The word “laser” did not exist before 1960; its original source of inspiration was the maser (microwave amplifier). In 1960, scientists discovered that light shares properties similar to microwaves: when a pump source illuminates certain media, the medium emits light in which amplitude, frequency, direction, and polarization are all identical — and this is exactly the process by which laser light is produced.
Pump Source, Laser Medium, Wavelength, and Application Reference Table
| Pump source | Laser medium | Achievable laser wavelengths | Main applications |
|---|---|---|---|
| Xenon lamp, krypton lamp, 808nm LD | Nd:YAG (neodymium-doped yttrium aluminum garnet) | 1064nm (infrared); frequency-doubled 532nm (green); frequency-tripled 355nm (ultraviolet) | Industrial cutting, welding, marking |
| 808nm semiconductor LD | Nd:YVO₄ (neodymium-doped yttrium vanadate) | 1064nm (infrared) | Diode-pumped marking machines, fine spot quality |
| Xenon lamp, semiconductor LD | Nd:Glass (neodymium-doped glass) | 1060–1064nm (infrared) | High-power pulsed lasers, scientific research |
| Semiconductor LD, flash lamp | Ti:Sapphire (titanium-sapphire crystal) | 700–1000nm (continuously tunable) | Ultrafast lasers for research |
| 915nm/976nm LD | Yb-doped (ytterbium) fiber | 1060–1070nm (infrared) | Mainstream industrial fiber cutting and welding machines |
| Semiconductor LD | Er-doped (erbium) fiber | 1550nm (near-infrared) | Optical communications, long-distance sensing |
| Gas-discharge pumping | CO₂ (carbon dioxide gas) | 10.6μm (far-infrared) | Non-metal cutting, engraving |
| Gas-discharge pumping | He-Ne (helium-neon gas) | 632.8nm (red) | Laser pointing, teaching experiments |
| Gas-discharge pumping | Excimer gas (ArF, KrF) | 193nm, 248nm (deep ultraviolet) | Cold processing, lithography, vision correction |
How 1064nm Laser Light Is Produced: A Worked Example
The YAG cutting and welding machines on the factory floor always output a stable, precisely 1064nm infrared beam. The birth of this beam is, in essence, a precision system of “pumping — population inversion — stimulated-emission amplification”.
Step 1: Pumping and population inversion
The xenon lamp, acting as the pump source, emits full-spectrum light; the near-infrared component around 808nm is absorbed by the neodymium ions in the Nd:YAG crystal, exciting electrons from the low energy level to the high one. This breaks the normal state in which “electrons at the low level far outnumber those at the high level”, achieving population inversion — the precondition for laser generation.
Step 2: Stimulated-emission amplification
Electrons cannot stay at the high energy level for long and spontaneously fall back to the low level, releasing 1064nm photons; when such a photon encounters another electron at the high energy level, it stimulates the emission of a completely identical photon, achieving light amplification in which “one becomes two, and two become four”.
Step 3: Resonator mode selection and output
The total reflector and the partial reflector at the two ends of the crystal form the resonator, weeding out light with the wrong direction or impure wavelength and letting only 1064nm light bounce back and forth inside the cavity, amplified continuously; once the light intensity exceeds the threshold, a stable laser beam is output from the partial reflector.
A Water-Pump Analogy: Breaking Light Amplification Down into Scenes You Can Picture
- The Nd:YAG crystal is a channel built along a hillside; the electrons at the low energy level are the water in a pond at the foot of the hill
- The xenon-lamp pump source is a pump with adjustable power; it lifts the water from the foot of the hill (low-level electrons) up to the reservoir on the hilltop (high energy level), achieving “population inversion”
- The hilltop cannot store water, so it flows back down on its own — that is spontaneous emission; stimulated emission is the “guide wave” in the channel that makes all the water rush down the same path
- The total reflector and partial reflector are baffles at the two ends of the channel: the total reflector sends 100% of the water back uphill to keep circulating and building force, while the partial reflector is a baffle with a controllable gap — the size of that gap is the output rate
- The UV filter tube is the filter screen on the pump’s intake pipe, keeping all the sediment in the water — that is, the ultraviolet light emitted by the xenon lamp — outside
Source: WeChat official account “Soar Laser Parts”



Leave a Reply