QQ: 859818709

Thorlabs PF1011-M01 Ø25.4 mm (1 in) Zerodur® Protected Gold Mirror, 800 nm – 20 µm

Thorlabs PF1011-M01 Ø25.4 mm (1 in) Zerodur® Protected Gold Mirror, 800 nm – 20 µm

Price on request
Category:

Description

Product Overview

The PF1011-M01 puts protected gold on a 25.4 mm (1 inch) Zerodur® disc: a gold film with a dielectric overcoat, specified at 96% average reflectance from 800 nm to 20 µm. The body is 6.0 mm (0.24 in) thick to within plus or minus 0.2 mm, figured to lambda/10 peak to valley at 632.8 nm, polished to 40-20 scratch-dig, parallel to within 3 arcmin, with a clear aperture of 90% of the diameter (Ø22.9 mm) and a fine-ground back face that carries the item number. Zerodur® is a registered trademark of Schott; the glass-ceramic holds 0 plus or minus 0.100 x 10-6/°C, against 0.55 x 10-6/°C for fused silica.

This part exists for two fears that arrive together on any infrared power bench. The first is that the coating burns: a fold mirror in a CO2 delivery path sees the full power of the source at a spot size set by the rest of the optics, and a dielectric stack tuned for 10.6 µm is far more fragile there than a metal film. The second fear is quieter and often more expensive – that the mirror survives but the focus moves. A mirror that absorbs a few percent of a kilowatt heats up, the substrate expands, the radius of curvature changes, and the focal point of a cutting head walks out of the kerf over the course of a shift.

Gold answers the first fear because it is a metal: 96% average across 800 nm to 20 µm, essentially flat from one end of the band to the other, and insensitive to angle of incidence in a way that multilayer dielectric coatings are not. A dielectric coating is a resonant structure; its band edge shifts with angle, so a mirror specified at 45 degrees is a different optic at 30 degrees. A metal film reflects because of its free electron density, so the same part works at normal incidence and at 45 degrees without a redesign.

Zerodur® answers the second fear, and this is where the 25 mm format matters more than it does on a small optic. A 25.4 mm disc has four times the area of a 12.7 mm disc, so at the same irradiance it absorbs four times the power: at 4% absorption a 100 W beam deposits about 4 W into the part instead of about 1 W. Zerodur does not remove that heat, it removes the substrate contribution to the resulting movement. The thermal chain is absorption, temperature rise, expansion, curvature change, focal shift; a coefficient of thermal expansion near zero breaks the chain at the second link. What remains is coating stress and mount expansion, both of which are the mount designer’s problem rather than the optic’s.

The overcoat is what makes the part serviceable, and it also has a documented cost that should not be buried. Thorlabs states that the protective dielectric layer on its protected gold mirrors produces polarization changes that can be difficult to quantify, and that the layer sometimes induces absorption in the mid- to far-infrared. If the polarization state at the mirror has to be strictly preserved, or if the last few percent of throughput at 10 µm matter more than cleanability, the correct part is the unprotected gold -M03 on the same body. Choosing -M01 means accepting an unquantified polarization effect in exchange for a film that can be wiped.

The band edge is honest and absolute: below 800 nm this coating has no specification, so a red alignment laser will not be reflected usefully and cannot be used to steer the path. That is the one thing gold cannot do, and it is why infrared benches usually carry a protected aluminum or protected silver mirror somewhere for alignment.

Key Features

  • 96% average from 800 nm to 20 µm: a flat metal response across the near, mid and far infrared, with no band edge to tune and no angle-dependent shift
  • Zerodur® body at 0 plus or minus 0.100 x 10-6/°C: removes the substrate term from the thermal drift budget on a 25 mm disc that absorbs four times the power of a half-inch part
  • Dielectric overcoat: protects a soft metal film so the optic can be cleaned and shared, which is what production benches actually need
  • Insensitive to angle of incidence: the same part number serves normal-incidence and 45 degree folding, unlike a resonant dielectric coating
  • High pulsed and CW ratings: 2 J/cm2 at 1064 nm pulsed and 500 to 750 W/cm continuous, published by Thorlabs for this coating
  • Lambda/10 figure, 40-20 polish, 3 arcmin parallelism: adequate for focal delivery and for imaging paths where wavefront error adds to the system budget

Technical Specifications

Parameter Value
Item Number PF1011-M01
Coating Protected Gold (gold film plus dielectric overcoat)
Wavelength Range 800 nm to 20 µm
Average Reflectance 96% from 800 nm to 20 µm
Substrate Zerodur® glass-ceramic (registered trademark of Schott)
Diameter 25.4 mm (1 in), +0.0 / -0.1 mm
Thickness 6.0 mm (0.24 in), plus or minus 0.2 mm
Clear Aperture 90% of the diameter, Ø22.9 mm
Front Surface Flatness lambda/10 peak to valley at 632.8 nm
Surface Quality 40-20 scratch-dig
Parallelism 3 arcmin maximum
Coefficient of Thermal Expansion 0 plus or minus 0.100 x 10-6/°C (fused silica for comparison: 0.55 x 10-6/°C)
Back Surface Fine ground, item number engraved
Pulsed Damage Threshold 2 J/cm2 at 1.064 µm, 10 ns, 10 Hz, over a 1.000 mm beam
CW Damage Threshold 500 W/cm at 1.070 µm over 0.089 mm; 750 W/cm at 10.6 µm over 0.339 mm
Polarization Overcoat introduces a polarization change that is not quantified by the manufacturer

The pulsed rating of 2 J/cm2 over a 1.000 mm spot is 15.7 mJ per pulse, four times the figure for protected aluminum on the same substrate – the difference between a fold that still has margin at the output of a 1 µm amplifier and one that is running at its limit. The two continuous rows are linear ratings, power divided by beam diameter, quoted at the test spot sizes Thorlabs used; they are coating-level limits measured on a bench, and your duty cycle, spot shape and surface contamination will decide the real number.

The polarization row is not a defect, it is a documented trade. A dielectric layer over a metal is a thin-film interference structure, and interference structures act differently on s and p polarization. Thorlabs does not publish a number for it, which is precisely why applications that care about polarization should not use this coating and should use -M03 instead.

Applications

  • CO2 laser delivery and cutting heads: 10.6 µm fold mirrors where a dielectric coating would be the weak element and where a 750 W/cm continuous rating is needed
  • 1 µm high-power fibre laser gantries: the last two folds before the process head, where 2 J/cm2 pulsed headroom and a cleanable surface both matter
  • Thermal imaging and boresight paths: 3 to 12 µm optics that must survive being handled and focused without a cleanroom ritual
  • Mid-infrared spectroscopy: FTIR beam relays and gas-cell optics where a flat 96% response across two decades of wavelength removes the need for a wavelength-specific coating
  • Production machines with shared tooling: multiple operators, periodic alcohol cleaning, and no realistic way to keep a bare metal film pristine

Selection Guide

Work down this list; each question eliminates a different coating.

  1. Is every wavelength above 800 nm? If any part of the path is visible, this coating cannot serve it and protected aluminum or protected silver has to carry that leg.
  2. Does the polarization state have to be preserved? If yes, stop here and take unprotected gold -M03; the overcoat on this part introduces an unquantified polarization change.
  3. Will the optic be cleaned by other people? If yes, the overcoat is worth more than the one percentage point of reflectance it costs against -M03.
  4. Is the continuous load near the published rating? Check 500 W/cm at 1.07 µm or 750 W/cm at 10.6 µm against your beam diameter, then derate for contamination and duty cycle.
  5. Does focal stability over a shift matter? If the mirror sits before a focusing head on a hot frame, the Zerodur body is the reason to pick this part rather than a fused silica equivalent.

Series Comparison

The four coatings below share one substrate: 25.4 mm diameter, 6.0 mm thick, lambda/10 figure, 40-20 polish, 3 arcmin parallelism, 90% clear aperture. Reflectance and survivability are the only variables.

Coating Wavelength Range Average Reflectance Where It Wins
-G01 Protected Aluminum 450 nm to 20 µm 90% / 95% Visible through far infrared in one coating, most humidity tolerant
-M01 Protected Gold 800 nm to 20 µm 96% Infrared power folding with a cleanable surface, flat response
-M03 Unprotected Gold 800 nm to 20 µm 97% Ultrafast pulses, strict polarization purity, highest infrared reflectance
-P01 Protected Silver 450 nm to 20 µm 97% / 95% Maximum visible and near-infrared throughput

Between -M01 and -M03 the choice is one of discipline rather than optics: one point of reflectance and a cleaner polarization state in exchange for a surface that cannot be touched. Between -M01 and -P01 the choice is wavelength: silver is brighter from 450 nm to 2 µm, gold is flat and one point brighter from 2 µm to 20 µm.

FAQ

Does the protective overcoat change the polarization state?

Yes, and Thorlabs says so directly: the dielectric layer on its protected gold mirrors produces polarization changes that can be difficult to quantify. A thin-film stack acts differently on s and p polarization, and no single number describes the effect across a band. If the polarization at the mirror has to be preserved – a polarization-maintaining delivery fibre, an ellipsometer, an interferometer with a polarized reference – use the unprotected gold -M03 on the same body instead.

Gold or silver for a 1 µm beam?

On reflectance alone they are within a point of each other: 96% for gold from 800 nm to 20 µm, 97% for silver from 450 nm to 2 µm. What separates them is everything else. Silver tarnishes and is the more delicate film; gold is flat all the way to 20 µm and is insensitive to angle. For a 1 µm power path in a working environment, gold is the coating that survives, and one point of reflectance rarely decides a process.

Can this mirror be cleaned?

Yes – the overcoat is the whole point of choosing protected gold over bare gold. Blow off loose dust, then one wet drag wipe with reagent-grade solvent and a lens tissue, then stop. Do not scrub, and do not dry-wipe a surface that may carry grit.

Why Zerodur rather than a copper mirror?

Copper mirrors belong to the regime where the absorbed power is measured in hundreds of watts and the optic is actively water-cooled as part of the head design. This is a passive 25.4 mm optic for benches and delivery paths where the load is a few watts. In that regime the problem is not surviving the heat but not moving while it is there, and a glass-ceramic with a coefficient of thermal expansion near zero solves the second problem without a coolant circuit.

How much of the beam is actually absorbed?

Four percent, on average, over the specified band. At 100 W that is about 4 W deposited in a 25.4 mm disc, which is enough to warm the part and, on an ordinary substrate, enough to move the focus. Zerodur does not remove the 4 W; it removes the expansion that the 4 W would otherwise cause.

Can I align the path with a red laser through this mirror?

No. Below 800 nm gold has no reflectance specification and reflects too little red light to align off reliably. Infrared benches normally keep one protected aluminum or protected silver mirror in the chain for visible alignment, or use an infrared viewer.

What angle of incidence is it specified for?

The coating is a metal film, so its reflectance does not shift with angle the way a resonant dielectric stack does, and the part is used at normal incidence and at 45 degree folding in the same product family. Very high angles of incidence will still change the s and p reflectance split, so confirm the geometry if your design runs beyond 45 degrees.

Usage Precautions

  • Handle by the rim with gloves: a fingerprint on a gold film is a localised absorber and, under power, a localised failure point that the overcoat cannot protect against.
  • Clean wet and once: blow first, one drag wipe, stop. Repeated wiping of the same area thins the overcoat and produces a reflectance dip that looks like contamination.
  • Do not over-clamp: a 25.4 mm disc in an over-tightened retaining ring bends, and the resulting astigmatism is indistinguishable from a bad figure when the beam is focused.
  • Keep the beam inside Ø22.9 mm: the clear aperture is 90% of the diameter, and edge scatter at 10.6 µm is both a loss and a stray-light hazard.
  • Derate the continuous rating for real conditions: 500 W/cm at 1.07 µm and 750 W/cm at 10.6 µm are clean-bench figures. Dust, spatter and fingerprints lower them, so leave margin on a production machine.
  • Do not use it for sub-picosecond pulses: the overcoat is the element that fails first at femtosecond fluences. For ultrashort work, use the bare gold version of the same body.
  • Store dry and covered: gold does not oxidise, but the overcoat and the mount interface both collect dust, and dust on a 10.6 µm fold is a burn-in waiting to happen.

Disclaimer

Specifications on this page are transcribed from Thorlabs official public documentation and are provided for selection reference only; the current official specification sheet governs. Thorlabs may change coatings, tolerances and appearance without notice. Reflectance is quoted as an average across 800 nm to 20 µm. The polarization behaviour of the overcoat is not quantified by the manufacturer and should be measured if it matters to the system. Prices, stock and delivery times are confirmed by our sales team at the time of order, and nothing on this page is a binding offer.

Contact Us

Gaofei Laser supplies genuine Thorlabs stock and quotes this item with current availability, lead time and volume pricing. Send the item number, quantity, wavelength and continuous power, and we will confirm whether protected gold is right for your path or whether the bare gold version serves you better.

  • Sales hotline: +86 159 2722 0467
  • Email: 859818709@qq.com
  • Website: www.soar-laser.cn
  • Company: Gaofei Laser, soar-laser.cn

Reviews

There are no reviews yet.

Be the first to review “Thorlabs PF1011-M01 Ø25.4 mm (1 in) Zerodur® Protected Gold Mirror, 800 nm – 20 µm”

Your email address will not be published. Required fields are marked *

中文EN