Laser Glass Cutting: Pick the Wrong Method and Chipping Ruins Your Parts!
Three Types of Glass Laser Cutting Machines Explained in One Article
Glass is hard and brittle and chips at the slightest touch. Laser cutting is now the mainstream method, but different solutions are all called “laser glass cutting” yet differ dramatically—edge chipping ranges from 3 microns to 500 microns, speed differs by a factor of 100, and cost ranges from RMB 150000 to 5000000. Choosing wrong wastes money; the bigger trouble is product quality problems.
Today the three mainstream methods are laid out in full—no filler, straight to the conclusions.
1. Why Is Glass So Hard to Cut?
In short: the heat cannot escape. Glass conducts heat poorly, so when the laser strikes, heat piles up locally—at best the edge chips, at worst the panel cracks. The three methods are essentially three different heat-control strategies.
Principle 1: direct ablation. The laser energy vaporizes the glass directly wherever the cut is needed—high precision, but slow.
Principle 2: modification and weakening. The laser writes a “weakening line” inside the glass—it does not burn through; it makes the glass weak, so that an external force or thermal stress then breaks it along the line. Far more efficient, with better edge quality.
Principle 3: thermal stress cleaving. The laser only heats a line; thermal expansion and contraction create stress, and the glass splits open along the line. There is no need to burn through the glass—”cracking it apart” is enough.
Method 1: Bottom-Up Layer-by-Layer Ablation — the First Choice for Drilling
Start with a real-world scenario: how are the camera hole, speaker hole, and various sensor holes in a smartphone cover glass made? The answer is the bottom-up layer-by-layer ablation method.
In the factory, the laser head fires from above the glass; the beam passes through the entire panel and focuses at the bottom, then starts burning from the bottom surface, one layer at a time, moving upward. Once a layer is ablated, the focus steps up a little and the next layer is ablated, until the hole goes all the way through. The whole process may take only a few seconds—no chipping, no taper, vertical hole walls, precise dimensions. That is the core value of the bottom-up method: it takes precision hole drilling to the extreme.
How does it cut?
Ordinary glass absorbs only 3-8% of 1064nm infrared laser light (transmission about 92-97%), which means infrared light passes almost straight through the glass—this is the difficulty of glass cutting, but it is exactly the entry point of the bottom-up method: let the laser enter from above, pass through the whole panel, and focus on the bottom surface. Energy density is highest at the focal point; once it exceeds the ablation threshold of glass (about 2 J/cm²), the glass is vaporized on the spot. And so, starting from the deepest layer, the beam burns upward one layer at a time.
Think of scooping ice cream with a spoon—start at the bottom, scoop away one layer, lift the spoon a little, scoop the next layer, until you dig through the whole cup.
Where does the debris go? Throughout the process, the ablated debris falls naturally downward into the collection tray at the bottom of the machine; it never touches the glass surface, let alone floats up to contaminate the F-Theta lens and galvo scanner above. If the laser fired straight down from above the glass, debris would fly upward and easily stick to the optics—once a lens gets dirty, laser power drops, cutting quality degrades, and frequent cleaning or even replacement is required, which is fatal.
Operator safety. The laser always travels inside the glass and the beam path is enclosed, so operators above face no direct laser exposure and need no extra protective equipment. If the laser fired upward from below, the beam would pass through the glass and exit at the top, putting the operator’s eyes at risk. That is why the bottom-up method is very simple to engineer—the machine configuration is simple, operators are safe, and consumables last longer.
Core equipment: nanosecond MOPA fiber laser
MOPA stands for “Master Oscillator Power Amplifier”. Think of it as a “signal booster”—it first generates a small, precise seed signal, then amplifies it stage by stage along the fiber, and finally outputs a high-power laser.
The defining feature of the MOPA architecture is that pulse width and repetition rate are independently adjustable. Think of a drilling machine that lets you set “how hard each strike lands” and “how many strikes per second” independently—force and frequency are tuned separately without affecting each other. Ordinary Q-switched lasers are different: pulse width and repetition rate constrain each other, and MOPA breaks that restriction.
Power typically ranges from 100 to 300 watts. The higher the power, the thicker the glass it can handle and the faster the processing. But there is a trade-off between power and chipping quality—higher power means larger per-pulse energy, and chipping usually grows slightly. In real production, engineers need to find a balance between throughput and edge quality.
Major domestic brands:
- JPT M8 series: YDFLP-120-M8-S-W-V2 (120W), YDFLP-200-M8-S-W-V2 (200W), YDFLP-300-M8-S-W-V2 (300W). Wavelength 1064nm, MOPA architecture, beam quality M² better than 1.5, wide adjustable repetition rate range
- Guangzhi Technology (光至科技) (Wuhan): F-120-GT-10-N2-Pro+ (120W) and F-180-GT-10-N2-Pro+ (180W), pulse width 2-50ns, repetition rate 1-3000kHz, peak power above 100kW for both, M²<1.4, suited to precision drilling
There is also the green MOPA series at a wavelength of 532nm. Green light is absorbed far better in glass than infrared (infrared about 3-8%, green over 80%), penetrates less deeply, and reaches the ablation threshold at the focal point more easily; it works better on special glasses such as lead glass and colored glass.
Optical system: stepping the Z-axis focus upward
Bottom-up layer-by-layer ablation has to solve one problem: the focus must climb upward. There are two mature industrial implementations of this Z-axis focus control:
- Option 1: 2.5D galvo scanner—adds Z-axis focusing on top of X-Y, with a built-in high-speed Z-axis actuator (usually a voice coil motor), fast response, focal position error controllable at the 0.1-1 micron level. Like a precision “underwater engraving knife”: whichever layer the focus is in, the knife works in that layer
- Option 2: 2D galvo scanner + motion controller driving the Z axis—an ordinary 2D galvo handles X-Y scanning, while a motion controller (EtherCAT bus or pulse control) drives an independent Z-axis linear motor or lead screw. Advantage: long Z-axis stroke, suitable for drilling very thick glass (over 20mm); drawback: the Z axis responds more slowly than a 2.5D galvo, with mechanical delay when switching layers
One key parameter: 9 nanoseconds
Empirical finding from real production: a pulse width of 9 nanoseconds gives the best result—bottom-surface chipping can be kept within 150 microns, the smallest of all pulse width settings.
With a pulse width too short (6ns or less), peak power is extremely high and plasma shielding may occur—the light ionizes the air into a “barrier” that blocks the subsequent energy before it reaches the material, so utilization actually drops. With a pulse width too long (12ns or more), heat diffusion time increases and the heat-affected zone grows noticeably. 9 nanoseconds is exactly the “golden spot”—short enough to keep the heat-affected zone under control, long enough to avoid obvious plasma shielding.
Repetition rate matters too. Processing near the cutoff frequency gives the highest efficiency and the smallest chipping—the ablation crater of the previous pulse has not yet cooled when the next pulse arrives, so energy utilization is highest, with neither waste nor over-ablation.
Processing reference (9ns, near cutoff frequency):
| Glass thickness | 10mm-diameter hole | 20mm-diameter hole | 50mm-diameter hole |
|---|---|---|---|
| 1mm | about 1.9 s | about 4 s | about 9.7 s |
| 3mm | about 3.5 s | about 8 s | about 32 s |
| 5mm | about 6.1 s | about 12.3 s | about 46 s |
For micro holes (0.5mm diameter, 5mm thickness), chipping can be kept within 100 microns; the smallest hole diameter is 0.3mm; hole diameters cover the range 0.3-150mm.
Greatest advantage: through holes with almost no taper and extremely consistent diameters.
The laser focus always sits on the very bottom surface of the glass, so the hole wall is nearly vertical, with no taper. If the laser fired straight down from above with a fixed focus, the spot would grow larger toward the bottom and the hole wall would form an inverted cone—wide at the top, narrow at the bottom—a taper unacceptable for precision holes. Especially when the glass is already laminated to other components and cannot be flipped, the bottom-up method is virtually the only choice.
Two beam paths:
- Route 1 (through the glass, most common): the laser enters from above and passes through the glass; operators above face no extra safety risk, the machine configuration is simple, and no additional shielding is needed. Infrared light still loses 3-8% when passing through the glass, which generates a little heat—but that heat dissipates upward along the beam path and finally escapes from the top surface, so the heat-affected zone at the bottom surface where the focus sits stays relatively small. This is a natural “heat travels upward” advantage
- Route 2 (not through the glass): the laser enters directly from below the glass; 100% of the beam energy goes into bottom-surface ablation with no transmission loss, so edge quality is better (chipping can be pushed below 3 microns). The core reason: the heat-affected zone and micro-cracks of the bottom removal area lie outside the cutting contour, preserving the integrity of the top surface (the usable face) of the glass—the “damaged” part is removed and the “intact” part is kept. But there are two complications: operators above face an eye-injury risk and need an enclosure; debris flies upward and easily sticks to the F-Theta lens and galvo, requiring high-power dust extraction. This configuration costs about RMB 10000 more than Route 1
Limitations:
Chipping of 100-400 microns (fine for drilling, on the large side for precise contour cutting); speed 1-10mm/s; not suitable for large-area contour cutting or extremely thin glass (below 0.5mm).
It is unsuitable for large-area contour cutting for two reasons. First, speed cannot keep up—with layer-by-layer ablation, the glass must be ablated through as many layers as it is thick. For a 10cm × 10cm, 3mm-thick panel, if the depth of focus covers only 200 microns, at least 15 layers must be ablated; at a top speed of 10mm/s, cutting one contour line takes tens of seconds to minutes. CO₂ thermal stress cleaving runs at 100-1000mm/s and cuts the same 10cm contour in a fraction of a second to one second—dozens to a hundred times faster. Second, the galvo F-Theta lens field is limited—the field of an F-Theta lens is typically only 150×150mm to 300×300mm; beyond that, the glass must be moved or the scans stitched, which greatly increases complexity.
There is a deeper reason: the shorter the focal length of an F-Theta lens, the smaller the field, but the smaller the focused spot and the higher the energy density; enlarging the field requires a longer focal length, the spot grows, and energy density drops. If the spot area grows so large that energy density falls below the glass ablation threshold (about 2 J/cm²), the laser can no longer vaporize the glass. Field size and energy density are inherently in conflict—the energy density of large-field F-Theta lenses is often not enough to burn through glass, which is why drilling lenses generally do not exceed a 300×300mm field.
Who it suits: precision drilling, through holes, shaped holes—especially assembled products that cannot be flipped; thickness 0.5-20mm; chipping of 100-400 microns acceptable; budget RMB 200000-800000.
Method 2: Ultrafast Laser with a Bessel Cutting Head — the Standard of the Foldable-Screen Era
Before the details, consider foldable phones. The bend zone of a foldable screen is not ordinary-thickness glass but a special material called UTG (Ultra-Thin Glass), only 30-100 microns thick—thinner than a human hair. A layer of plastic (usually PI film) is laminated underneath to add toughness, so the whole module can both bend and survive.
Early foldables used CPI (colorless polyimide) plastic film, which bends but is not as hard as glass and scratches easily. Today the Huawei Mate X series and the Samsung Z Fold series all use UTG—better glass feel and better scratch resistance.
Foldable-screen makers spend heavily on femtosecond laser cutting equipment essentially to guarantee the quality of the glass edge. A femtosecond machine sells for RMB 3000000; spread over phones that retail at several thousand to over 10000 RMB each, the cost per glass panel is only a few RMB. Quality has a price.
Why can’t ordinary lasers cut precise contours?
The Rayleigh length of an ordinary laser focus is only a few tens of microns—the Rayleigh length is the distance over which the spot spreads from its minimum to 1.41 times that size. Cutting 1mm-thick glass would require moving the focus up and down repeatedly—extremely slow, with high machine complexity.
What is a Bessel beam?
A special beam shaped by an axicon or DOE: the central spot is only 1-2 microns (1/75 of a hair) wide, yet it keeps its size over several millimeters without spreading—like a fine “needle of light” plunging straight to the bottom, modifying or ablating the glass along the way.
Bessel beams have limits too: the central spot has extremely high energy density but limited total energy—good for fine processing, not for large-area fast cutting; the manufacturing precision of the axicon or DOE directly determines beam quality, and good versus poor optics differ by several times.
What is an ultrafast laser?
A picosecond is one trillionth of a second; a femtosecond is one quadrillionth of a second. The pulse ends before heat has any time to spread, so the surrounding material is almost unaffected.
| Laser type | Pulse duration | Heat-affected zone |
|---|---|---|
| Nanosecond laser | 1-200 nanoseconds | 20-100 microns |
| Picosecond laser | 1-10 picoseconds | below 5 microns |
| Femtosecond laser | below 1 picosecond | below 1 micron |
A nanosecond-cut edge may carry a ring of “baked” marks—yellowish color, rough edges, fine cracks. That ring is the heat-affected zone, and it is where the glass is most likely to break. A femtosecond-cut edge has almost no heat effect, clean as if cut by a blade, with edge strength close to that of the original glass.
Scheme 1: picosecond modification plus cleaving (the industry mainstream)
Step one: a picosecond laser with a Bessel head writes a “weakening line” inside the glass along the cutting path. The core mechanism is multiphoton absorption—a single 1064nm photon does not carry enough energy to ionize glass, but when several photons hit the same molecule at the same time, their combined energy triggers a structural change. This effect occurs only near the focus and barely affects the surface.
Step two: a CO₂ laser heats along the line; thermal expansion and contraction generate stress, and the glass splits along it. The whole process is like “drawing a line with the laser, then letting the glass break itself along the line”.
Cutting quality: chipping below 10 microns, speed 50-1000mm/s, edge strength retained above 80-90%, applicable thickness 0.1-6mm.
Representative equipment: the Light Blade series from HG Laser (picosecond + CO₂ two-step); the picosecond all-in-one machine from Shuidi Laser (水滴激光) (good value for money); and the TRUMPF TOP Cleave optics—one scan modifies the full thickness, with speeds up to 1 m/s, tens to a hundred times faster than conventional schemes. To put it simply: a conventional scheme traces a line back and forth with a fine pencil, while TOP Cleave paints the whole line in one pass with a wide brush.
Scheme 2: femtosecond direct ablation (for ultra-thin glass)
UTG is only 50-100 microns thick; the femtosecond laser burns away the entire line directly, with no cleaving step. Among all laser glass cutting schemes, this one delivers the highest quality.
Results: chipping below 3 microns, edge strength retained above 92% of the original panel.
The glass of a foldable screen is like the spine of a book, folded again and again. If the spine has micro-cracks, it breaks after a few folds. The femtosecond laser is the process that guarantees the integrity of the spine—it is not that it is expensive; it is that only it can meet the quality requirements of foldable screens.
A detail many people do not know: five low-energy pulses work better than one high-energy pulse—cleaner edges and fewer cracks. The reason is called the “defect accumulation effect”: the first pulses prime the material and create a tiny modified layer, which makes it easier for the following pulses to couple their energy. Like hammering a wall: one full-power swing may knock out cracks and chips; tap lightly a few times with a small hammer to create fine cracks, then strike with normal force, and the wall actually breaks more cleanly.
How to choose between the two schemes:
- Thickness above 100 microns with a chipping requirement within 10 microns → picosecond modification + cleaving
- UTG (50-100 microns) with a chipping requirement within 3 microns → femtosecond direct ablation
- Complex curves and fine contours → prefer TRUMPF TOP Cleave or Coherent SmartCleave (Coherent holds patent advantages in curve cutting and embedded cutting)
Who it suits: phone cover glass, foldable screens, medical device glass; thickness 0.03-6mm; budget RMB 1000000-5000000.
Method 3: CO₂ Laser Thermal Stress Cleaving — the Old Master’s Signature Technique
Before the principle, consider a scene you have certainly seen: in construction, how are large glass curtain walls cut? A 2m × 1m architectural glass panel needs to be cut to size. Burning it away bit by bit with a laser? Far too slow. Scoring it with a wheel? Architectural glass is usually 6-10mm thick—too hard to score. Ultrafast laser? Tens of RMB per meter, and over a hundred RMB to cut one panel—too expensive.
The answer: CO₂ laser thermal stress cleaving. A 2-meter line takes only a few seconds and costs a few RMB. That is the positioning of the CO₂ method—fast, cheap, and able to cut thick glass; exactly where the other methods struggle, it thrives.
Why is the CO₂ wavelength so special?
The CO₂ laser wavelength is 10.6 microns, a band whose energy is strongly absorbed by the Si-O bonds of glass—absorption above 90%, almost opaque.
For comparison: with 1064nm infrared laser light, glass absorbs only about 3-8%, so most of it passes through without heating anything; with the CO₂ laser at 10.6 microns, glass absorption is above 90%—the glass heats almost as soon as the light lands. The two wavelengths treat glass in completely different ways—infrared light passes through as if the glass were transparent, while CO₂ light treats it as opaque and heats it directly.
This difference comes from the molecular structure of glass. The main component of glass is silicon dioxide (SiO₂), and the Si-O bond responds differently to different wavelengths. 10.6 microns is exactly the “resonant absorption peak” of the Si-O bond—just as a tuning fork responds most strongly to a specific frequency, glass absorbs the CO₂ laser wavelength especially strongly.
How is the thermal stress generated?
When the CO₂ beam hits the glass surface, the temperature at the focal area rises above 1500°C in an instant, while the surrounding area is still at room temperature (assume 20°C)—a difference of more than 1400°C. With such a huge temperature difference, the material wants to expand but is held back by the cold material around it, which creates powerful internal stress. When the stress exceeds the fracture limit of glass (about 50-100 MPa), the glass bursts open along the laser scan path.
Simply put: heat it first, then crack it. Cracks propagate very fast; a cooling air jet (or water cooling) can be used to steer the crack and make it extend along the planned route.
The essential difference from the first two methods
The first two methods both work by “material removal”—using laser energy to vaporize the glass directly (ablation) or to weaken it (modification). CO₂ thermal stress cleaving is different: its principle is “stress-driven”—the laser does not need to burn through the glass, only to heat a line; the thermal stress then drives a crack along that line until the glass separates.
Bottom-up ablation: like scooping ice cream spoonful by spoonful until you dig through the whole cup
Ultrafast modification: like scoring a line on paper with a knife, then tearing it apart along the line
CO₂ thermal stress cleaving: like burning a string with a lighter—the string burns through, and the two parts separate
The knife is precise but slow; fire is imprecise but fast—this analogy helps you understand the efficiency gap between the three methods.
How do you keep the crack under control?
How can you make sure a crack produced by thermal stress follows the planned route instead of bursting apart randomly? The answer is temperature gradient control. Wherever the laser points, the temperature rises highest; stress concentrates along the laser scan path, so the crack tends to extend along the line. At the same time, a cooling air jet is used—cold air is blown behind the laser to create a colder zone, and the crack extends along the boundary between the hot zone and the cold zone. The operator acts like a “commander”, coordinating the laser (heat source) and the airflow (cold source) to guide the crack forward along the planned route.
Three key parameters
The result of CO₂ laser thermal stress cleaving is governed mainly by three parameters:
- Laser power (30-150W): too little power means the temperature is not high enough, the stress cannot drive a crack, and it will not cut; too much power enlarges the heat-affected zone and degrades edge quality
- Scan speed (100-1000mm/s): a faster speed means less heat accumulation and better quality, but it requires more power to match; too slow means overheating and a larger heat-affected zone
- Defocus—the most critical parameter
Defocus refers to the position of the focal point relative to the glass surface:
- Positive defocus: the focus is above the glass surface; the heated zone lies at the glass surface and extends somewhat downward
- Negative defocus: the focus is inside the glass; the heated zone lies inside the glass
- Zero defocus: the focus is exactly on the glass surface
Positive defocus makes the heated zone wider and the temperature gradient gentler, avoiding uncontrolled cracks caused by local overheating. Negative defocus concentrates the heating but tends to produce irregular micro-cracks.
The optimal defocus depends on glass thickness:
| Glass thickness | Recommended defocus | Reason |
|---|---|---|
| below 1mm | +1-2mm | Little thermal stress is needed; no large heated zone required |
| 1-3mm | +2-4mm | A larger heated zone is needed to generate enough thermal stress |
| above 3mm | +3-6mm | The thicker the glass, the larger the heated zone needed, and the defocus must also increase |
With the right defocus, the crack runs cleanly along the planned route. With the wrong defocus, either it will not crack at all, or it shatters chaotically. It is like burning a string: a flame too small will not burn it through, and a flame too big burns it all at once and chars the edges. Finding the right amount of heat so that it just burns through with a clean edge takes accumulated experience.
Its real advantages
The CO₂ method has three advantages that are hard to replace:
- Extremely low cost: a 30-150W CO₂ laser source can be bought for RMB 30000-150000. A complete cutting system can be put together for RMB 150000-500000
- Fastest speed: straight-line cutting at 100-1000mm/s, the fastest of the three methods. Of course, that speed comes at the price of larger chipping—high speed and small chipping are still a contradiction today. For architectural glass this is not a problem: chipping of 20 microns is fully acceptable and no secondary polishing is needed
- It cuts thick glass: it handles thicknesses from 0.5mm to 12mm, and some special configurations can cut even thicker. Ultrafast lasers are limited by the depth of focus of the Bessel head and usually handle only up to 6mm; bottom-up ablation is too slow for thick glass—imagine 10mm-thick glass, tens of microns per layer, hundreds of layers, a few seconds per layer: more than ten minutes per panel. The CO₂ method fills the market gap in thick-glass cutting
Application scenarios in detail
- Architectural glass: straight-line cutting of large curtain-wall panels, flat glass, and tempered glass (pre-cut). Architectural projects are usually large-batch, standardized straight cuts, where the cost and speed advantages of the CO₂ method are fully exploited. Key point: physically tempered glass cannot be cut (see the taboos below)
- Automotive glass: straight cutting and pre-cutting of windshields and side windows. Automotive glass is usually 3-6mm thick—exactly the range the CO₂ method is best at. The automotive industry demands high cutting speed (mass production) and only moderate edge quality (edge wrapping and assembly come later), and the CO₂ method matches these needs perfectly
- PV glass: the ultra-clear glass used in solar panels, 2-6mm thick, is also cut in large-area straight lines, and the CO₂ method is the first choice. The PV industry is extremely cost-sensitive, where the low cost of the CO₂ method is highly competitive
Two glasses it cannot cut
- Quartz glass: its thermal expansion coefficient is extremely low (roughly one tenth that of ordinary glass), so almost no thermal stress develops. When CO₂ light strikes it, the temperature rises but the material barely expands—no stress is generated, so it cannot be cut. Quartz glass needs an ultrafast laser solution. To put it simply: ordinary glass is like modeling clay, expanding obviously when heated; quartz glass is like ceramic, barely deforming when heated—so the principle of thermal stress cleaving simply does not apply to it
- Physically tempered glass: it carries huge internal pre-stress (the very source of its strength); any tiny surface disturbance releases the stress and shatters the whole panel instantly. Physically tempered glass must never be cut—all machining must be completed before tempering. This is not a matter of technique but of physics—the strength of tempered glass comes exactly from that pre-stress; once cutting disrupts the stress structure, the whole panel loses stress balance and bursts apart instantly. The CO₂ method is often used for the “pre-cutting” step before physical tempering
CO₂ and ultrafast lasers are not competitors
One thing worth stressing: the CO₂ method is often used together with ultrafast lasers in a “two-step” process.
- Step one: a picosecond laser writes a weakening line inside the glass (this is precise, controlled modification)
- Step two: a CO₂ laser heats along the line, generating thermal stress that splits the glass (this exploits the fast heating capability of CO₂)
Here the CO₂ laser plays the role of a “cleaving tool”, not a “cutting tool”. It makes up for the slow cleaving speed of an ultrafast laser working alone, while exploiting its own fast-heating strength.
So in the two-step process, the CO₂ laser is a good partner of the ultrafast laser, not its rival. That is exactly why ultrafast equipment makers such as HG Laser and Han’s Semiconductor also integrate CO₂ laser sources into their machines—CO₂ is not a technology to be replaced; it has found its proper place in the whole process chain.
Industry status
CO₂ laser technology is already very mature. The world’s major CO₂ laser suppliers include Coherent and Synrad (a Novanta company); domestic RF slab CO₂ lasers have also improved rapidly in recent years and offer strong value for money.
In glass cutting equipment, domestic machine builders are quite mature and pricing is relatively transparent. When choosing equipment, focus on: chipping size, cutting speed, maximum processable thickness, machine stability, and after-sales response.
For architectural and automotive glass makers, the CO₂ method remains the most cost-effective choice. This method will not disappear; it will keep evolving toward intelligence—intelligent defocus, dual-laser coordination, and two-step pairing with ultrafast lasers are all future directions.
Who it suits: architectural glass (curtain walls, pre-cutting), automotive windshields (3-6mm, mass production), PV glass; thickness 0.5-12mm; budget RMB 150000-500000.
Full Comparison
| Bottom-up layer-by-layer ablation | Ultrafast laser + Bessel head | CO₂ thermal stress cleaving | |
|---|---|---|---|
| Chipping | 100-400 microns | 3-10 microns | above 20 microns |
| Speed | 1-10mm/s | 50-1000mm/s | 100-1000mm/s |
| Shapes | any (best at drilling) | straight lines + complex curves | straight lines or large arcs |
| Thickness range | 0.5-20mm | 0.03-6mm | 0.5-12mm |
| Equipment cost | RMB 200000-800000 | RMB 1000000-5000000 | RMB 150000-500000 |
| Typical applications | phone holes, through holes, precision drilling | foldable screens, phone covers, medical glass | architectural glass, automotive glass, PV glass |
Selection Rule of Thumb
Nanosecond for drilling, femtosecond for thin glass, CO₂ for thick-glass straight cuts, and the two-step process when you need both quality and speed.
- Only need holes and through holes, limited budget → bottom-up layer-by-layer ablation
- Phone covers and foldable screens with high edge-quality requirements → picosecond modification + CO₂ cleaving
- Ultra-thin UTG (50-100 microns) with chipping within 3 microns → femtosecond direct ablation
- Large-area straight cuts in thick glass, limited budget → CO₂ thermal stress cleaving
- Quartz glass → only ultrafast laser works
- Physically tempered glass → cut only before tempering; absolutely never touch it after



Leave a Reply