1064nm Pulsed Q-Switched Fiber Laser Parameters Explained — From Spec Sheet to Real-World Selection
The spec sheet is packed with parameters—which one actually determines processing results? Why do two 100W lasers deliver dramatically different outcomes? This article focuses on the 1064nm pulsed Q-switched fiber laser and explains every parameter in depth: what it is, what the number differences mean, how it affects processing, and how to judge it when selecting. It helps you read the spec sheet and pick the right laser.
Chapter 1: What Is Q-Switching? — Energy Storage → Instant Release
The essence of Q-switching can be summarized in one sentence: store energy first, then release it instantly.
“Q” is the quality factor of the resonant cavity and represents the cavity’s ability to store optical energy. The Q-switching process unfolds in two steps:
- Low-Q state (energy storage): a high-loss element (an acousto-optic Q-switch or a passive saturable absorber) is inserted into the resonant cavity so the cavity cannot build up oscillation; pump energy keeps being stored in the gain medium and population inversion accumulates continuously;
- High-Q state (release): the intracavity loss is lowered in an instant, and the accumulated energy is released as a giant pulse within an extremely short time (on the nanosecond scale).
It is like storing water behind a dam—first close the gate to hold the water (low Q), then open it instantly to release the flood (high Q). Energy accumulated slowly over a whole second pours out within a few nanoseconds; that is the fundamental reason a Q-switched laser’s peak power far exceeds its average power.
How it differs from MOPA: MOPA (master oscillator power amplifier) is another pulsed technology. It generates pulses by directly driving the electrical signal of a semiconductor seed source, with independently adjustable pulse width and repetition rate and high flexibility. This article focuses on Q-switching and does not expand on MOPA. Q-switching’s advantages are a simple structure, low cost, and high single-pulse energy, which give it an irreplaceable position in deep metal engraving, rust removal, and other applications that demand large single-pulse energy.
How it differs from continuous-wave (CW) lasers: a CW laser emits light continuously and its average power equals its instantaneous power; a Q-switched laser may average only a few tens of watts, yet reach peak power of hundreds of kilowatts or even megawatts. As an analogy, CW is like steady flow out of a water pipe, while Q-switching is like a water hammer—one strike delivers an instantaneous impact far beyond the push of the flowing water.
Chapter 2: A Panorama of the Core Q-Switched Laser Parameters
Before looking at the individual parameters, establish the global picture. The core parameters of a Q-switched laser are not isolated; they are tightly coupled through two fundamental formulas:
- Average power = pulse energy × repetition rate (P_avg = E_p × f)
- Peak power = pulse energy ÷ pulse width (P_peak = E_p ÷ τ)
These two formulas show: at constant average power, a higher repetition rate means lower pulse energy; at constant pulse energy, a narrower pulse width means higher peak power. These four parameters (average power, pulse energy, repetition rate, pulse width) form a four-parameter linked system—adjust one and the other three shift. Once you understand this, the parameter explanations that follow all fall into place.
Beyond these four, there are “quality-type” parameters such as beam quality M², beam diameter, wavelength, power stability, divergence angle, and polarization. What they determine is not “whether the beam is strong enough” but “whether the beam is good to use.”
Chapter 3: Wavelength — 1064nm, the Workhorse Wavelength of Industrial Lasers
Why 1064nm?
1064nm is the fundamental output wavelength of ytterbium-doped (Yb³⁺) fiber lasers. In industrial laser processing, 1064nm is the undisputed “workhorse wavelength” for three reasons:
- High fiber transmission efficiency: 1064nm sits right in the low-loss window of silica fiber, so the beam can be delivered flexibly to the processing head through fiber; equipment layouts stay flexible and the optical path is maintenance-free—this is the greatest engineering advantage of 1064nm fiber lasers over solid-state lasers;
- Mature component ecosystem: after more than twenty years of industrialization, the core components in the 1064nm band—pump sources, fibers, isolators, combiners, Q-switches—have mature supply chains, continuously falling costs, and high reliability;
- High value for money: at the same power class, 1064nm fiber lasers cost far less than lasers at other wavelengths, and maintenance is cheaper too—no crystal aging, no frequency-conversion efficiency decay.
Absorption Characteristics of 1064nm Across Materials
Spec sheets never list “material absorptance,” yet it is precisely the underlying logic for judging whether this laser can do your job:
| Material | 1064nm Absorptance | Processing Behavior |
|---|---|---|
| Carbon steel / stainless steel | ~35-40% | Good absorption; excellent marking and deep engraving results |
| Copper | ~5% | Low absorptance; much of the energy is reflected and high peak power is needed to break through |
| Aluminum | ~5-7% | Low absorptance, similar to copper; highly reflective materials need special handling |
| Glass | Nearly transparent | Requires extremely high peak power to trigger nonlinear absorption before it can be processed |
| Ceramics (alumina) | Relatively high | Acceptable absorptance; marking and drilling are feasible |
| Plastics | Mostly transparent | Only plastics containing fillers/pigments can be marked; pure plastics respond poorly |
What does this mean for your selection?
- If you mainly process steel/stainless steel—1064nm is the best choice: high absorptance, good efficiency, low cost; pick it without hesitation;
- If you mainly process highly reflective metals such as copper/aluminum—1064nm still works, but you must choose a model with sufficiently high peak power to break through the reflection barrier instantly; also pay attention to back-reflection protection so reflected light cannot damage the laser source;
- If you mainly process glass/transparent plastics—1064nm is not an ideal choice; unless you have a laser with extremely high peak power (>100kW) to trigger nonlinear absorption, processing efficiency will be very low.
Selection Guidance
- Steel/stainless steel marking and deep engraving → 1064nm is the first choice, best value for money
- Copper/aluminum processing → 1064nm is usable; prefer high-peak-power models
- Ceramics/alumina → 1064nm is feasible; medium power suffices
- Glass/pure plastics → 1064nm processing is limited; assess whether it meets your needs
Chapter 4: Average Power
Definition and Physical Meaning
Average power is the total energy the laser outputs per unit time. The “100W” or “300W” printed on a spec sheet is average power. It is the most easily misunderstood parameter—many assume higher power means stronger processing, but average power is only the “total energy budget”; how much energy each pulse actually receives depends on the repetition rate.
Interpreting the Number Differences
Average power alone does not directly determine processing results; it must be read together with the repetition rate. For example:
- Laser A: 100W average power at 20kHz → pulse energy = 100W ÷ 20kHz = 5mJ
- Laser B: 100W average power at 100kHz → pulse energy = 100W ÷ 100kHz = 1mJ
At the same 100W, A’s pulse energy is 5 times B’s! On the same material, A digs a pit with one strike while B needs five strikes to reach the same depth.
The spec sheet says “100W”—how should you read it? Do not stop at that number—turn to the repetition rate and pulse width parameters and calculate the pulse energy and peak power. Those are what actually determine the processing results.
Impact on Processing
Average power sets the ceiling of overall processing efficiency. Higher power means you can run at higher repetition rates with the same parameter combination, or deliver larger pulse energy at the same rate. But with a poorly matched parameter set (high frequency + narrow pulse width), high power can still end up “a big horse pulling a small cart”—energy gets spread across a large number of low-energy pulses, and none of them is strong enough.
Selection Guidance
- Surface marking/color marking: 20-50W is enough
- Deep metal engraving/cutting: 100-300W
- High-speed large-area processing: 200W and above
Core principle: never judge by the power number alone—combine frequency and pulse width to evaluate pulse energy and peak power.
Chapter 5: Peak Power — The Core Value of Q-Switching
Definition and Physical Meaning
Peak power is the maximum power of a single pulse during the pulse duration. The formula is:
P_peak = E_p ÷ τ
where E_p is the pulse energy and τ is the pulse width (FWHM).
The core reason Q-switched lasers exist is to produce high peak power. A Q-switched laser averaging just 20W can easily reach peak power above 10kW—which is exactly how it “defeats the strong with the weak” and breaks through material within nanoseconds.
Interpreting the Number Differences
Take the real model parameters of Q-switched fiber lasers as examples:
- Raycus RFL-P30QB (30W), 1mJ@100ns → peak power = 1mJ ÷ 100ns ≈ 10kW
- Raycus RFL-P100QA (100W), 1mJ@80ns → peak power = 1mJ ÷ 80ns ≈ 12.5kW
- Max Photonics MFPN-50M-1.1 (51W), 1.1mJ@95ns → peak power = 1.1mJ ÷ 95ns ≈ 11.6kW
- Raycus RFL-P70Q (70W), 1mJ@80ns → peak power = 1mJ ÷ 80ns ≈ 12.5kW (higher at the low-frequency end)
As you can see, the peak power of Q-switched lasers typically sits in the 10-15kW range, and a 100W model’s peak power is not much higher than a 30W model’s—because Q-switching is characterized by high pulse energy but relatively wide pulse widths (80-200ns), so its peak power figures fall short of narrower-pulse technologies (e.g., MOPA’s 2-20ns). But Q-switching’s advantage lies precisely in the large pulse energy itself—each pulse carries more energy and removes more material per pass, which is the core requirement of deep engraving and rust removal.
The spec sheet says “peak power >10kW”—what does that mean for your processing?
- 5kW peak power → can only “skim the surface” of metal (shallow oxidation discoloration); acceptable for shallow marking, not for deep engraving
- 10-20kW peak power → can vaporize metal, one pulse per micro-pit; sufficient for deep metal engraving
- 30-50kW peak power → high deep-engraving efficiency, suited to high-removal processing; stronger penetration into highly reflective metals (copper/aluminum)
Impact on Processing
- High peak power → vaporization-dominated removal → small heat-affected zone → little chipping, few burrs
- Low peak power → melting-dominated removal → large heat-affected zone → more burrs, larger chipping
Typical applications: deep metal engraving, coating stripping, processing of highly reflective metals.
Selection Guidance
- Coating stripping/removal: peak power >10kW suffices
- Deep metal engraving: peak power 15-50kW
- Reflective-metal processing / high-removal work: peak power >30kW
Always check the peak power curve (peak power vs. pulse width) in the spec sheet—do not rely on the peak figure alone, which is usually quoted at a specific pulse width.
Chapter 6: Pulse Energy
Definition and Physical Meaning
Pulse energy is the total energy carried by one pulse, in millijoules (mJ) or microjoules (μJ). It is the bridge between average power and repetition rate:
E_p = P_avg ÷ f
Interpreting the Number Differences
Back to the real-model comparison for Q-switched fiber lasers:
| Model | Brand | Average Power | Pulse Energy | Pulse Width | Peak Power |
|---|---|---|---|---|---|
| Max Photonics MFP-20X | Max Photonics | 18-19W | 0.7mJ | 70-110ns | 6.4-10kW |
| Max Photonics MFP-20L | Max Photonics | 20W | 1mJ | 80-120ns | 8.3-12.5kW |
| Raycus RFL-P30QB | Raycus | 30W | 1mJ | 90-110ns | 9.1-11.1kW |
| Max Photonics MFP-50W | Max Photonics | 50W | 1-1.5mJ | 100-140ns | 7.1-15kW |
| Raycus RFL-P100QA | Raycus | 100W | 1mJ@20-70kHz | 50-110ns | 9.1-20kW |
Within the same 20W class, the Max Photonics MFP-20L’s 1mJ pulse energy is 43% higher than the MFP-20X’s 0.7mJ, and the difference in deep-engraving results is significant. This shows that selection cannot rely on power class alone: at equal power, the pulse-energy gap between models can be larger than the gap across power classes.
Q-switched lasers deliver their highest pulse energy at low repetition rates, and pulse energy falls as the rate rises—this is inherent to Q-switching. Higher-average-power models can maintain higher pulse energy output at high rates, but the maximum pulse energy at low rates is limited by nonlinear effects and the damage threshold in the fiber; doubling power does not double energy.
The spec sheet says “pulse energy 1mJ”—how do you judge whether that is enough? In deep engraving, the material volume removed per pulse is roughly proportional to the pulse energy. A 1mJ laser digs a pit nearly twice as deep as a 0.5mJ one per pulse—not twice as fast, but done in one pass. If your deep-engraving efficiency is insufficient, look at pulse energy first, not at adding power.
Impact on Processing
Pulse energy directly determines the amount removed in a single pass. In deep engraving, the material volume removed per pulse is roughly proportional to the pulse energy. A 1mJ laser digs a pit nearly twice as deep as a 0.5mJ one per pulse—not twice as fast, but done in one pass.
Selection Guidance
- Marking/color marking: 0.1-0.5mJ suffices
- Deep metal engraving: >0.5mJ
- Thick-sheet cutting / high-removal work: >1mJ
Always note the test conditions attached to the “maximum pulse energy” figure (@ how many ns, @ how many kHz)—a number stripped of its conditions is meaningless.
Chapter 7: Pulse Width
Definition and Physical Meaning
Pulse width is the time span, in nanoseconds (ns), over which the laser pulse passes through half its peak (FWHM) from rise to fall. It is one of the most critical parameters of a Q-switched laser and directly determines whether the process runs “hot” or “cold.”
Interpreting the Number Differences
| Pulse Width | Typical Peak Power (1mJ pulse example) | Processing Behavior | Heat-Affected Zone |
|---|---|---|---|
| 80ns | ~12.5 kW | Relatively cold processing; a higher share of material is vaporized | Small (30-80μm) |
| 100ns | ~10 kW | Transition zone between hot and cold processing | Medium (50-100μm) |
| 140ns | ~7.1 kW | Hot processing; melting dominates | Large (80-150μm) |
| 200ns | ~5 kW | Clearly hot processing | Very large (>200μm) |
An 80ns pulse’s peak power is about 2.5 times that of a 200ns pulse—at the same pulse energy, halving the pulse width doubles the peak power. Although the Q-switched pulse-width tuning range (achieved indirectly by adjusting the repetition rate) is narrower than MOPA’s (MOPA spans 2ns to 500ns), within the Q-switched adjustable range (80-200ns) choosing the pulse width wisely still significantly affects the processing results.
Examples of pulse-width differences across real models:
- Raycus RFL-P30QS pulse width 130-160ns (wide-pulse type) vs. Raycus RFL-P30QB pulse width 90-110ns (narrow-pulse type)—both 30W, yet the pulse widths differ greatly. The P30QB has higher peak power and suits fine marking; the P30QS applies heat longer per pulse and suits heat-conduction welding
- Raycus RFL-P100QA pulse width 50-110ns (wide tunable range): as narrow as 50ns at the low-frequency end, back to 110ns at the high-frequency end—the pulse width of the same laser changes automatically with repetition rate, an inherent Q-switching characteristic
- Max Photonics MFPN Nano series uniformly 80-110ns—the Nano2 generation improved pulse-width consistency, with smaller pulse-width fluctuation across the entire frequency range and a more stable process window
Impact on Processing
Pulse width governs the competition between the timescale of energy release and heat diffusion in the material. When the pulse width is far shorter than the material’s thermal relaxation time (typically on the microsecond scale for metals), heat is carried away (by vaporization) before it can spread—this is “cold processing.” When the pulse width approaches or exceeds the thermal relaxation time, heat spreads into the surrounding material and forms melt that resolidifies—this is “hot processing.”
- Shorter pulse widths (80-100ns): relatively small heat-affected zone, lighter chipping; suited to fine marking and shallow engraving
- Wide pulse widths (>100ns): large removal per pulse and fast processing; suited to deep metal engraving and roughing
How the pulse-width choice affects chipping/burrs: take glass drilling as an example—drilling with a wide 200ns pulse can chip the edges beyond 500μm; switching to a shorter 80-100ns pulse keeps chipping within 300μm. This is not fine-tuning; it is a qualitative change.
How large is the chipping on your cuts? Check the pulse width first. Many customers report heavy burrs and large chipping on cut edges, and their first reaction is “not enough power,” when in fact the pulse width is often too wide. What to do? Two paths: first, choose a narrower-pulse model at selection time (for example, the Raycus RFL-P30QB’s 90-110ns suits fine processing better than the P30QS’s 130-160ns); second, reduce the repetition rate appropriately in use—after a Q-switched laser is slowed down, population inversion accumulates more fully, the pulse width narrows automatically and the pulse energy rises, peak power improves through both effects, and chipping improves noticeably.
Selection Guidance
- Ceramics/sapphire: 80-100ns (Q-switched pulse widths are wide; high pulse energy must compensate)
- Precision metal marking: 80-120ns
- Deep metal engraving / rust removal: 100-200ns
- Marking filled plastics: 80-120ns (1064nm has limited effect on pure transparent plastics)
Chapter 8: Repetition Rate
Definition and Physical Meaning
Repetition rate is the number of pulses the laser emits per unit time, in kHz. It is inversely proportional to the pulse energy (at constant average power).
Interpreting the Number Differences
| Repetition Rate Range | Typical Pulse Energy (100W example) | Typical Applications |
|---|---|---|
| 1-10kHz | 10-100mJ | Deep engraving, high-energy drilling |
| 20-80kHz | 1.25-5mJ | Conventional marking, shallow engraving |
| 80-200kHz | 0.5-1.25mJ | High-speed marking, fine marking |
Examples of repetition-rate range differences across real models:
- Raycus RFL-P30QS: 40-60kHz (narrow band) → a limited frequency window, suited to marking tasks within a specific rate range without frequent parameter changes
- Raycus RFL-P100QA: 20-200kHz (wide band) → high frequency flexibility, covering everything from deep engraving to high-speed marking; one machine, multiple processes
- Max Photonics MFP-20W: 20-80kHz → a moderate frequency range that meets conventional marking needs
- Max Photonics MFP-100W: 20-200kHz (wide band) → pulse energy up to 6.7mJ; aggressive material removal for deep engraving at low rates, and marking at high rates too
The cutoff-frequency concept: Q-switched fiber lasers typically run at 1-200kHz and have a cutoff frequency (roughly 80-200kHz, depending on the model); beyond the cutoff frequency the pulse energy drops sharply and peak power collapses. Pulse formation in Q-switching depends on the accumulation of inverted population inside the cavity; when the rate is too high, the population is extracted again before it can fully accumulate, so the pulse energy naturally decays sharply.
Impact on Processing
- High frequency: high spot overlap, fine and uniform background texture, high processing efficiency—but low pulse energy and weak penetration
- Low frequency: large pulse energy and strong penetration—but low spot overlap and coarse background texture
Frequency and processing efficiency: doubling the frequency does not double the efficiency. In deep metal engraving, 5 pulses at low frequency (20kHz) can remove far more material than 25 pulses at high frequency (100kHz)—because at low frequency each pulse carries much higher pulse energy and peak power, and the material is removed by vaporization, far more efficient than the melting-dominated removal at high frequency.
Is your marking efficiency up to par? Do not tweak the frequency alone. Many customers crank up the frequency for speed, only to see the pulse energy plummet and the marks get shallower and shallower. The right approach: first determine the minimum pulse energy required to achieve the desired processing result, then raise the frequency subject to that constraint—that is real efficiency gain.
Practical Case: The Three-Layer Deep-Engraving Method — Deep and Smooth at Once
Many customers’ requirements are contradictory: deep engraving calls for low-frequency, high-energy digging, but low frequency leaves a coarse texture; smoothness calls for high-frequency fine pulses, but high frequency cannot go deep. One frequency cannot solve it—so split the work into layers: different frequencies do different jobs.
Take a 100W Q-switched laser deep-engraving stainless steel as an example. Such lasers typically run at 50-100kHz; set three layers in the marking software and process them in sequence:
Layer 1: roughing layer — low frequency + full power, aggressive material removal
| Parameter | Setting | Rationale |
|---|---|---|
| Frequency | 50kHz | Low-rate end = high pulse energy = deep removal; each pulse digs one deep pit |
| Power | 100% | Full-power output to maximize removal |
| Fill spacing | 0.05-0.08mm | Wider spacing for fast scanning |
| Fill angle | 45° | Diagonal fill to avoid following the grain direction of the material |
| Fill mode | One-way fill | Each line is fired in one direction only, so the return pass does not disturb the previous line |
Result after Layer 1: deep enough, but the texture is very rough—deep pits piled one on top of another, with gullies visible to the naked eye.
Layer 2: transition layer — medium frequency + medium power, leveling peaks and filling valleys
| Parameter | Setting | Rationale |
|---|---|---|
| Frequency | 80kHz | Medium rate = medium pulse energy, moderate removal |
| Power | 60-70% | Full power is unnecessary; avoid over-cutting |
| Fill spacing | 0.03-0.05mm | Denser than Layer 1; refinement begins |
| Fill angle | 135° | Crossed with Layer 1’s 45° to flatten Layer 1’s “peaks” |
| Fill mode | Serpentine fill (bidirectional) | Fires in both directions for efficiency; the transition layer does not need perfect uniformity |
Result after Layer 2: the depth is essentially reached and the texture is clearly improved, but it is still not refined—faint striations remain visible.
Layer 3: finishing layer — high frequency + low power, polishing the base
| Parameter | Setting | Rationale |
|---|---|---|
| Frequency | 100kHz | High-rate end = small pulse energy; each pulse removes only a micro-amount, like polishing |
| Power | 25-40% | Low power prevents over-cutting; surface touch-up only |
| Fill spacing | 0.01-0.02mm | Extremely dense spacing to ensure a uniform, fine texture |
| Fill angle | 0° (or 90°) | Crossed again with the previous two layers to eliminate residual striations |
| Fill mode | Serpentine fill (bidirectional) | Even in both directions, so the final texture is consistent |
Result after Layer 3: deep with a smooth texture—flat and fine to the touch.
Why must the fill angles of the three layers cross? Each layer’s fill direction leaves striations in that direction on the floor. If all three layers run in the same direction, the striations stack and deepen; crossing 45°→135°→0° lets each layer erase the previous layer’s striations, leaving the final floor without obvious directional texture.
The core logic in summary:
- Low frequency does the “digging”—large pulse energy removes material aggressively, with no regard for finish
- Medium frequency does the “leveling”—medium energy flattens peaks and fills valleys, transitioning toward fine work
- High frequency does the “polishing”—small pulse energy removes micro-amounts, like sandpaper
One frequency cannot do all three jobs, but three layers each doing its own deliver far better results than repeatedly marking at a single frequency. This is the practical value you unlock once you truly understand how frequency affects pulse energy and processing results.
Selection Guidance
- Deep engraving/drilling: 1-50kHz
- Conventional marking: 20-80kHz
- High-speed fine marking: 80-200kHz
Chapter 9: Beam Quality M²
Definition and Physical Meaning
M² is the factor that measures how close a laser beam is to the ideal fundamental mode (TEM₀₀, Gaussian distribution). M²=1 means a perfect Gaussian beam; the larger M², the “dirtier” the beam—it contains higher-order mode content and the energy distribution is less concentrated.
Interpreting the Number Differences
The influence of M² on the focused spot and the depth of focus is described precisely by the following formulas:
Focused spot diameter: Φ₀ = 4M²λf / (πΦ)
Depth of focus: DOF = 2πΦ₀² / (M²λ)
With a 1064nm wavelength, an F=160mm F-Theta lens, and a Φ=6mm incident beam:
| M² | Focused Spot Φ₀ | Depth of Focus DOF | Actual Processing Behavior |
|---|---|---|---|
| 1.0 | ~36 μm | ~2.4 mm | Smallest spot and most concentrated energy, but short depth of focus |
| 1.2 | ~43 μm | ~2.9 mm | Excellent industrial grade; high marking precision |
| 1.5 | ~54 μm | ~3.1 mm | Slightly lower precision, larger depth of focus; advantageous for deep engraving |
| 2.0 | ~72 μm | ~3.2 mm | Spot noticeably larger; fine processing limited |
| >3.0 | >108 μm | — | Coarse texture; roughing only |
From M² 1.0 to 1.5, the spot area grows 2.25 times and the energy density falls to 44% of the original—worse than cutting the power in half.
M² comparison of real models:
| Model | Brand | M² | Positioning |
|---|---|---|---|
| Max Photonics MFP-20 | Max Photonics | <1.4 | Best in its class; first choice for precision marking |
| Max Photonics MFP-20X | Max Photonics | 1.1-1.6 | Balances precision and power; compact type |
| Raycus RFL-P30QB | Raycus | <1.5 | Balances precision and deep engraving |
| Max Photonics MFP-50W | Max Photonics | 1.8 | Power-first type; high power came at the cost of beam quality |
| Raycus RFL-P100QB | Raycus | <1.8 | Power-first type at the 100W class |
As you can see, higher-power models tend to have larger M²—high power needs a larger mode-field area to carry the energy, which inevitably introduces some higher-order modes. At the 30W class M² can reach <1.5, while the 50-100W class usually sits at 1.5-1.8; this is the fundamental trade-off between power and beam quality.
The spec sheet says M²<1.5—what does that mean for you? It means the focused spot diameter is around 54μm (paired with an F=160mm F-Theta lens), enough for precision marking and ordinary deep engraving. If your work demands micron-level precision, only M²<1.2 will do; if you only do large-area cleaning, even M²<3 does not matter.
⚠️ When calculating the focused spot and the depth of focus, always use the laser’s actual M²—never casually set it to 1 or 1.1! M²=1 is the ideal Gaussian beam and does not exist in reality; M²=1.1 is reached only by a very few high-end models under laboratory conditions. Many customers enter 1.0 or 1.1 without thinking, get an underestimated depth of focus and spot size that do not match the actual processing results, and then wrongly suspect that something is wrong with the laser.
⚠️ Watch out for understated M² figures. Some manufacturers quote M² values on spec sheets that are too low; the measured values are often larger. How do you judge whether a figure is understated? Use Raycus as the benchmark—Raycus is China’s fiber laser leader whose engineering strength and quality control are industry benchmarks; its 30W class is rated M²<1.5 and its 100W class M²<1.8. If another maker’s rated M² at the same power class is smaller than Raycus’s (say, a 100W model rated M²<1.3), you should raise an eyebrow—if Raycus cannot achieve that number, on what basis can they? Most likely the test conditions are cherry-picked (measured only at specific frequencies and specific power points), or the figure is simply fudged. The safe approach: for unfamiliar brands, estimate the actual M² by adding 0.1-0.2 to Raycus’s same-class figure; the depth of focus and spot size calculated that way will be closer to reality.
Impact on Processing
- M²<1.2: fine marking lines with sharp edges; suited to precision marking and micromachining
- M²<1.5 (e.g., the Raycus pulsed series, the Max Photonics pulsed series, the IPG Q-switched series): balances power and precision; suited to deep metal engraving and versatile processing
- M²>2: large spot and dispersed energy; only suited to large-area cleaning or roughing
The practical meaning of depth of focus: in deep engraving the material surface gradually sinks; if the depth of focus is insufficient, the laser quickly goes “out of focus” and engraving deeper becomes harder and harder. A beam with a slightly larger M² has a longer depth of focus, which actually favors deep engraving—this is the precision-versus-depth trade-off.
Why does your deep engraving stall as it goes deeper? Many customers report: the marking machine engraves fast and deep at first, but after about 2mm it suddenly seems to lose strength—a pass produces almost no visible change in depth—and their first reaction is that the laser’s power has degraded. In fact, calculate the depth of focus first. Use the formulas above, together with your laser’s M² and the focal length of the F-Theta lens, to find the actual depth of focus in mm. Suppose your M²=1.5, the F-Theta lens is f=160mm, and the incident beam diameter is 7mm: the depth of focus comes out at only about 1.8mm. What does that mean? After the laser is focused, only within ±0.9mm of the focal point (1.8mm in total) is the spot small enough and the energy density high enough to vaporize and remove material quickly. By the time you have engraved 1.5mm deep, the laser’s focal point still sits at the original material surface while the pit bottom has moved ever farther from the focal plane—the spot reaching the bottom grows, the energy density plummets, and the material goes from “vaporizing” to “melting” to “barely warmed at the surface,” so naturally it stops engraving. This has nothing to do with laser power; a brand-new laser gives exactly the same result, because it is the physics of optical focusing. There are two solutions: first, switch to a longer-focal-length F-Theta lens (for example, from f=160mm to f=254mm)—the depth of focus grows with the square of the focal length, from 1.8mm to over 4.5mm, directly doubling the deep-engraving capability; second, engrave layer by layer and refocus at each layer, lowering the Z axis manually or automatically every 0.5-1mm so the focal point always follows the pit bottom. It is cumbersome, but it works best.
Selection Guidance
- Precision marking/micromachining: M²<1.2
- General processing/deep engraving: M²<1.5 is acceptable
- Cleaning/large-area processing: M²<3 suffices
Chapter 10: Beam Diameter
Definition and Physical Meaning
Beam diameter is the spot size (1/e²) of the laser as it exits the output head, in mm. It directly affects the matching with the galvo scanner and the beam expander, and the final focusing result.
Interpreting the Number Differences
The beam diameter of Q-switched pulsed fiber lasers typically falls in the 5-9mm range, with about 7mm as the typical value. For example, the Raycus RFL-P100QA is 5.7-8mm, the Max Photonics MFP-50W is 6-9mm, and the Max Photonics MFP-100W~300W models are 5-8mm. Some models support custom beam diameters to customer requirements.
What this beam diameter means:
- Matching with the galvo scanner: a 5-9mm beam diameter directly matches a 10mm-aperture galvo scanner (a 10mm scanner passes beams up to about 10mm), so it can be used directly without a beam expander—the system configuration is simple
- If a smaller focused spot is needed: add a beam expander to fill a larger-aperture scanner (14-15mm), but Q-switched lasers, unlike MOPA, do not offer small-spot/large-spot dual versions; the beam diameter is relatively fixed
Impact on Processing
From the focusing formula Φ₀ = 4M²λf / (πΦ), the larger the beam diameter Φ, the smaller the focused spot Φ₀. Take the typical 7mm beam diameter of a Q-switched laser: focused by an F=160mm F-Theta lens, the spot is about 54μm (at M²=1.5); if a 2X beam expander widens the beam to 14mm before it enters, the focused spot is about 27μm—a 4-fold difference in spot area and a significant energy-density gap.
⚠️ When calculating the depth of focus and the spot size, always use the laser’s actual output beam diameter—do not substitute the scanner aperture! Many customers see that they use a 10mm-aperture scanner and assume the beam entering the F-Theta lens is 10mm—wrong. A 7mm beam passing through a 10mm-aperture scanner comes out still 7mm; it does not automatically become 10mm. The scanner aperture only states “the maximum that can pass,” not “what actually passes.” Calculating the depth of focus and spot size with 10mm yields severely underestimated results and misleads the selection.
⚠️ When adding a beam expander, the matching of the entire optical path must be worked out: laser → beam expander → galvo scanner → F-Theta lens, with each stage’s aperture accommodating the next. A practical example: the laser outputs a 7mm beam; after a 2X beam expander it becomes 14mm—the scanner must be at least a 14mm aperture, preferably 15mm to leave margin (the galvo mirrors sit at 45°, so a 14mm beam requires a mirror physical size of ≥14/cos45°≈19.8mm; only a 15mm-aperture scanner’s mirrors are large enough); the entrance pupil of the F-Theta lens must also exceed 14mm, otherwise the beam is clipped at the lens edge, losing energy and distorting the spot. If any link in the chain has insufficient aperture, the beam expander’s benefit is wasted—or it can even perform worse than without one: the clipped beam produces diffraction rings, making the focused spot larger and dirtier instead.
Are your marking lines not fine enough? It may not be a power problem—the beam diameter may be mismatched. A 7mm beam into a 10mm-aperture scanner achieves only a 49% fill ratio (7²/10²=0.49); more than half of the scanner aperture is wasted, so the focused spot is naturally large. For finer lines, the correct approach: add a 2X beam expander to widen 7mm to 14mm → pair it with a 15mm-aperture scanner → ensure the F-Theta entrance pupil is ≥14mm; only then can the spot drop from 54μm to 27μm and the energy density increases 4-fold.
Selection Guidance
- 10mm-aperture scanner → directly matches the typical 7mm Q-switched beam, but the fill ratio is low
- 15mm-aperture scanner + 2X beam expander (7mm→14mm) → full fill and a smaller focused spot; confirm the F-Theta entrance pupil is ≥14mm
- Work backward from the precision requirement: need a smaller spot → add a beam expander + larger scanner + large-entrance-pupil F-Theta lens, matching the entire optical path stage by stage
Chapter 11: Power Stability
Definition and Physical Meaning
Power stability describes how much the laser’s output power fluctuates over time, usually expressed as a ± percentage, divided into short-term stability (second scale) and long-term stability (8-hour continuous operation).
Interpreting the Number Differences
| Stability Grade | Fluctuation Range | Actual Behavior |
|---|---|---|
| ±1% | 99-101W (100W rated) | Extremely stable; high-end Q-switched class |
| ±3% | 97-103W | Industrially acceptable |
| ±5% | 95-105W | Typical for ordinary Q-switched fiber lasers |
Impact on Processing
Power fluctuation affects processing consistency nonlinearly. Take black marking on stainless steel as an example: a ±3% power fluctuation can make the color uneven, ranging from deep black to light gray; in thin-sheet metal cutting, a ±5% fluctuation can cause failure to cut through and over-cutting to alternate.
Short-term stability affects the uniformity of processing on a single workpiece; long-term stability affects the consistency between the first and the last parts in batch production. For automated production lines, long-term stability matters more than short-term stability.
Poor consistency in your batch processing? Check power stability first. First parts pass while last parts fail—the most likely cause is long-term power drift. A laser rated ±5% may drift from 105W to 95W over 8 hours of operation while the processing parameters are left unchanged—problems are only to be expected.
Selection Guidance
- Precision processing / 3C manufacturing: ±1%~±2%
- Conventional marking: ±3% is acceptable
- Cleaning / roughing: ±5% is acceptable
Chapter 12: Divergence Angle
Definition and Physical Meaning
The divergence angle describes how much the beam spreads due to diffraction during propagation, in mrad (milliradians). The smaller the divergence angle, the more parallel the beam and the better the far-field spot quality.
Interpreting the Number Differences
| Divergence Angle | Spot Growth at 1 Meter | Beam Quality Correlation |
|---|---|---|
| <1 mrad | Growth <1mm | Near the diffraction limit, M²≈1 |
| <2 mrad | Growth <2mm | Excellent industrial grade |
| <5 mrad | Growth <5mm | Typical for ordinary fiber lasers |
Impact on Processing
A beam with large divergence, after passing through the beam expander and the F-Theta lens, yields a larger and less uniform focused spot. In long optical path systems (e.g., where the laser sits far from the scanner), the effect of divergence is especially obvious—a 5mrad beam grows 10mm over a 2m transmission run and may exceed the scanner aperture.
The divergence angle is intrinsically linked to M²: a beam with large M² usually has a large divergence angle too, because higher-order modes diffract at larger angles.
Selection Guidance
- Precision processing / long optical paths: <1.5mrad
- Conventional marking: <2mrad
- Short-path roughing: <5mrad is acceptable
Chapter 13: Polarization
Definition and Physical Meaning
Polarization describes the oscillation direction of the laser’s electric field vector. Light is a transverse wave: the electric field oscillates in the plane perpendicular to the propagation direction, and different oscillation directions mean different polarization states. Do not underestimate this parameter—with different polarization directions, the material absorptance can differ several-fold, and the marking results can differ dramatically.
A Complete Guide to the Polarization Types
1. Linear polarization
The electric field vector oscillates back and forth in one fixed direction, like a shaken rope. Linear polarization has two subclasses, defined relative to the plane of incidence—when the laser hits the material surface, the incident ray and the surface normal define a plane (the plane of incidence):
- P-polarization (Parallel): the electric field oscillates parallel to the plane of incidence. P-polarization has extremely low reflectance at Brewster’s angle → maximum material absorptance; nearly all the energy goes in
- S-polarization (Senkrecht, German for “perpendicular”): the electric field oscillates perpendicular to the plane of incidence. S-polarization always has relatively high reflectance → low material absorptance; a large amount of energy is reflected back
P- and S-polarization are not two independent polarizations; they are two states presented by the same linearly polarized light hitting the material surface, depending on the direction of the plane of incidence. When the polarization direction is parallel to the cut kerf it is P-polarization (good absorption); perpendicular to the kerf it becomes S-polarization (poor absorption).
Pros: high polarization purity and a definite direction; usable in polarization-sensitive precision measurement and interferometry
Cons: pronounced directional differences in marking—lines along the polarization direction are sharp and dark, lines perpendicular to it are fuzzy and light; cutting shows the same directional differences
2. Random polarization
The polarization direction changes randomly from pulse to pulse: this pulse points east, the next may point south, west, or north. Over a large number of pulses, all directions are covered uniformly.
Pros: absorption is uniform in all directions, so marking shows no directional differences—no matter which direction the lines run, the depth is consistent and the color uniform
Cons: the polarization state is uncontrollable; polarization selectivity cannot be exploited for specific processes
3. Circular polarization
The electric field vector does not oscillate back and forth along a line; instead it rotates uniformly around the propagation direction, advancing like a screw thread. A 1/4 wave plate can convert linear polarization into circular polarization.
Pros: similar to random polarization—absorption is uniform in all directions and the marking result is consistent in every direction
Cons: not truly random—circular polarization is a deterministic rotating state; the 1/4 wave plate adds cost and optical-path complexity
How the Three Polarization Types Affect Processing: A Comparison
| Polarization Type | Marking Behavior | Cutting Behavior | Typical Uses |
|---|---|---|---|
| Linear | Large directional differences: lines deep along the polarization direction, shallow perpendicular to it | Large directional differences: good along the polarization direction, poor perpendicular to it | Polarization-sensitive measurement, interferometry |
| Random | Uniform in all directions: consistent depth and uniform color | Uniform in all directions: consistent quality | Metal marking, general processing (Q-switched standard) |
| Circular | Uniform in all directions, consistent results | Uniform in all directions, consistent quality | Conversion when a linearly polarized laser needs improved directionality |
Polarization in Q-Switched Fiber Lasers
Q-switched fiber lasers all use random polarization—the Raycus RFL-P series, the Max Photonics MFP series, and the IPG Q-switched series without exception. This is an inherent feature of Q-switched fiber lasers: the resonant cavity contains no polarization-selective elements, and the birefringence produced by fiber bending and stress naturally randomizes the polarization state.
What does this mean for processing? For marking it is a natural advantage—no need to worry about directionality; whether the lines run horizontally or vertically, the depth is consistent and the color uniform. Both Q-switched and MOPA fiber lasers are randomly polarized, so absorption is uniform in all directions during marking and the directional differences of linear polarization simply do not exist. Only if you use a linearly polarized laser (some solid-state lasers) do you need to pay attention to the effect of polarization direction on processing consistency.
Do your marking lines differ noticeably by direction? If you use a linearly polarized laser (some solid-state lasers), the energy absorption can differ by 30-50% between the polarization direction and the line direction, making the marking shallower in one direction than another. Add a 1/4 wave plate to convert the linear polarization into circular polarization, and the results in all directions may become consistent. Q-switched and MOPA fiber lasers are both randomly polarized—polarization is not the problem there; go check the pulse width and the repetition rate.
Selection Guidance
- Metal marking: the Q-switched random polarization is naturally suited—absorption is uniform in all directions, line depth is consistent, and no extra handling is needed
- Special applications (polarization-sensitive materials): note that Q-switched fiber lasers are all randomly polarized; linearly polarized versions are not available
Chapter 14: How the Parameters Couple — Why You Cannot Look at a Single Parameter
Return to the core formulas:
- P_avg = E_p × f (average power = pulse energy × repetition rate)
- P_peak = E_p ÷ τ (peak power = pulse energy ÷ pulse width)
This means the four parameters (P_avg, E_p, f, τ) have only two degrees of freedom—specify any two and the other two are locked in.
Processing Differences Between Parameter Sets at Equal Power
Using 30W average power as an example, compare the actual parameters of different brands/models:
| Model | Brand | Repetition Rate | Pulse Width | Pulse Energy | Peak Power | Typical Use |
|---|---|---|---|---|---|---|
| Raycus RFL-P30QB | Raycus | 10-30kHz | 90-110ns | 1mJ | ~10kW | Deep metal engraving |
| Max Photonics MFP-30W | Max Photonics | 30kHz | 100-140ns | 1mJ | ~8.3kW | Conventional marking |
| Max Photonics MFPN-30M-1 | Max Photonics | 30kHz | 80-110ns | 1mJ | ~11kW | Fine marking |
All 30W, yet the three lasers differ markedly in processing: the Raycus RFL-P30QB supports operation down to 10kHz and removes a large amount per pulse at low rates, suiting deep engraving; the Max Photonics MFPN-30M-1 has a narrower pulse width and higher peak power, giving finer marking lines and a smaller heat-affected zone on metal; the Max Photonics MFP-30W has a wider pulse width and moderate peak power, suiting conventional marking that does not need extreme parameters. Judging by the “30W” figure alone, you simply cannot tell what this laser is suited for.
Reading the Parameter Curves
The peak power vs. pulse width curve commonly found in spec sheets: the higher the curve the better, but pay more attention to its flatness—flat means the peak power varies little across pulse widths and the process window is wide; steep means high peak power is available only at specific pulse widths and the process window is narrow.
The pulse energy vs. repetition rate curve: the pulse energy is high and stable in the low-frequency band and drops sharply in the high-frequency band—the turning point of the drop is the intuitive manifestation of the “cutoff frequency.” When choosing an operating frequency, try to avoid the high-frequency band near the turning point.
Chapter 15: The Selection Decision Tree — Parameter Priorities by Application
Marking (Metal Surface Marking)
Parameter priority: beam quality M² > pulse-width tunability > frequency range > average power
Recommended range: 20-50W, pulse width 80-140ns, frequency 1-200kHz, M²<1.5
Typical picks: Max Photonics MFP-20L (20W/1mJ pulse energy; engraves deeper than same-power compact models), Max Photonics MFP-20X (20W/0.7mJ/compact size; the preferred choice where space is limited), Raycus RFL-P30QB (30W/1mJ/narrow pulse width; balances fine work and deep engraving), Max Photonics MFP-50W (50W/1-1.5mJ; power-first marking efficiency)
Deep Engraving (Deep Metal Engraving)
Parameter priority: pulse energy > peak power > pulse width > average power
Recommended range: 100-300W, pulse energy >0.5mJ at low frequency (1-50kHz), peak power >50kW, pulse width 80-200ns
Typical picks: Max Photonics MFP-100W (100W/20-200kHz/pulse energy up to 6.7mJ/M²=2; first choice for high-removal roughing—fierce energy but a coarse spot), Max Photonics MFP-70W (70W/50-170kHz/1.4mJ@50kHz/M²=1.8; balances energy and spot quality—the value pick for deep engraving), Raycus RFL-P100QA (100W/20-200kHz/1mJ pulse energy/M²<1.6; general marking and shallow engraving with a fine spot)
The pulse-energy-versus-M² trade-off: among 100W Q-switched lasers, the Max Photonics MFP-100W leads by far with 6.7mJ pulse energy, but at M²=2 its spot is coarse—suited to deep engraving and cleaning where precision does not matter; the Raycus P100QA has a fine spot (M²<1.6) but only 1mJ pulse energy, so it strains at deep engraving. The Max Photonics MFP-70W is the compromise between the two—1.4mJ is 40% higher than Raycus, and M²=1.8 beats the MFP-100W, covering both engraving depth and precision. This is also a fixed rule of Q-switched fiber lasers: the higher the power and the larger the pulse energy, the worse M² inevitably becomes—choose according to whichever constraint bites you harder.
Drilling (Metal/Ceramic Micro-Holes)
Parameter priority: pulse energy > peak power > beam quality > frequency
Recommended range: pulse energy >2mJ, peak power >20kW, M²<1.5, frequency 1-50kHz
Typical picks: Max Photonics MFP-70W (70W/1.4mJ@50kHz/M²=1.8; balances energy and precision—first choice for precision metal drilling), Max Photonics MFP-100W (100W/pulse energy up to 6.7mJ/M²=2; first choice for large-diameter drilling—fierce energy but a coarser spot)
Note: 1064nm Q-switched lasers drill metal excellently; drilling ceramics/sapphire is feasible but requires high pulse energy; for glass drilling, the Q-switched peak power is usually insufficient to trigger nonlinear absorption, so the results are limited
Cutting (Thin Metal Sheet/Film)
Parameter priority: peak power > pulse energy > frequency
Recommended range: 50-200W, peak power >20kW, frequency 20-80kHz
Cleaning / Rust Removal / Coating Stripping
Parameter priority: average power > pulse energy > beam diameter
Recommended range: 100-300W, pulse energy >0.5mJ, frequency 20-80kHz
Typical picks: the Raycus pulsed cleaning series, the Max Photonics pulsed cleaning series
Note: the principle of cleaning/rust removal is not just “burning off” the rust layer; thermal-expansion stripping plays the main role—the rust layer and the substrate have different thermal expansion coefficients, so after pulsed-laser irradiation the two expand unevenly, and huge shear forces at the interface “tear” the rust off rather than fully vaporizing it. Cleaning therefore places low demands on M²: even M²=2 or larger works perfectly well. The keys are pulse energy large enough and peak power high enough to generate sufficient thermal stress.
Surface Oxidation Black Marking
Parameter priority: power stability > frequency range > beam quality
Recommended range: 20-50W, power stability within ±2%, frequency 80-120kHz
Typical pick: Raycus RFL-P30QB (30W/10-30kHz narrow pulse width; stable black marking on stainless steel)
Note: Q-switched fiber lasers can only perform basic oxidation black marking (forming a black Fe₃O₄ oxide layer on the stainless steel surface), controlling the heat input with high frequency + small pulse energy so the surface oxidizes without ablation. Color marking is beyond what Q-switching can do—color marking requires precise control of the pulse width to tune the oxide-film thickness (different thicknesses produce different interference colors), which is MOPA’s strength (2-8ns narrow pulses + high frequency); the Q-switched pulse width cannot be adjusted independently, so it cannot do it. If your customer asks for color marking on stainless steel, recommend a MOPA laser directly—do not force a Q-switched laser to do the job.
Final Thoughts
Reading the spec sheet is only the first step; real selection skill lies in understanding how the parameters couple and how much weight each one carries for a specific process. No parameter is good or bad in isolation—a narrow pulse width is the killer feature in precision marking yet offers no advantage in deep metal engraving; high peak power paired with small pulse energy enables precision processing of brittle materials, but for marking large areas it is actually less efficient than a 50W Q-switched laser.
Selecting a 1064nm pulsed Q-switched fiber laser boils down to answering three questions: What materials do you process? What results do you need? What is your throughput requirement? Answer those three clearly, then compare them against the parameter interpretations in this article, and you will be able to pull the truly useful information out of the pile of spec-sheet numbers and find the laser that fits best.
Selection is, at its core, matching: align the laser’s “capability profile” with the application’s “requirements profile” and pick the model with the largest overlap. May this article help you avoid detours and choose right the first time.
Soar Laser (SOAR-LASER) — Focused on Laser & Optics Solutions
🌐 https://www.soar-laser.cn
📞 159-2722-0467



Leave a Reply