Description
Product Overview
The PF05-03-M03 is the unprotected gold mirror: the same Ø12.7 mm fused silica disc, 6.0 mm thick, with a bare gold film and nothing deposited on top of it. Average reflectance is above 97% from 800 nm to 20 µm, one point higher than the protected version, because there is no dielectric layer absorbing part of the beam. Figure is λ/10 peak to valley at 633 nm, polish is 40-20 scratch-dig, parallelism is inside 3 arcmin, clear aperture is 90% of the diameter, and the part number is engraved on the back.
The question every buyer asks is why anyone would accept a surface that cannot be wiped. There are three answers, and all three are technical. The first is reflectance: the overcoat on a protected gold mirror absorbs a little, and in the mid and far infrared that absorption is exactly what separates 97% from 96%. The second is polarization: Thorlabs states that the overcoat of its protected gold mirrors produces polarization changes that are difficult to quantify, and in an interferometer or a polarimetric measurement an unquantified change is worse than a known loss. The third is dispersion: an overcoat is a thin film, a thin film has dispersion, and for femtosecond pulses dispersion means chirp. Bare gold has no such layer, which is why Thorlabs lists polarization-sensitive and ultrafast work as the target applications for this coating.
What those three advantages ask in return is handling discipline, and the discipline is not optional. Bare gold does not oxidise in air, so the film is chemically stable, but it is soft. Thorlabs is explicit about what damages it: fingerprints, aerosols, and the slightest contact with any abrasive material. The published instruction is to handle the optic only when necessary, always by the sides, with latex gloves or equivalent, and to make no attempt to clean the surface other than blowing off dust with clean, dry air or nitrogen. That is not a conservative reading of the datasheet, it is the datasheet. A mirror that will be touched, wiped, or used near an aerosol source should be the protected version instead.
The laser ratings look better than the protected gold part and, on a like-for-like reading, they are: 4 J/cm² at 10.6 µm for 100 ns pulses at 1 Hz over Ø0.435 mm, and 1000 W/cm CW at 10.6 µm over Ø1.18 mm. Both are quoted at 10.6 µm, whereas the -M01 figures are quoted at 1.064 µm for the pulsed case and at both 1.070 µm and 10.6 µm for CW, and the test spot sizes differ as well, so the two tables should not be read as a straight ranking. What can be said without qualification is that at 10.6 µm this film carries the higher CW figure of the two gold coatings, which is why unprotected gold is the film behind CO2 laser line mirrors.
The band starts at 800 nm like the protected version, so this is not a visible or ultraviolet mirror. The same coating is sold in Ø1 inch and Ø2 inch rounds, in three square sizes, and as a 10-piece pack (PF05-03-M03-10) for builds that consume several.
Key Features
- Bare gold, no overcoat: average reflectance above 97% from 800 nm to 20 µm, a point higher than the protected gold coating on the same substrate
- No dielectric layer, so no overcoat absorption in the mid and far infrared where the protected coating loses its point
- No overcoat dispersion: the choice when femtosecond or picosecond pulses must not pick up chirp from a fold mirror
- No unquantified polarization change from an interference layer at oblique incidence
- Figure and finish: λ/10 at 633 nm, 40-20 scratch-dig, parallelism inside 3 arcmin, clear aperture 90% of the diameter
- Ratings at 10.6 µm: 4 J/cm² for 100 ns pulses at 1 Hz over Ø0.435 mm, and 1000 W/cm CW over Ø1.18 mm
- Handling rule: blow off dust with clean dry air or nitrogen only, hold by the edges with gloves, no wiping and no solvents
- Mechanical envelope: 12.7 mm diameter on a 6.0 mm fused silica substrate, tolerances +0.0 / -0.1 mm and ±0.2 mm, part number engraved on the back
Technical Specifications
| Parameter | Value |
|---|---|
| Model | PF05-03-M03 |
| Coating | Unprotected gold, no overcoat |
| Wavelength range | 800 nm – 20 µm |
| Average reflectance | above 97% from 800 nm to 20 µm |
| Substrate | Fused silica |
| Diameter | 12.7 mm (Ø1/2 inch) |
| Diameter tolerance | +0.0 mm / -0.1 mm |
| Thickness | 6.0 mm (0.24 inch) |
| Thickness tolerance | ±0.2 mm |
| Front surface flatness | λ/10 peak to valley at 633 nm |
| Surface quality | 40-20 scratch-dig |
| Parallelism | inside 3 arcmin |
| Clear aperture | 90% of the diameter |
| Damage threshold, pulsed | 4 J/cm² at 10.6 µm, 100 ns, 1 Hz, Ø0.435 mm |
| Damage threshold, CW | 1000 W/cm at 10.6 µm, Ø1.18 mm |
| Cleaning | Blow off dust with clean, dry air or nitrogen only; no other cleaning method |
| Source | Thorlabs official series specification table |
Applications
Unprotected gold is specified where the optic will never be touched and where a dielectric layer would give up something that matters.
- CO2 laser beam paths: at 10.6 µm this film carries the higher CW rating of the gold coatings, for folding a beam into a marking or drilling head
- Ultrafast mid-infrared generation: difference-frequency and OPA outputs where a fold mirror must not add dispersion to a compressed pulse
- Polarization-sensitive interferometry: no overcoat means no unquantified polarization rotation when the mirror is used off normal incidence
- Far-infrared and terahertz benches: where an overcoat would absorb part of the band that the specification is meant to cover
- Sealed instruments and clean rooms: an optic installed once behind a window never needs the handling discipline, and the extra point of reflectance comes free
- High-reflectance reference surfaces: 97% across 800 nm to 20 µm as a calibration fold in a reflectometry setup
Selection Guide
The decision between the three gold coatings on this substrate comes down to two questions: does the beam reach below 2 µm, and will the optic ever be touched.
| Part number | Band | Average reflectance | Overcoat | Wipeable |
|---|---|---|---|---|
| PF05-03-M01 | 800 nm – 20 µm | over 96% | Dielectric | Yes |
| PF05-03-M02 | 2 µm – 20 µm | over 98% | Dielectric, MIL-C-48497A | Yes |
| PF05-03-M03 | 800 nm – 20 µm | over 97% | None | No |
Choose this part only when the answer to the second question is no. If the mirror will be handled, cleaned or exposed to an aerosol, the PF05-03-M01 is the specification to use, and the one point of reflectance it gives up is the smallest insurance premium on the page. If the beam stops at 2 µm and never goes below it, the PF05-03-M02 is two points higher and just as robust. Where the band is visible rather than infrared, the protected aluminum PF05-03-G01 covers 450 nm to 20 µm, and the Ø7.0 mm protected silver mirror is the highest-reflectance option in the visible and near infrared for the small aperture.
FAQ
Can the unprotected gold surface be cleaned at all? No. Thorlabs states that no attempt should be made to clean the surface other than blowing off dust with clean, dry air or nitrogen, and that any other method may damage it. No solvent, no lens tissue, no drag method, no ultrasonic bath.
Will the gold tarnish or oxidise over time? Gold does not oxidise in air, so the film does not degrade the way silver does. The failure mode is mechanical: fingerprints, aerosol droplets and any contact with an abrasive. An optic that is installed and left alone has no shelf-life problem; one that is handled repeatedly does.
Why does this mirror reflect more than the protected gold version? Because there is no overcoat. Thorlabs states that unprotected gold offers higher reflectance than protected gold, and that the overcoat can introduce absorption in the mid to far infrared. The one-point difference in the published figures is that absorption.
Is it suitable for femtosecond pulses? Yes, and that is one of the two reasons Thorlabs names for the coating. With no dielectric layer there is no overcoat dispersion to add chirp to a compressed pulse.
Can I use it at 1064 nm? 1064 nm is inside the 800 nm to 20 µm band, so the reflectance specification covers it. Note, however, that the published damage ratings are given at 10.6 µm, so a 1064 nm application has to be assessed on beam size and pulse duration rather than read off the table; send us the numbers and we will check them.
How do I hold it without damaging the edge? By the sides, with gloves, and only when necessary. The coated face is never touched, and the part is returned to its container as soon as it is out of the mount.
Disclaimer
Specifications shown here are transcribed from the Thorlabs unprotected gold specification table for selection purposes. The official datasheet in force at the time of purchase governs, and Thorlabs may revise figures, marking or packaging without notice. Handling requirements are quoted from the manufacturer and are not optional; damage caused by cleaning or contact is not a manufacturing defect. Commercial terms and lead time are quoted by our sales team against live stock.
Contact Us
Changsha Soar Laser Equipment Co., Ltd. supplies genuine Thorlabs optics to laboratories and machine builders in China. Because this coating cannot be cleaned, it is worth a short conversation before it is specified: send the wavelength, the pulse duration if the source is pulsed, and a description of where the mirror sits in the system, and we will say plainly whether unprotected gold is the right film or whether the protected PF05-03-M01 should carry the risk instead. Hotline +86 159 2722 0467, email 859818709@qq.com, website www.soar-laser.cn.









Reviews
There are no reviews yet.