Source: Soar Laser Components
Companion article: “A Complete Guide to Controlling Thermal Effects in Laser Processing”—the previous part covered avoiding heat; this part covers harnessing it
After the previous article “A Complete Guide to Controlling Thermal Effects in Laser Processing” was published, many colleagues commented that they wanted to see the positive applications of thermal effects. Today it is here—from avoiding heat to harnessing heat, a walkthrough of the underlying logic of laser processing.
1. A Counter-Intuitive Industry Claim: Is So-Called “Cold Processing” Really Heat-Free?
In laser circles a widely circulated claim goes: UV lasers are “cold processing”, picosecond lasers are “cold processing”—implying that these processes have no thermal effects.
That is half right, but wrong at the crucial point.
The truth: so-called cold processing does not mean there is no heat; it means the heat has no time to spread.
Picosecond lasers have pulse widths on the order of 10-12 seconds. Within that timescale, the material absorbs photon energy and its temperature instantly soars above the vaporization point, yet the characteristic distance of heat diffusion is only micrometers—the processing is finished before the heat has had any chance to conduct to the surroundings. So the “cold” you see is essentially an extremely short heat-application time and an extremely small heat-diffusion range, not the absence of thermal effects.
The previous article discussed avoiding heat—how to insulate, dissipate, and eliminate heat, keeping unwanted thermal effects at bay. But the other side of laser processing is precisely using heat: hardening relies on heat, welding relies on heat, cladding relies on heat, and cutting relies on heat even more.
So what is the highest level of a laser process engineer?
Perfectly isolate the heat that should be avoided; precisely control the heat that should be used.
Mastering both cold and heat, applying heat on demand—that is real skill. In this article we focus specifically on “harnessing heat”.
2. Layer One: Shallow, Controllable Thermal Effects
Modifies only the surface layer without melting the substrate—power density 10³~10⁵ W/cm², thermal effects confined to the surface, precise and controllable
1. Laser hardening: the self-quenching magic of ultra-high-temperature rapid heating
When it comes to laser hardening, many operators instinctively assume: quenching means gentle heating followed by cooling. This understanding is completely wrong.
Here comes the key point: laser hardening does not need cooling water.
Why? Because laser heating acts only on an extremely thin surface layer (typically 0.1-1.5mm). Once the laser moves away, the massive cold substrate underneath is the best “quenching medium”—heat is conducted into the substrate interior at extreme speed, with a cooling rate that likewise reaches 104-105°C/s, far exceeding the critical cooling rate of martensitic transformation (the core microstructural transformation behind steel hardening), so the surface completes the austenite-to-martensite transformation directly.
This is called laser self-quenching (Self-quenching): the substrate’s own extremely fast thermal conduction brings the temperature down, with no external cooling system required.
This self-quenching mechanism brings three direct advantages:
Higher hardness—because the cooling rate is extremely fast, the martensitic transformation is more complete, and surface hardness is typically 15%-20% higher than conventional induction hardening.
Minimal distortion—the heat acts only on the surface layer, the substrate is essentially unaffected, and the workpiece barely deforms.
No cracking risk—both the heating and cooling gradients stay within controllable ranges, so quench cracking does not occur.
Typical applications: gear tooth flank hardening (case depth 0.3-0.8mm, tooth flank hardness up to HRC55-62), mold cavity strengthening (only the cavity surface is hardened, no overall annealing), machine tool guideway surface hardening, and more.
2. Laser cleaning: the dual mechanism of thermal-stress spallation and micro-vaporization
Laser cleaning is widely discussed in the industry, but most people focus only on the selling point of “no damage to the substrate” and rarely understand it from the perspective of thermal effects. Yet thermal effects are precisely the core driving force of laser cleaning.
Laser cleaning is fundamentally different from melting-based processing: it does not ablate or melt the substrate and relies on the combination of two thermodynamic mechanisms:
Mechanism one: thermal-stress spallation (thick contaminant layers)
When pulsed laser light hits a surface covered by a thick contaminant layer, the contaminant and the substrate absorb energy and heat up within an extremely short time. Because the contaminant (rust, paint, oxide films, etc.) and the substrate have different thermal expansion coefficients, a huge shear stress arises at the interface—the larger the difference in thermal expansion coefficients, the greater the stress. Once this stress exceeds the bond strength between the contaminant and the substrate, the contaminant is stripped off and ejected instantly.
Mechanism two: micro-vaporization blow-off (thin contaminant layers)
For thin contaminants (oil films, thin oxide layers), the driving effect of the thermal expansion mismatch is not strong enough. In that case the power density must be raised to the 105 W/cm² level so that the contaminant surface micro-vaporizes directly—the instantaneous volume expansion produced by vaporization creates a recoil force, and like a miniature “blast of wind” it blows the remaining contaminants clean away.
Both mechanisms rely purely on thermodynamic effects: the substrate is not melted, burned, or dissolved; separation is achieved entirely through thermal-stress differences and micro-vaporization.
Once you understand these two thermodynamic mechanisms, you can see why laser cleaning “does not damage the substrate”: the substrate itself is never melted or vaporized; it merely serves as the “anchor” for thermal expansion—the contaminant expands while the substrate stays still, stress concentrates at the interface, and the two naturally separate; micro-vaporization acts only on the contaminant surface, the recoil force points outward, and the substrate remains intact.
Operating points: keep the power density below the substrate damage threshold; choose a nanosecond pulse width (enough thermal shock without letting heat diffuse into the substrate); adjust the frequency according to cleaning efficiency and contaminant type. Use thermal-stress spallation mode for thick contaminants and switch to micro-vaporization mode for thin ones.
3. Laser annealing: the repair power of gentle heat diffusion
In contrast to the “extreme speed” of hardening, laser annealing takes the low-temperature, slow-heating route: a laser of relatively low power density heats the material slowly, with the temperature kept below the recrystallization temperature, allowing lattice defects to heal themselves under thermal activation and relieving residual processing stress.
Typical scenarios: post-ion-implantation annealing of semiconductor wafers and stress relief of stainless-steel welds. The core idea: thermal effects can be applied “very lightly”—light enough to repair defects without changing the microstructure.
3. Layer Two: Melting-Level Thermal Effects
The core industrial value zone—power density 10⁵~10⁶ W/cm², melting the material and then precisely controlling solidification
1. Laser welding: the keyhole effect and the heat-input dilemma
In the deep-penetration mode of laser welding, the core mechanism is the keyhole effect (Keyhole effect): a high-power-density laser beam (>106 W/cm2) strikes the metal surface, the metal vaporizes instantly to form a deep cavity, and the laser penetrates deep into the material through this channel; the molten metal on the cavity walls, held by surface tension, maintains the cavity shape and forms a “keyhole”-shaped weld pool—this is the signature feature of deep-penetration welding.
But what really troubles the process engineer is not the keyhole itself—it is the heat-input dilemma:
Too much heat: an overly wide heat-affected zone, coarse grains, and a soaring risk of hot cracking.
This contradiction is especially typical for aluminum alloys and high-strength steels—aluminum alloys have high thermal conductivity and need high heat input to achieve full penetration, yet high heat input readily causes hot cracking; high-strength steels are extremely sensitive to heat input, and overheating directly softens the heat-affected zone.
The mainstream industrial solution to this dilemma is wobble welding (Wobble Welding): the laser beam oscillates along a preset path, widening the weld pool while lowering the temperature gradient. Wobbling brings benefits on many fronts: the wider weld pool improves the weld’s gap-bridging capability; the lower temperature gradient refines the grains; and the more uniform heat input effectively suppresses hot cracking. Typical parameters: oscillation frequency 50~200 Hz and amplitude 0.5~2mm, tuned according to plate thickness and joint type.
So the core process logic of laser welding is not “tweak the power until it feels right”, but rather using controllable thermal gradients combined with wobble welding to balance penetration depth against cracking risk. Specifically:
Conduction mode (low power density) has low heat input, shallow penetration, and a narrow heat-affected zone, making it suitable for thin sheets and precision parts; keyhole mode (high power density) achieves deep penetration through the keyhole effect, but the heat input must be precisely controlled, otherwise the keyhole becomes unstable and causes porosity and cracks. When welding high-strength steel, heat input is usually kept within the narrow range of 1-3 kJ/m; when welding aluminum alloys, filler wire is often added to dilute low-melting-point eutectic constituents and reduce crack sensitivity.
In one sentence: controlling thermal effects in welding is a tightrope walk between “full penetration” and “no cracking”.
2. Laser cladding: dilution rate as the thermal-control code
Laser cladding is another typical process where “more heat is not necessarily better”.
The core metric of cladding is the dilution rate—the proportion of substrate melted into the cladding layer at their interface. If the dilution rate is too high, the substrate melts in excessively, the coating composition is diluted, and wear/corrosion performance drops sharply; if it is too low, the coating bonds poorly to the substrate and tends to spall.
Below 5%: insufficient metallurgical bonding, poor coating adhesion, easy spalling.
Above 15%: the coating is over-diluted by the substrate and performance metrics fall off a cliff.
The dilution rate is essentially the quantitative expression of thermal effects: the higher the heat input, the more substrate melts in, and the higher the dilution rate. So what cladding tunes is not power but the match between heat input and powder feed rate—keep the heat input as low as possible while ensuring metallurgical bonding, holding the dilution rate in the golden range of 5%-15%.
Typical applications: wear-resistant coating repair for mining machinery (Stellite cobalt-based alloy clad onto hydraulic rod surfaces, hardness HRC45-55), corrosion-resistant repair of power-plant boiler tubes, roll surface strengthening, and more. The common feature of these scenarios: the coating must be both hard and well bonded, and precise control of heat input is the only way out.
4. Layer Three: Extreme Vaporization-Level Thermal Effects
The extreme of thermal effects—power density 10⁶~10⁸ W/cm², driving the material straight to vaporization
1. Laser cutting: three mechanisms, each with its own role
On the surface, the thermal-effect logic of laser cutting looks simple—high heat melts the material and the assist gas blows away the slag—but cut quality depends entirely on which mechanism is used and how the heat is controlled. Depending on power density and assist gas, laser cutting actually divides into three mechanisms:
① Fusion cutting
An inert gas (nitrogen, argon) blows away the molten metal; the laser is only responsible for heating and melting, and the gas takes no part in the reaction. Heat input is relatively controllable and the heat-affected zone is narrower.
Typical materials: stainless steel, aluminum alloysFeatures: narrow HAZ, minimal cut oxidation
② Oxidation cutting
Oxygen is used as the assist gas and reacts exothermically with the high-temperature metal, effectively “adding fuel to the fire”—heat input increases substantially and cutting speed rises markedly, but at the cost of a wider heat-affected zone and an oxide layer on the cut edge.
Typical materials: carbon steelFeatures: fast speed, large HAZ
③ Vaporization cutting
At high power density, the material vaporizes directly from the solid state, with no liquid slag involved. The cut is the cleanest and the heat-affected zone the smallest, but the demands on laser power and beam quality are the highest.
Typical materials: non-metals, ceramicsFeatures: best cut quality
How to choose among the three mechanisms: use oxidation cutting on carbon steel for efficiency, fusion cutting on stainless steel/aluminum alloys to protect quality, and vaporization cutting on non-metals/ceramics for precision. The key point: the heat-input mode and magnitude differ completely across mechanisms, and the parameter-matching logic changes accordingly—power density, cutting speed, and assist-gas pressure must each be matched to the right mechanism.
2. Laser drilling: high-energy thermal vaporization in ultra-short time
Laser drilling is the most “brute-force” application of thermal effects: concentrating high energy on an extremely small area within an extremely short time so the material jumps directly from solid to gas (sublimation), enabling micro-hole and deep-hole machining.
Unlike cutting, drilling leans more toward “vaporization plus ejection” and places higher demands on laser peak power. For the film-cooling holes of aero-engine turbine blades (0.3-0.8mm diameter, depth-to-diameter ratio >10:1), millisecond or picosecond pulsed lasers are typically used, machining the deep hole layer by layer; the thermal effect of each pulse is strictly kept near the vaporization threshold to prevent heat diffusion from damaging the hole wall.
5. Layer Four: Additive-Manufacturing-Specific Thermal Effects
A logic completely opposite to cutting—power density 10⁵~10⁶ W/cm², not rapid material removal but layer-by-layer accumulation
SLM (Selective Laser Melting): the stacking art of strictly controlled thermal gradients
If laser cutting is “releasing heat to remove material”, then SLM (Selective Laser Melting) is “controlling heat to add material”—the thermal-effect logic of the two is completely opposite.
Cutting pursues high heat input and fast penetration, while additive manufacturing must strictly control thermal gradients and suppress drastic temperature differences. The reason is simple: additive manufacturing builds layer by layer, and the temperature distribution of each layer affects the metallurgical quality of the next. Excessive thermal gradients will produce:
· Accumulated residual stress → part warping and distortion
· Excessive interlayer temperature gradients → columnar grain growth and texture strengthening
· Overheated melt pool → balling effects and porosity defects
So the process parameter window of SLM is much narrower than that of cutting. Laser power, scanning speed, scan strategy (checkerboard, stripe, spiral), interlayer waiting temperature—every parameter finely regulates the spatial distribution and temporal evolution of the thermal field.
In actual operation, substrate preheating is an important means of controlling thermal gradients—titanium-alloy SLM is usually preheated to 200-300°C, and nickel-based superalloys to above 800°C. The higher the preheating temperature, the smaller the temperature difference between melt pool and substrate and the lower the thermal stress, but energy consumption and cycle cost also rise. Once again, this is where the process engineer must weigh the trade-offs.
6. The Essence: Quantitative Control Boundaries of Thermal Effects
Having covered the application logic of the four layers of thermal effects, let us end with a more fundamental question: what standard must be met to count as professional?
This section will not discuss how to tune parameters (that belongs to hands-on practice); it only gives the quantitative control boundaries of each process—only by knowing where the “line” is can you learn how to “dance on the line”.
| Process | Power density range | Core quantitative metric | Professional acceptance range | In plain words |
|---|---|---|---|---|
| Welding | 10⁵~10⁶ W/cm² | Heat-affected zone (HAZ) width | Carbon steel 0.5-1.5mm Stainless steel ≤1.0mm |
The narrower the HAZ the better; when it widens, the microstructure degrades |
| Cladding | 10⁵~10⁶ W/cm² | Dilution rate | 5%-15% | Below 5% the bond is weak; above 15% the coating is ruined |
| Hardening | 10³~10⁵ W/cm² | Cooling rate / case depth | Cooling rate >10⁴°C/s Case depth 0.1-1.5mm |
Only fast enough cooling forms martensite; choose the case depth per the application |
| Cutting | 10⁶~10⁸ W/cm² | Cut roughness / HAZ width | Ra≤12.5μm Carbon steel 0.5-1.5mm Stainless steel ≤1.0mm | The smoother the cut and the narrower the HAZ, the better the quality |
| 3D printing | 10⁵~10⁶ W/cm² | Interlayer temperature | Typically 200-300°C (depends on the material) |
Stable temperature means low residual stress and little distortion |
These numbers were not made up on a whim; they are boundaries derived backward from extensive process validation and failure analysis. Take welding HAZ as an example: when the HAZ of carbon steel exceeds 1.5mm, the grains in the coarse-grain zone coarsen markedly and impact toughness drops by more than 30%; when cladding dilution exceeds 15%, the wear life of a cobalt-based coating can be cut in half. Behind these numbers are lessons paid for with real money.
Remembering these boundary values is not about memorizing parameters; it is about establishing criteria for judgment—when a new workpiece arrives, you can quickly judge “roughly where the process window lies” instead of fumbling through parameters one by one by trial and error.
7. Conclusion: Master Both Cold and Heat, Apply Heat on Demand
Only by reading the two articles together can you see the full picture of laser processing:
| Previous part: Avoiding heat | This part: Harnessing heat | |
|---|---|---|
| Core logic | Isolate, dissipate, remove heat | Use, control, harness heat |
| Focus | Avoiding thermal defects | Realizing thermal value |
| Typical scenarios | Fine marking, micromachining, glass cutting | Hardening, cladding repair, additive forming |
| Level of craft | Never let heat reach where it should not go | Deliver heat precisely where it is needed |
Top-tier laser processing neither blindly chases “cold processing” nor blindly chases “high power”. Master both cold and heat, apply heat on demand—cool fully where cooling is needed and heat precisely where heat is needed: that is true process freedom.
I hope these two articles help you avoid detours in hands-on practice. Laser processing runs deep, but its underlying logic is not complicated—understand thermal effects, and you have taken hold of the most crucial key.



Leave a Reply