slightly due to field curvature / aberration.
Q: The calculation gives 6.77μm, so why is the drilled hole larger in practice?
The calculated value is the 1/e² optical spot; the hole diameter is also affected by heat diffusion, the material ablation threshold, pulse energy and defocus — the region where the energy exceeds the ablation threshold extends beyond the 1/e² boundary. In addition, real M²>1, lens aberration and underfilling all make the actual spot larger. It is advisable to treat this tool’s result as a lower bound and calibrate it with process trials.
Q: Should I choose Gaussian or flat-top?
Direct laser output (single-mode fibre, solid-state fundamental mode) is generally a Gaussian beam — choose Gaussian; if the optical path includes a homogenizer, light pipe or beam-shaping DOE so that the intensity is nearly uniform at the focusing lens, choose Top-hat. Note that the two have different diameter definitions (1/e² vs first dark ring); do not compare the numbers directly.
Q: What is the most effective way to reduce the single-spot size?
The formula suggests three approaches: shorten the focal length f, increase the input aperture D, or use a shorter wavelength λ, plus improving beam quality (lowering M²). However, shortening f reduces the depth of focus and working distance; D is limited by the DOE clear aperture (with a 10~20% margin), and the wavelength is constrained by the laser and material absorption — a trade-off is needed.

中文EN