QQ: 859818709

Lens Weight Calculator

Lens Weight Calculator

⚖️ Lens Weight Calculator

Lens Weight Calculator

Based on the lens diameter, centre thickness, radius of curvature and material density, this tool accurately calculates the sag, volume and weight of a spherical lens. It uses a complete physical model that adds material for convex surfaces and subtracts it for concave surfaces.

⚖️
Spherical sag
sag = |R|−√(R²−r²)
R radius of curvature, r semi-aperture
Spherical cap volume
V = πh²(3R−h)/3
h sag, R radius of curvature
Lens weight
W = (Vcyl + ΣVcap) × ρ
Cylinder volume + convex/concave correction × material density

⚖️ Lens Weight Calculator

Enter the lens geometry parameters and material density to calculate the sag, volume and weight automatically


mm

Lens outer diameter (clear aperture)


mm

Axial thickness at the centre of the lens


mm

Positive = convex, negative = concave


mm

Positive = convex, negative = concave; enter 1e9 for a flat surface


g/cm³

Click a preset below to fill in with one click










📊 Calculation results
📐 Front surface sag sag₁
—
mm
📐 Rear surface sag sag₂
—
mm
📦 Total lens volume V
—
mm³
⚖️ Lens weight W
—
grams

Formula details

Complete physical derivation of spherical lens weight: from sag to spherical cap volume, and then to total weight

① Spherical sag formula
sag = |R| − √(R² − (D/2)²)
R: radius of curvature (mm),D: lens diameter (mm). Sag is the axial distance from the vertex of the spherical surface to the edge plane. The larger |R|, the smaller the sag (the flatter the surface).
② Spherical cap volume formula
Vcap = π·h²·(3|R| − h) / 3
h= sag,Ris the radius of curvature. A spherical cap is the portion cut from a sphere by a plane. A convex surface (R>0) adds material, a concave surface (R<0) removes material.
③ Basic cylinder volume
Vcyl = π·(D/2)²·CT
Treat the lens as a cylinder of uniform thickness:Dis the diameter,CTis the centre thickness. This is the approximate volume without taking surface curvature into account; in practice the spherical cap correction must be added / subtracted.
④ Total material volume (sign convention)
Vtotal = Vcyl + Σ Vcap,signed
Front surfaceR₁>0 (convex)bulges outwards, adding material;R₁<0 (concave)curves inwards, removing material. The rear surface is the opposite:R₂<0 (convex)bulges outwards, adding material;R₂>0 (concave)removes material. Formula: V = Vcyl + sign(R₁)·Vcap1 − sign(R₂)·Vcap2
⑤ Weight = volume × density
W = Vcm³ × ρ
Convert the volume from mm³ to cm³ (÷1000), then multiply by the material density ρ (g/cm³) to obtain the weight (grams). Densities of different materials can differ by up to 74% (e.g. BK7 vs SF11).
⑥ Comparison of densities of common optical materials
Material Density (g/cm³) Type
BK7 crown glass 2.51 Optical glass
Fused silica SiO₂ 2.20 Silica glass
SF11 heavy flint 4.37 High-index glass
Sapphire Al₂O₃ 3.98 Crystal
Calcium fluoride CaF₂ 3.18 Infrared crystal
Silicon Si 2.33 Infrared semiconductor
Germanium Ge 5.32 Infrared semiconductor
PMMA acrylic 1.18 Plastic
PC polycarbonate 1.20 Plastic

Parameter details

Three key parameters affecting lens weight

📏

Lens diameter D

  • Diameter affects volume quadratically (the D² term)
  • Doubling the diameter → roughly quadruples the volume
  • It also affects sag: the larger the diameter, the larger the sag
  • Common sizes: Φ6.35, Φ12.7, Φ25.4, Φ25, Φ50 mm
  • The actual clear aperture may be slightly smaller than the physical outer diameter
🔄

Radius of curvature R

  • Sign convention: R>0 convex (thicker at the centre than at the edge), R<0 concave (thinner at the centre than at the edge)
  • |R|→∞ indicates a flat surface (enter a large number such as 1e9)
  • The smaller |R|, the more strongly curved the surface → the larger the sag
  • Physical constraint: |R| must be > D/2, otherwise the spherical surface does not exist
  • Biconvex lens: R₁>0, R₂<0 (material added on both surfaces)
  • Biconcave lens: R₁<0, R₂>0 (material removed on both surfaces)
⚗️

Material density ρ

  • Density directly determines weight: W = V × ρ
  • BK7 = 2.51 g/cm³ (the most commonly used optical glass)
  • SF11 = 4.37 g/cm³, 74% heavier than BK7
  • Germanium Ge = 5.32 g/cm³, making infrared lenses particularly heavy
  • Plastics (PMMA/PC) are only 1.18~1.20, over 50% lighter

📋 Quick-reference table of common standard lenses (BK7 material)

Reference values of volume and weight for standard lenses made of BK7 (ρ=2.51 g/cm³)

Specification Type R (mm) Volume (mm³) Weight (g)
Φ25 × 3 mm Biconvex ±50 2256.18 5.66
Φ25 × 5 mm Biconvex ±50 3237.92 8.13
Φ50 × 5 mm Biconvex ±100 16085.92 40.38
Φ25.4 × 3 mm Biconvex ±50 2355.63 5.91
Φ25 × 3 mm Plano-convex +50 / ∞ 1864.40 4.68
Φ12.7 × 2 mm Plano-convex +25.4 / ∞ 304.71 1.21 (sapphire)
Φ20 × 6 mm Biconcave ∓80 (SF11) 1687.57 7.37

⚠️ Common misconceptions and cautions

Common mistakes in lens weight calculation

Is the weight of a convex lens = π(D/2)²·CT·ρ?

No! π(D/2)²·CT is only the volume of a uniform-thickness cylinder. The extra spherical cap volume bulging out at a convex surface must also be added (for a biconvex lens, add both caps); for a concave surface it must be subtracted from the cylinder. The complete formula is V = Vcyl + sign(R₁)·Vcap1 − sign(R₂)·Vcap2。

Can a concave surface produce negative weight?

No. A concave surface removes material from the cylinder (subtracting the spherical cap volume), so the final weight is still positive; it is merely lighter than a uniform-thickness cylinder of the same size. A biconcave lens is always lighter than a uniform-thickness cylinder.

Are material densities all about the same?

They differ enormously! BK7 (2.51) and SF11 (4.37) differ by 74%, and germanium Ge (5.32) is 2.1 times BK7. For a lens of the same specification, changing the material can double the weight. Material selection must take the effect of weight on the structure into account.

If the sag is small, can it be ignored?

Although the sag is small (typically 0.5~3mm), the spherical cap volume is proportional to sag², so the cumulative effect cannot be neglected. For a Φ25×5 biconvex lens with R=50, the two caps together contribute about 24% of extra volume.

Ignore the centre thickness tolerance?

The centre thickness CT affects volume directly and linearly. A CT tolerance of ±0.1mm on a Φ25 lens leads to a volume change of about ±50mm³ (about ±0.12g). In high-precision applications the effect of CT tolerance on weight must be assessed.

Can coating weight be neglected?

Usually coatings are indeed very light (<0.1% of total weight), but high-reflection multilayer dielectric coatings (such as 40+ layer HR coatings) can reach several micrometres in cumulative thickness and may need to be considered on large-area optics. Evaluation is recommended for precision inertial systems (such as galvanometer scanners).

💡 Common application scenarios

🔄
Inertia of laser scanning galvanometer mirrors
The weight of galvanometer mirrors / scanning lenses directly affects rotational inertia and acceleration performance. Lightweight design can increase scanning speed and reduce motor load. SF11 is 74% heavier than BK7, so BK7 or fused silica should be preferred for high-speed scanning.
🏗️
Load-bearing of mechanical support structures
In large-aperture optical systems, lens weight determines the load requirements on mounts, alignment stages and support structures. Germanium lenses above Φ50 (infrared systems) can weigh tens of grams, requiring strengthened structural design.
🤖
Robot payload
When a robot end-effector carries a vision / laser module, the weight of every lens affects the payload budget. Plastic lenses (PMMA/PC) are only 1.2 g/cm³ and are the first choice for weight reduction, but temperature resistance and optical performance limits must be kept in mind.

📋 FAQ

Q: Why can’t the cylinder volume formula be used directly to calculate the weight of a convex lens?
The cylinder volume π(D/2)²·CT accounts only for the uniform-thickness cylindrical part. The two spherical surfaces of a convex lens bulge out with extra material (spherical caps); ignoring this makes the weight too low. This tool automatically applies the spherical cap correction to ensure accuracy.
Q: How is the sign of the radius of curvature determined?
Convention: R>0 denotes a convex surface (thicker at the centre than at the edge), R<0 a concave surface (thinner at the centre than at the edge). |R|→∞ is a flat surface (1e9 may be entered in the calculator). Biconvex lens: R₁>0, R₂<0; plano-convex lens: R₁>0, R₂=∞.
Q: What if the calculated result differs from the actual weighed value?
Possible causes: ① the material density deviates from the nominal value (glass batch variation); ② the lens edge has a chamfer / bevel; ③ centre thickness tolerance. Generally a deviation within ±2% between the calculated and measured values is considered normal.
Q: Can this tool also calculate aspheric lenses?
No. This tool applies only to spherical lenses. The sag and volume of an aspheric surface must be calculated with the aspheric equation, with the deviation depending on the aspheric coefficients. For aspherics, please use the Aspheric Sag Calculator.

中文EN