# Galvo Scanner, F-Theta Lens, and Laser Matching Guide
> Three core rules + one money-saving tip to help you select the right combination without pitfalls
Foreword
In laser marking, engraving, cutting, and other applications, the galvo scanner, the F-Theta lens, and the laser must be correctly matched. Many customers overlook the matching rules during selection, which leads to a reduced work area, insufficient precision, or even equipment damage.
This article summarizes three core matching rules and one money-saving selection tip to help you make the right decision quickly.
1. Spot Size Matching Rule
Core principle
F-Theta lens entrance pupil ≥ galvo beam diameter
Details
The entrance pupil of an F-Theta lens is the maximum beam diameter that can enter the lens. The galvo beam diameter is the diameter of the beam output by the galvo scanner.
| Galvo beam diameter | Required F-Theta entrance pupil | Entrance pupils not recommended |
|---|---|---|
| 7mm | ≥7mm (7mm, 8mm, 10mm) | <7mm |
| 10mm | ≥10mm (10mm, 12mm, 15mm) | 8mm (loses work area) |
| 15mm | ≥15mm (15mm, 20mm) | 10mm, 12mm |
| 20mm | ≥20mm (20mm, 25mm, 30mm) | <20mm |
| 30mm | ≥30mm (30mm and above) | <30mm |
Consequences of a mismatch
Galvo beam diameter > F-Theta entrance pupil → the beam is clipped by the edge of the lens
– Energy loss
– Reduced work area
– Spot distortion
Example: 10mm-beam galvo + 8mm entrance pupil F-Theta lens
– Lens rated: 110×110mm
– Actual marking: may only reach 80×80mm
– Reason: part of the beam is blocked by the edge of the lens
Reverse application tip
F-Theta entrance pupil > galvo beam diameter → can mark a larger area than rated
Example: 10mm-beam galvo + 30mm entrance pupil F-Theta lens (rated 110×110mm)
– Actual marking: up to 200×200mm (provided the galvo deflection angle is large enough)
– Principle: the beam is not clipped at all, so the lens can accept larger deflection angles
2. Scan Angle Matching Rule
Core principle
Galvo deflection angle ≤ scan angle allowed by the F-Theta lens
Details
The rated work area of an F-Theta lens is calculated at its maximum scan angle. If the galvo deflection angle falls short, the actual work area shrinks.
| Scan angle allowed by the F-Theta lens | Galvo deflection angle | Actual work area |
|---|---|---|
| ±15° | ±15° | Reaches the rated work area ✓ |
| ±15° | ±11° | Smaller than the rated work area ✗ |
| ±20° | ±11° | Smaller than the rated work area ✗ |
Consequences of a mismatch
Galvo deflection angle < scan angle allowed by the lens → reduced work area
– The rated work area of the F-Theta lens is calculated at the maximum angle
– If the galvo cannot reach the maximum angle, the work area naturally shrinks
Example: the lens allows ±15°, the galvo can only deflect ±11°
– Lens rated: 110×110mm (calculated at ±15°)
– Actual marking: about 80×80mm (because the galvo only deflects ±11°)
3. Wavelength Matching Rule
Core principle
The wavelengths of the galvo, the F-Theta lens, and the laser must correspond one to one
Details
| Laser type | Wavelength | Galvo wavelength | F-Theta lens wavelength |
|---|---|---|---|
| Fiber laser | 1064nm | 1064nm galvo | 1064nm F-Theta lens |
| UV laser | 355nm | 355nm galvo | 355nm F-Theta lens |
| Green laser | 532nm | 532nm galvo | 532nm F-Theta lens |
| CO2 laser | 10.6μm | 10.6μm galvo | 10.6μm F-Theta lens |
Consequences of a mismatch
Wavelength mismatch → damage to the lens coating
– The optics of both the galvo and the F-Theta lens are coated for specific wavelengths
– A wavelength mismatch lowers the reflectivity
– In severe cases the optics burn out
– Energy loss is severe
Important reminder: wavelength mismatch → damage to the lens coating, which will directly damage the equipment!
4. Money-Saving Tip: Small-Beam Galvo + Large-Entrance-Pupil F-Theta Lens
Principle of the tip
Use a short-focal-length F-Theta lens to achieve a large work area while keeping a small spot and high precision
Details
Conventional approach when a large work area is needed:
– Long-focal-length F-Theta lens → large work area, but a larger spot and lower precision
– High-power laser → high cost
Money-saving approach:
– Short-focal-length F-Theta lens → small spot, high precision
– Large-entrance-pupil F-Theta lens → accepts larger deflection angles
– Small-beam galvo → not clipped, can cover the full angle allowed by the lens
– Result: large work area + high precision + low-power laser
Cost comparison
| Option | Configuration | Advantages | Disadvantages | Cost |
|---|---|---|---|---|
| Option A | High-power laser + long-focal-length F-Theta lens | Large work area | Large spot, low precision, expensive laser | ★★★★★ |
| Option B | Low-power laser + small-beam galvo + large-entrance-pupil F-Theta lens | Small spot, high precision, large work area | Slightly more expensive lens | ★★★☆☆ |
Real case
Requirement: mark 280×280mm with high precision
Option A:
– 50W fiber laser
– F420 F-Theta lens (rated 300×300mm)
– Cost: laser about CNY 8100 + lens about CNY 500 = CNY 8600
– Problem: spot about 77μm, average precision
Option B:
– 30W fiber laser
– 10mm-beam galvo
– F380 F-Theta lens + 200mm entrance pupil (rated 250x250mm, actual marking 280x280mm)
– Cost: laser about CNY 5600 + lens about CNY 1500 = CNY 7100
– Advantage: spot about 65μm, high precision, saving CNY 1500
Conclusion
For a large work area + high precision, a small-beam galvo + large-entrance-pupil F-Theta lens is more cost-effective than a high-power laser!
5. Selection Decision Process
Step 1: Define the application requirements
– Marking area size
– Precision requirement (spot size)
– Material type
– Throughput requirement
Step 2: Choose the laser
– Choose the wavelength by material (1064nm for metal, 355nm for plastic, etc.)
– Choose the power by efficiency and depth requirements
Step 3: Choose the galvo scanner
– The wavelength must match the laser
– Choose the beam diameter by the precision requirement (small beam for high precision)
– The deflection angle must be large enough
Step 4: Choose the F-Theta lens
– The wavelength must match
– Entrance pupil ≥ galvo beam diameter (entrance pupil > beam diameter to exceed the rated area)
– Allowed scan angle ≥ galvo deflection angle
Step 5: Verify the combination
– Check that all three rules are satisfied
– Calculate the actual work area and spot size
– Evaluate the cost of the option
6. FAQ
Q1: Why does my 110×110mm F-Theta lens only mark 80×80mm?
Possible causes:
1. Galvo beam diameter > F-Theta entrance pupil → switch to a lens with a larger entrance pupil
2. Galvo deflection angle < scan angle allowed by the lens → switch to a galvo with a larger deflection angle
Q2: To mark 200×200mm, which configuration is the most economical?
Recommended option:
– Low-power laser (20W) + small-beam galvo (10mm) + large-entrance-pupil F-Theta lens (30mm entrance pupil, F160-F210)
– Saves about 30% compared with directly using a high-power laser + long-focal-length lens
Q3: What happens if the wavelengths of the galvo, the F-Theta lens, and the laser do not match?
– Lower reflectivity → energy loss
– Damage to the lens coating → scrapped equipment
– In severe cases the laser itself can also be damaged
Always keep the wavelengths of all three consistent!
Q4: What if the F-Theta entrance pupil is much larger than the galvo beam diameter?
– Advantage: can mark a larger area than rated
– Disadvantage: the F-Theta lens costs more
– Advice: balance cost and performance according to actual needs
7. Summary
Three core rules
1. Spot matching: F-Theta entrance pupil ≥ galvo beam diameter
2. Angle matching: galvo deflection angle ≤ scan angle allowed by the lens
3. Wavelength matching: the wavelengths of the galvo, the F-Theta lens, and the laser are consistent
One money-saving tip
Small-beam galvo + large-entrance-pupil F-Theta lens = large work area + high precision + savings
Selection advice
– High precision requirement: choose a small-beam galvo
– Large work area requirement: choose a large-entrance-pupil F-Theta lens
– Cost control: prioritize upgrading the F-Theta lens rather than the laser
Disclaimer: This article is a summary based on practical application experience. For specific selection, combine the actual equipment parameters with advice from professional engineers.
*This article was prepared by the technical team of Soar Laser (高飞激光). Feel free to contact us with any questions.*
*Hotline: 15927220467*
*Email: 859818709@qq.com*



Leave a Reply