QQ: 859818709

Depth of Focus Calculator

Depth of Focus Calculator

🎯 Depth of Focus (Depth of Field) DOF Calculator

Online Depth of Focus (Depth of Field) DOF Calculator

After a laser is focused, depth of focus is the axial distance over which the beam maintains an approximately minimum spot near the focus. Enter the wavelength and f-number (or numerical aperture N.A.) to instantly calculate the diffraction-limited total depth of focus, the one-sided depth of focus and the reference focal spot diameter, for evaluating cutting/welding thickness and judging focal tolerance.

DOF = 2·λ·(F/#)²
NA form: λ / (2·NA²)
Diffraction limit · paraxial approximation in air
🎯
Total depth of focus (f-number form)
DOF = 2λF²
Total length on both sides of the focus
Total depth of focus (NA form)
DOF = λ/(2NA²)
In air, NA = 1/(2F)
Related output: reference Airy disc diameter at the focus
d ≈ 2.44 · λ · F/#
Diameter of the first dark ring, evaluated together with the depth of focus

🎯 Depth of Focus Calculator

Choose an input mode, enter the wavelength and f-number / numerical aperture, and the total depth of focus, one-sided depth of focus, equivalent parameters and focal spot diameter are calculated automatically



μm

Laser wavelength, in micrometres (μm)


F/

Effective focal length of the focusing lens ÷ entrance pupil diameter

💡 Quick reference for common wavelengths: 1064 nm fibre =1.064μm| 532 nm green =0.532μm| 355 nm UV =0.355μm | CO₂ = 10.6μm


📊 Calculation results
📏 Total depth of focus DOF (full length)
—
μm
↕️ One-sided depth of focus (one side of the focus)
—
μm
🔭 Equivalent numerical aperture N.A.
—
Dimensionless (air)
⭕ Reference focal spot diameter d
—
μm (Airy disc 2.44λF)

Note: the above is the theoretical depth of focus for a uniform aperture at the diffraction limit; the Rayleigh range of a Gaussian beam, zR= πw₀²/λ, is defined differently; see the formula details below.

Formula details

Definition of the diffraction-limited depth of focus, its two forms of expression and its difference from the Rayleigh range of a Gaussian beam

1
Total depth of focus (full length)
DOFTotal = 2 · λ · (F/#)²
λ: laser wavelength;F/#: f-number of the focusing lens. The total depth of focus is the axial distance on both sides of the focus over which the spot remains approximately minimum (acceptable circle of confusion)combined full length. λ is in the same unit as the result (λ entered in μm, DOF output in μm).
2
One-sided depth of focus
DOFhalf = λ · (F/#)² = DOFtotal / 2
The usable distance you can move from the best focus in either direction. In practical focusing, the workpiece surface is allowed to lie within ±DOF of the focushalfaround the focus, with the spot size and power density still at acceptable levels; therefore the one-sided depth of focus is theaxial focal tolerance。
3
Numerical aperture N.A. form
DOFtotal = λ / (2 · NA²),DOFhalf = λ / (4 · NA²)
Under the paraxial approximation in airNA = 1/(2·F/#), substitution gives the result. The larger the NA (greater convergence angle, more ‘aggressive’ focusing), the more the depth of focus shortens withthe inverse square of NAsharply — the focus of a high-NA objective is very ‘thin’.
4
Difference from the Rayleigh range of a Gaussian beam
zR = π · w₀² / λ
The Rayleigh range is based on the Gaussian beam1/e² intensity radius w₀(where the spot area doubles); the diffraction depth of focus is based on the uniform-apertureAiry disc / acceptable circle of confusion. The two are defined differently, and the conversion factor differs by roughly a factor of π/4 (about 0.8~1.3 times, depending on whether w₀ is taken as the 1/e² radius or the radius of the first dark ring of the Airy disc),so the values cannot be interchanged directly。
5
Reference focal spot diameter (related quantity)
d ≈ 2.44 · λ · F/#
Diameter of the first dark ring of the Airy disc. Depth of focus and spot size must be considered together: as the f-number increases, the depth of focus grows withF²while the spot diameter grows only withFlinearly — a long depth of focus is bought at the price of a larger focus and lower power density.
6
Engineering significance of focal tolerance
ΔzTolerance ≈ ± λ · (F/#)²
Depth of focus directly determines: ① the range of uniform energy along the kerf/weld in the thickness direction of the workpiece; ② the accuracy requirements for Z-axis positioning and autofocus; ③ process tolerance when the material is warped or the sheet thickness is uneven. The shallower the depth of focus, the higher the demands on fixturing and follow-focus.

Parameter details

Meaning and values of the three core parameters: wavelength, f-number / N.A. and depth of focus

🌈

Wavelength λ

lambda

The wavelength of the laser, which determines the diffraction scale. This tool uses μm throughout (1 μm = 1000 nm).

Common unit: μm (micrometre)

  • Fibre laser 1064 nm = 1.064 μm
  • Green light 532 nm = 0.532 μm
  • UV 355 nm = 0.355 μm
  • CO₂ laser 10.6 μm
  • Depth of focus and wavelengthdirectly proportional: doubling the wavelength doubles the depth of focus
🔭

F-number / numerical aperture

F/# · N.A.

Two equivalent ways of describing the converging power of a focusing lens; in air, NA = 1/(2·F/#).

Dimensionless

  • F/# = focal length f ÷ entrance pupil diameter D
  • Common f-theta field lenses: F/2 ~ F/8
  • Smaller f-number → smaller spot and higher power density
  • Depth of focus and (F/#)²directly proportional, and with NA² it isinversely proportional
  • Doubling the f-number: spot diameter ×2, depth of focus ×4
📏

Depth of focus DOF

Depth of Focus

The axial range near the focus over which the spot remains approximately minimum, divided into total depth of focus (full length) and one-sided depth of focus.

Common unit: μm; convert to mm for larger values

  • Total depth of focus = 2λ(F/#)² (combined on both sides of the focus)
  • One-sided depth of focus = λ(F/#)² (≈ focal positioning tolerance)
  • 1064 nm + F/2.8: total depth of focus ≈ 16.7 μm
  • CO₂ 10.6 μm + F/5: total depth of focus ≈ 530 μm
  • is adiffraction-limited theoretical value, but in practice it is also affected by aberration and beam quality M²

📋 Quick-reference table of total depth of focus (wavelength × f-number)

The table gives the total depth of focus DOF = 2·λ·(F/#)² in μm; the one-sided depth of focus is half of the tabulated value

Wavelength λ F/2 F/2.8 F/4 F/5.6 F/8
0.355μm(355 nm UV) 2.84 5.57 11.36 22.27 45.44
0.532μm(532 nm green) 4.26 8.34 17.02 33.37 68.10
1.064μm(1064 nm fibre) 8.51 16.68 34.05 66.73 136.19
10.6μm(CO₂) 84.80 166.21 339.20 664.83 1356.80(≈1.357mm)

Table example: a 1064 nm fibre laser with an F/2.8 field lens gives a total depth of focus of 16.68 μm and about 8.34 μm on one side; switching to an F/8 field lens at the same wavelength increases the total depth of focus to 136.19 μm, but the focal spot diameter also grows from about 7.27 μm to about 20.77 μm.

⚠️ Common pitfalls and notes

Six most common pitfalls when using the depth-of-focus formula for process decisions

Is diffraction depth of focus the same as the Gaussian beam Rayleigh range?

No. The Rayleigh range zR= πw₀²/λ is based on the 1/e² intensity beam-waist radius, while the depth-of-focus formula is based on the Airy disc blur of a uniform aperture; the two have different definitions and criteria, and their values differ by a factor on the order of π/4, so they cannot be interchanged directly. For Gaussian beam analysis, please use the Gaussian Beam Calculator.

If the f-number doubles, does the depth of focus also double?

Wrong — it isquadrupled. Depth of focus is proportional to (F/#)²: changing from F/2.8 to F/5.6 (2×) increases the depth of focus by about ×4, while the spot diameter only goes ×2. The squared relationship is the most commonly overlooked term in depth-of-focus estimation.

Does wavelength have little effect on depth of focus?

Depth of focus and wavelengthdirectly proportional. At the same F/5 focusing, the depth of focus of a 10.6 μm CO₂ laser (530 μm) is fully 10 times that of a 1.064 μm fibre laser (53.2 μm). This is why CO₂ lasers naturally have an advantage in depth of focus for thick-plate processing.

Should the NA form be written λ/(2·NA)?

The denominator isNA²not NA: DOF = λ/(2·NA²), one-sided = λ/(4·NA²). Raising NA from 0.1 to 0.2 does not halve the depth of focus but reduces it to 1/4. The inverse-square relationship in the NA form is very easy to write incorrectly.

Is a larger depth of focus always better?

Not necessarily. Depth of focus is obtained by increasing the f-number (reducing NA), but the focal spot d ≈ 2.44λF grows at the same time and the power density falls. Precision cutting/micromachining of thin sheet needs a small spot and high power density, so a shallow depth of focus plus precision follow-focus is preferred; depth of focus is prioritised only for thick-plate processing.

Can the sheet thickness be equal to one depth of focus?

They cannot be equated directly. Depth of focus is only the ‘approximately minimum spot’opticalrange; in practice, kerf/weld formation is also affected by heat conduction, material absorptivity, assist gas, cutting speed and defocus strategy (positive/negative defocus). Depth of focus is a necessary reference, not an upper limit on the processable thickness.

💡 Common applications

✂️
Laser cutting: precision cutting of thin sheet vs stable cutting of thick plate
For high-speed precision cutting of thin sheet, choose a small-f-number field lens (around F/2), trading a small spot and high power density for kerf width and speed; thick-plate cutting requires a larger depth of focus to keep the energy consistent at the upper and lower edges of the cut, so an F/4~F/8 field lens is usually chosen together with a positive/negative defocus process.
🔩
Laser welding: defocus and weld penetration
In deep-penetration welding the defocus must lie within the one-sided depth of focus; otherwise the power density at the weld spot drops below the threshold and the penetration changes abruptly. Estimating the depth of focus helps determine the Z-axis setting of the welding head, the joint-gap tolerance and the flatness requirement of the workpiece.
🎯
Alignment and autofocus accuracy assessment
The one-sided depth of focus is the axial focal positioning tolerance: only about ±8.3 μm for 1064 nm + F/2.8, requiring capacitive/laser follow heads with micron-level response; whereas CO₂ + F/8 can reach about ±0.68 mm, which ordinary lifting mechanisms can tolerate.

📋 Frequently asked questions

Q: Are depth of focus and depth of field the same thing?
In strict optical definitions, depth of field refers to the axial range on the object side that can be imaged sharply, while depth of focus refers to the corresponding range on the image side (focal side). The laser processing industry usually does not distinguish object and image sides; colloquially both refer to the axial distance near the focus over which the spot is approximately minimum. This calculator computes precisely this image-side depth of focus.
Q: Why, with the same field lens, is the depth of focus of a CO₂ laser so much larger than that of a fibre laser?
Because depth of focus is directly proportional to wavelength. The CO₂ wavelength of 10.6 μm is 10 times the fibre wavelength of 1.064 μm, so at the same f-number the depth of focus is exactly 10 times larger; the price is that the diffraction spot is also 10 times larger, making fine processing inferior to short-wavelength lasers.
Q: Why does the calculated depth of focus not match actual processing?
The formula gives the theoretical value for an ideal uniform aperture, diffraction limit and M²=1. Real systems have beam quality M²>1, field-lens aberration, thermal lensing in the optical path, etc.; the effective depth of focus usually needs to be corrected by roughly a factor of M². Adding material thermal effects, the measured usable range will differ from the theoretical value.
Q: When selecting, should I choose an F/2.8 or an F/8 field lens?
It depends on the process trade-off: F/2.8 gives a small spot and high power density, suitable for precision cutting of thin sheet, marking and micro-welding, but the depth of focus is shallow (about 16.7 μm at 1064 nm) and demands high follow-focus accuracy; F/8 has a deep depth of focus (about 136 μm) and a high tolerance to sheet-thickness variation, suitable for thick-plate cutting, but the spot is larger and the maximum speed lower. You can use this tool together with the Focused Spot Size Calculator for a quantitative comparison.

中文EN