F-Theta Field Lens Selection Guide
Master the key parameters, select precisely, and avoid the pitfalls
Introduction
The field lens, fully known as the flat-field focusing lens (F-Theta lens), is the core optical component of laser marking, cutting, welding, engraving, and other equipment. Its role is to form a focused spot of uniform size and consistent depth of focus across the entire working plane, ensuring consistency in machining accuracy.
Why is it called “F-Theta”?
- F = focal length (Focal Length)
- θ = scan angle (Theta, the deflection angle of the galvo scanner)
The core property of F-Theta optics is: image height (spot position) = focal length × scan angle, i.e. y = f × θ
Why can’t an ordinary lens be used?
An ordinary lens follows the y = f × tanθ relation, and tanθ is a nonlinear function:
- When θ goes from 0° to 10°, y changes by Δy₁
- When θ goes from 20° to 30° (the same angle change), the change in y, Δy₂, is far larger than Δy₁
This leads to:
1. Uneven scanning speed – the galvo rotates at constant speed, but the spot “moves faster and faster”
2. Pattern distortion – you want to mark a square, but it comes out “pillow-shaped”
3. Field curvature – the focal points do not lie in one plane; the edges go out of focus
How the F-Theta field lens solves it
The F-Theta field lens uses carefully designed negative distortion to cancel the nonlinear growth of tanθ:
- Ordinary “distortion” is an optical defect, but an F-Theta field lens deliberately introduces exactly the right amount of barrel distortion
- This negative distortion “presses down” and “straightens” the nonlinear curve
- The result is a perfectly linear relationship between image height and scan angle
Internal structure of a field lens
A field lens is not a single lens element but a combination of multiple curved lens elements:
Incoming beam → [Lens 1] → [Lens 2] → [Lens 3] → focused spot
↓
aberration-corrected design
↓
flat-field focusing (all focal points in one plane)
When the laser enters at different angles, the internal lens elements eliminate aberrations such as field curvature and distortion, ensuring that the outgoing beam focuses onto the same plane.
This article systematically explains the core parameters of field lenses, the selection procedure, and the pairing rules, to help you make the right selection decision.
1. Core Parameters of a Field Lens in Detail
1. Working wavelength
Definition: the laser wavelength for which the field lens coating is designed.
Why it matters: the lens coating is designed for a specific wavelength, and a wavelength mismatch will cause:
– coating burnout
– reduced transmission
– severe energy loss
Common wavelength chart:
| Laser type | Wavelength | Field lens type |
|---|---|---|
| Fiber laser | 1064nm | YAG field lens |
| UV laser | 355nm | UV field lens |
| Green laser | 532nm | Green field lens |
| CO2 laser | 10.6μm | CO2 field lens |
Selection rule: the field lens wavelength must strictly match the laser wavelength!
2. Focal length and scan field
Focal length: the distance from the optical center of the field lens to the focal plane; the core parameter that determines the working field.
Scan field: the effective working area the field lens can cover.
Rule-of-thumb formula:
Scan field (mm) ≈ 0.7 × focal length (mm)
Chart of common focal lengths and fields:
| Focal length | Scan field | Application |
|---|---|---|
| F63 | 50×50mm | ultra-fine marking / micromachining |
| F100 | 70×70mm | small-field fine marking |
| F160 | 110×110mm | standard marking |
| F210 | 150×150mm | medium-field marking |
| F254 | 175×175mm | medium-to-large field marking |
| F300 | 200×200mm | medium-to-large field precision machining |
| F330 | 220×220mm | large-field marking |
| F380 | 250×250mm | large-field precision machining |
| F420 | 300×300mm | large-field applications |
How focal length relates to performance:
| Focal length | Spot size | Energy density | Precision | Typical use |
|---|---|---|---|---|
| Short focal length | small | high | high | fine marking, micromachining |
| Long focal length | large | low | average | large fields, deep depth-of-focus needs |
3. Entrance pupil (clear aperture)
Definition: the maximum beam diameter the field lens can accept.
Why it matters: the entrance pupil determines which galvo beam diameter the field lens can be paired with.
Selection rule:
Field lens entrance pupil ≥ galvo beam diameter
Common entrance pupil sizes: 10mm, 12mm, 14mm, 15mm, 20mm, 30mm
Pairing examples:
– a galvo with a 10mm beam needs a field lens with an entrance pupil ≥10mm
– a galvo with a 20mm beam needs a field lens with an entrance pupil ≥20mm
– a galvo with a 30mm beam needs a field lens with an entrance pupil ≥30mm
4. Working distance
Definition: the distance from the mounting face of the field lens to the workpiece surface.
Why it matters:
– it determines the Z-axis mounting height of the machine
– it affects workpiece fixturing height and space layout
– it is related to the machine column height
Notes:
– working distance ≠ focal length (usually working distance > focal length)
– large-field lenses have longer working distances and need taller columns
– take into account the height of the workpiece itself
Column height reference:
| Field of the lens | Working distance | Recommended column height |
|---|---|---|
| 110×110mm | about 180mm | 400mm |
| 175×175mm | about 280mm | 550mm |
| 300×300mm | about 480mm | 700mm |
| 400×400mm | about 600mm | 1000mm |
5. Focused spot diameter
Definition: the smallest spot size after the laser is focused.
Calculation formula:
Spot diameter = K × λ × f / D
Where:
– K = a constant (about 1.83, related to pupil illumination)
– λ = laser wavelength
– f = focal length of the field lens
– D = incident beam diameter
Factors affecting spot size:
| Factor | Relationship | Explanation |
|---|---|---|
| Focal length | positive | the longer the focal length, the larger the spot |
| Wavelength | positive | the longer the wavelength, the larger the spot |
| Incident beam | inverse | the larger the incident beam, the smaller the focused spot |
How to get a small spot:
1. choose a field lens with a short focal length
2. choose a laser with a shorter wavelength
3. use a high-magnification beam expander to enlarge the incident beam
6. Scan angle
Definition: the maximum beam deflection angle the field lens allows.
Why it matters: together with the swing angle of the galvo, it determines the actual working field.
Common scan angles: ±11°, ±14.8°, ±15°, ±17.3°, ±20°, ±28°
Selection rule:
Galvo swing angle ≤ scan angle allowed by the field lens
If the galvo swing angle falls short of the maximum angle allowed by the field lens, the actual field will be smaller than the nominal field.
2. Choosing the Field Lens Type
1. By design type
| Type | Features | Advantages | Disadvantages | Typical use |
|---|---|---|---|---|
| Ordinary field lens (F-Theta) | telecentric angle 4°-17° | large field, fast, affordable | edge spot slightly larger | most laser processing scenarios |
| Telecentric field lens | telecentric angle 0°-4° | consistent spot, high precision | expensive, bulky | precision drilling (perpendicularity required), precision marking, cutting, machine vision |
Principle of the telecentric field lens
What is telecentric design?
In an ordinary F-Theta field lens:
– the central beam strikes perpendicular → round spot ✓
– the beams at the edges strike obliquely → elliptical spot ✗
Telecentric field lens design ensures: all beams strike the working surface perpendicular
Ordinary field lens: Telecentric field lens:
╲ ╱ │ │
╲╱ │ │
───── ─────
edges oblique all perpendicular
Advantages of telecentric design:
1. Consistent spot shape – round spot from center to edge
2. Consistent spot size – uniform machining depth/line width
3. Higher precision – removes machining errors caused by oblique incidence
4.High perpendicularity-vertical drilling required
The cost of telecentric design:
– requires a larger front lens
– larger and heavier lens body
– higher manufacturing cost (usually 5-20x more expensive)
When do you need a telecentric field lens?
– precision cutting (uniform kerf width required)
– micromachining (micron-level precision)
– machine vision inspection
– 3D marking / deep-cavity machining
-vertical marking of micro-holes
2. By material
| Material | Features | Power range | Price | Typical use |
|---|---|---|---|---|
| Optical glass (K9, etc.) | cheap, stable performance | low power | low | ordinary marking machines |
| Quartz (fused silica) | high damage threshold, low thermal drift | medium-high power | high | high-power, high-stability needs |
| Zinc selenide (ZnSe) | high transmission at 10.6μm | all power levels | high | CO2 lasers only |
Material selection key points
Optical glass:
– low cost, high value
– suits routine marking applications (20W-50W)
– prolonged high-power use may cause thermal effects
Fused silica:
– high damage threshold, withstands high power
– small thermal expansion coefficient, minimal thermal drift
– first choice for lasers above 50W
– mandatory for ultrafast lasers (picosecond, femtosecond)
Zinc selenide (ZnSe):
– dedicated to CO2 lasers (10.6μm wavelength)
– extremely high transmission of infrared light
– fairly expensive, but irreplaceable
3. By application area
| Application | Recommended field lens type | Special requirement |
|---|---|---|
| Laser marking | ordinary F-Theta | choose focal length by field size |
| Laser cutting | telecentric field lens | high demand for spot consistency |
| Laser welding | quartz field lens | high power, heat resistant |
| 3D printing | large-field field lens | long working distance |
| Laser cleaning | large-entrance-pupil field lens | paired with large-beam galvo |
| Micromachining | telecentric + quartz | high precision + high power |
3. Pairing Rules Between Field Lens and Galvo Scanner
Rule 1: beam diameter matching
Core principle: field lens entrance pupil ≥ galvo beam diameter
| Galvo beam diameter | Field lens entrance pupil required | Consequence of mismatch |
|---|---|---|
| 7mm | ≥7mm | pupil < beam: field shrinks |
| 10mm | ≥10mm | pupil < beam: field shrinks |
| 15mm | ≥15mm | pupil < beam: field shrinks |
| 20mm | ≥20mm | pupil < beam: field shrinks |
| 30mm | ≥30mm | pupil < beam: field shrinks |
Reverse trick: when the field lens entrance pupil is > the galvo beam diameter, you can actually mark a field larger than the nominal field!
Rule 2: scan angle matching
Core principle: galvo swing angle ≤ scan angle allowed by the field lens
| Angle allowed by lens | Galvo swing angle | Actual field |
|---|---|---|
| ±15° | ±15° | reaches nominal field ✓ |
| ±15° | ±11° | below nominal field ✗ |
| ±20° | ±11° | below nominal field ✗ |
Rule 3: wavelength matching
Core principle: the wavelengths of galvo, field lens, and laser must match
| Laser | Galvo | Field lens |
|---|---|---|
| 1064nm fiber laser | 1064nm galvo | 1064nm field lens |
| 355nm UV laser | 355nm galvo | 355nm field lens |
| 532nm green laser | 532nm galvo | 532nm field lens |
| 10.6μm CO2 laser | 10.6μm galvo | 10.6μm field lens |
Consequences of mismatch: coating damage, energy loss, equipment damage
4. Selection Decision Workflow
Step 1: determine the working wavelength
Determine the field lens wavelength from the type of laser.
Step 2: determine the working field
Set the scan field from the product size, then back-calculate the focal length:
Focal length = field ÷ 0.7
Step 3: match the galvo parameters
- field lens entrance pupil ≥ galvo beam diameter
- field lens scan angle ≥ galvo swing angle
Step 4: confirm the working distance
Based on the machine column height and the workpiece height, choose a field lens with a suitable working distance.
Step 5: confirm the thread interface
Common thread specifications: M85×1, M79×1, M102×1, M55×1, etc., which must match the galvo.
Step 6: choose the material and type
- low power: optical glass
- high power: quartz
- precision machining: telecentric field lens
- general machining: ordinary field lens
Recommended brands
Imported brands:
- LINOS (Germany): high-precision field lenses, stable quality
- SILL Optics (Germany): a field lens specialist with authoritative technical documentation
- JENOPTIK (Germany): high-end optical components, excellent performance
Domestic brands:
- Wavelength Opto-Electronic (Nanjing): well-standardized field lens design, high value for money
- Tiankai Optoelectronics (Days凯光电) (Suzhou): complete field lens and galvo pairing
Special requirements of coaxial-vision marking and welding machines
Marking and welding machines equipped with coaxial vision systems place special requirements on the field lens; the following factors need extra consideration:
1. Beam split ratio requirements
| Configuration type | Laser split ratio | Vision split ratio | Typical use |
|---|---|---|---|
| Standard configuration | 90% | 10% | ordinary marking and welding |
| High-precision vision | 70-80% | 20-30% | precision positioning, QR code reading |
| Low-power vision | 95% | 5% | high-power welding |
2. Working distance matching
- the working distance of the field lens must match the focal distance of the vision system
- common vision working distances: 100mm, 160mm, 210mm
- make sure the laser focus and the vision focus lie in the same plane
3. Field lens entrance pupil size
- the entrance pupil diameter must be larger than the vision beam-splitting prism
- common prism sizes: 10mm, 15mm, 20mm
- make sure the field lens entrance pupil ≥ the prism diagonal
4. Selection recommendations for coaxial-vision field lenses
- Entry level: F160 + 10%/90% split ratio, for standard marking
- Industrial grade: F210 + 20%/80% split ratio, for precision welding
- High-end vision positioning: F100 + 30%/70% split ratio, for high-precision positioning
5. FAQ
Q1: Why does my 110×110mm field lens only mark 80×80mm?
Possible causes:
1. galvo beam diameter > field lens entrance pupil → replace with a field lens with a larger entrance pupil
2. galvo swing angle < angle allowed by the field lens → replace with a galvo with a larger swing angle
Q2: I want to mark 200×200mm — what focal length should I choose?
Calculation: focal length = 200 ÷ 0.7 ≈ 285mm
You can choose an F290 field lens (actual field about 200×200mm, suitable) or an F330 field lens (actual field about 220×220mm, a good fit).
Q3: The field lens entrance pupil is much larger than the galvo beam diameter — is that a problem?
No problem! It is actually beneficial:
– the beam is not clipped
– you can mark a field larger than the nominal field
– spot consistency is better
Q4: Is a large-field lens or a small-field lens better?
Bigger is not always better; it depends on the need:
– small-field lens: small spot, high precision, high energy density, but shallow depth of focus—if the product surface rises and falls, results may come out inconsistent, with uneven marking darkness.
– large-field lens: large field, but a bigger spot and lower precision; however, it can deliver consistent results on products with some surface variation.
Choose according to your actual processing needs, or keep several field lenses of different field sizes.
Q5: Which field lens for ultrafast lasers?
A:
- Must use: fused silica material (high damage threshold)
- If distortion and telecentricity requirements apply: telecentric quartz field lens
- Distortion value: <0.1% (ordinary field lenses are typically 0.5-1%)
- Applications: precision measurement, PCB drilling, micromachining
- Price: about 3-5x that of an ordinary field lens
Q6: When is a telecentric field lens needed?
It depends on the application:
– ordinary marking: an ordinary field lens is enough, with better value for money
– precision marking/cutting/machine vision: a telecentric field lens is more suitable
– sufficient budget: a telecentric field lens gives better results
6. Cost-Saving Selection Tips
Tip 1: small-beam galvo + large-entrance-pupil field lens
Principle: use a short-focal-length field lens to cover a large field while keeping a small spot and high precision
Cost comparison:
| Option | Configuration | Spot | Cost |
|---|---|---|---|
| Option A | high-power laser + long-focal-length field lens | large | high |
| Option B | low-power laser + small-beam galvo + large-entrance-pupil field lens | small | low |
Conclusion: for large field + high precision, Option B saves money!
Tip 2: keep several spare field lenses
Keep field lenses of different field sizes for different product dimensions:
– use a short-focal-length field lens for small products (high precision)
– use a long-focal-length field lens for large products (large field)
Tip 3: thread adapter ring
If the field lens thread does not match the galvo, a thread adapter ring can be made—no need to replace the galvo or the field lens.
7. Summary
Core points of field lens selection
| Parameter | Selection rule |
|---|---|
| Wavelength | must match the laser |
| Focal length | field ≈ 0.7 × focal length |
| Entrance pupil | ≥ galvo beam diameter |
| Working distance | matched to the column height |
| Scan angle | ≥ galvo swing angle |
| Material | chosen by power |
| Type | chosen by precision needs |
Three pairing rules
- Beam matching: field lens entrance pupil ≥ galvo beam diameter
- Angle matching: galvo angle ≤ angle allowed by the field lens
- Wavelength matching: all three wavelengths identical
One money-saving tip
Small-beam galvo + large-entrance-pupil field lens = large field + high precision + savings
## Disclaimer
This article is compiled from industry expertise; for actual selection, combine the real equipment parameters with advice from professional engineers.
Compiled by the technical team of Changsha Soar Laser Equipment Co., Ltd. Inquiries are welcome.
**Phone**: 15927220467, 17671454691
**Email**: 859818709@qq.com, panhongsheng_521@hotmail.com
**WeChat**: 15927220467



Leave a Reply