QQ: 859818709

Optical Density and Transmission Calculator

Optical Density and Transmission Calculator

🕶️ Optical Density OD ↔ Transmittance Calculator

Optical Density OD ↔ Transmittance Calculator

Essential for selecting filters, attenuators and laser safety glasses: enter the optical density OD to automatically convert to transmittance T%, blocking rate and attenuation in decibels; supports stacking multiple elements (OD values add) and incident/transmitted power conversion. Remember: every increase of 1 in OD reduces the transmittance to 1/10.

🕶️
OD definition
OD = −lg T
T is the fractional transmittance
Transmittance
T% = 100·10⁻ᴼᴰ
Percentage transmittance
Tenfold rule (OD +1 → transmittance ÷10)
OD 3 → 0.1% OD 6 → 0.0001% OD 7 → 10⁻⁵%
Stacking multiple elements: OD_total = OD₁ + OD₂ + …

🕶️ Optical Density OD ↔ Transmittance Calculator

Mode A: calculate transmittance from OD (supports stacking); Mode B: calculate OD from transmittance; optionally enter incident power to calculate transmitted power automatically


Nominal OD of the filter/protective eyewear, e.g. OD3

Added when several elements are stacked, e.g. add another OD3

If left blank it is taken as 0; transmittances multiply, ODs add


W

When filled in, the transmitted power P_out is calculated automatically


📊 Calculation results
🌑 Total optical density OD
—
Dimensionless (logarithmic)
💡 Transmittance T%
—
T = 10⁻ᴼᴰ
🛡️ Blocking rate (1−T)×100%
—
1 − T
📉 Attenuation
—
dB(= −10·OD)

Formula details

Optical density (OD) is the negative base-10 logarithm of transmittance; understanding this is all you need for the conversions

① Definition of OD (optical density)
OD = −log₁₀ T = −lg T
T: fractional transmittance (0~1, e.g. 0.001 means 0.1%). OD is adimensionless logarithmic value, compressing transmittances spanning many orders of magnitude, from 1 down to 10⁻⁹, which makes it convenient for specifying high-attenuation components.
② OD → transmittance
T = 10⁻ᴼᴰ T% = 100 × 10⁻ᴼᴰ
OD=0 → T=100% (fully transmitting); OD=1 → 10%; OD=3 → 0.1%; OD=6 → 0.0001%.Every increase of 1 in OD reduces the transmittance to 1/10 of its previous value— this is the ‘tenfold rule’.
③ Transmittance → OD (inverse calculation)
OD = −log₁₀ ( T% / 100 )
First divide the percentage transmittance by 100 to obtain a fraction, then take the negative logarithm. Example: T%=50 → OD≈0.301; T%=0.01 (one ten-thousandth) → OD=4.
④ Rule for stacking multiple elements
OD_total = OD₁ + OD₂ + OD₃ + …
When light passes through the elements in sequencetransmittances multiply: T = T₁×T₂×…; after taking logarithms this becomesthe ODs simply add. Example: OD3 + OD3 = OD6 (transmittance 0.1%×0.1%=0.0001%).
⑤ Incident/transmitted power conversion
P_out = P_in × T = P_in × 10⁻ᴼᴰ
P_in: incident power (W);P_out: transmitted power (W). Example: a 100 W laser is reduced to only 0.1 W = 100 mW after an OD3 attenuator. Prerequisite: the material operates in the linear regime and has not been damaged.
⑥ Attenuation in decibels (dB) and blocking rate
Atten(dB) = 10·lg(P_out/P_in) = −10·OD
Decibels and OD differ only by a factor of −10: OD1 = −10 dB, OD6 = −60 dB.Blocking rate(the fraction absorbed/reflected) = (1−T)×100%; OD3 corresponds to 99.9% blocking.

Parameter details

Three core concepts: OD, transmittance and stacking multiple elements

🌑

Optical density OD

  • Dimensionless, OD = −lg T, on a logarithmic scale
  • The larger the OD, the stronger the attenuation; OD=0 means fully transmitting
  • A difference of 1 in OD → a tenfold difference in transmittance; a difference of 3 → a thousandfold
  • Filters commonly range from OD0.1 to OD6; protective eyewear can reach OD7+
  • OD must correspond to a specific wavelength (wavelength selectivity)
💡

Transmittance T / T%

  • Two ways of writing it: T (fraction, 0~1) and T% (0~100%)
  • T% = 100 × 10⁻ᴼᴰ, uniquely determined by OD
  • At high OD, T% is extremely small: OD7 → 10⁻⁵% (one part in a million)
  • Blocking rate = 100% − T%; do not confuse it with transmittance
  • For linear materials, T is independent of the incident power level
🧱

Stacking rule for multiple elements

  • In a serial optical path, transmittances multiply: T=T₁·T₂·T₃
  • Equivalent to adding ODs: OD_total=OD₁+OD₂+OD₃
  • Example: OD3+OD3=OD6 (not OD3, and certainly not OD9)
  • The ODs of the elements can be added directly only if they are specified at the same wavelength
  • Stacking also requires consideration of interface reflections, damage threshold and heat dissipation

📋 OD quick-reference table (OD 0~8)

Transmittance, blocking rate, attenuation in dB and transmitted power for 100 W incident power

OD Transmittance T% Blocking rate Attenuation dB 100 W incident → P_out
0 100% 0% 0 dB 100 W
0.3 50.12% 49.88% −3 dB 50.12 W
0.5 31.62% 68.38% −5 dB 31.62 W
1 10% 90% −10 dB 10 W
2 1% 99% −20 dB 1 W
3 0.1%(10⁻³) 99.9% −30 dB 0.1 W(100 mW)
4 0.01%(10⁻⁴) 99.99% −40 dB 10 mW
5 0.001%(10⁻⁵) 99.999% −50 dB 1 mW
6 10⁻⁴%(0.0001%) 99.9999% −60 dB 100 μW
7 10⁻⁵%(0.00001%) 99.99999% −70 dB 10 μW
8 10⁻⁶%(0.000001%) 99.999999% −80 dB 1 μW

Note: −3 dB corresponds to about 50% transmittance (half-power point); for non-integer OD, T% is likewise calculated as T%=100·10⁻ᴼᴰ. The 100 W column assumes linear attenuation; in actual use the laser-induced damage threshold (LIDT) of the component must not be exceeded.

⚠️ Common pitfalls and notes

Six most common mistakes in OD selection

OD is a linear scale, so OD6 is only twice as strong as OD3?

Wrong. OD is a logarithmic scale: each difference of 1 in OD means a tenfold difference in transmittance. OD6 is 1000 times stronger than OD3 (transmittance 0.0001% versus 0.1%). Treating OD as a linear value is the most common mistake.

Do transmittances add when elements are stacked?

Wrong. In a serial optical path transmittances multiply and ODs add: OD3+OD3=OD6 (T=0.1%×0.1%=0.0001%), by no means 0.1%+0.1%=0.2%, nor OD9.

OD6 = 60% blocking?

A serious error. The transmittance of OD6 is 10⁻⁴%, and the blocking rate is as high as99.9999%(999999 parts per million). There is no direct correspondence between the OD number and the blocking percentage; you must convert using 100·10⁻ᴼᴰ.

Does the nominal OD apply across the whole wavelength range?

No. The OD of laser safety glasses and filters is specified atspecific wavelengths/bands(e.g. 190~400 nm OD7+); outside the protected band it may be almost fully transmitting. When selecting, you must check the OD at your own laser wavelength and the VLT (visible light transmittance).

The higher the incident power, the lower the transmittance?

For linear materials below the damage threshold, the transmittance T is an intrinsic property of the material and is independent of incident power: P_out always equals P_in×T. But once the power density exceeds the LIDT, the material may bleach, ablate or even break down, and the OD fails instantly.

Are dB and OD two unrelated metrics?

They differ only by a fixed factor: Atten(dB) = −10·OD. OD1 = −10 dB, OD3 = −30 dB, OD6 = −60 dB. Fibre communications conventionally use dB, while filters/protective eyewear use OD; after conversion they can be compared directly.

💡 Common applications

🕶️
Laser safety eyewear selection
Back-calculate the required OD from the laser wavelength, maximum incident power and the maximum permissible exposure (MPE) for the eye. For example, to reduce the power entering the eye to the order of 0.1 mW from a 100 W laser requires about OD6 protection; be sure to check the protection wavelength and LIDT at the same time.
🌑
Power control with neutral density (ND) filters
When excessive power saturates a detector or causes over-processing, use an ND filter for precise attenuation. OD0.3 ≈ half the power (−3 dB), OD1 leaves 10%; combining several filters of different OD lets you flexibly achieve the target total OD.
🪞
Evaluation of high-reflection/high-transmission coating specifications
A high-reflection mirror with R=99.9% means a transmittance T=0.1%, i.e. OD3; a high-transmission coating with T=99.5% corresponds to OD≈0.0022. OD allows you to compare intuitively the order-of-magnitude differences in residual transmittance (leakage) between different coating designs.

📋 Frequently asked questions

Q: Why does the transmittance become 1/10 for every increase of 1 in OD?
Because OD is the negative base-10 logarithm: T=10⁻ᴼᴰ. As OD changes from n to n+1, the transmittance goes from 10⁻ⁿ to 10⁻⁽ⁿ⁺¹⁾, exactly a tenfold reduction. This is the ‘tenfold rule’ dictated by the logarithmic definition.
Q: Why does 50% transmittance correspond to OD 0.3 rather than 0.5?
OD=−lg(0.5)≈0.301. Because 10⁻⁰·³≈0.501, this is the origin of the ‘−3 dB half-power point’ in electronics. OD0.5 actually corresponds to a transmittance of 31.62%.
Q: What OD do you get by stacking two OD3 elements?
OD6. After the first element, 0.1% of the light remains; passing through the second multiplies by another 0.001, giving a total transmittance of 0.0001% (10⁻⁴%), i.e. OD6. This assumes both elements are specified at the same wavelength and that intermediate interface reflections are negligible or already included in the nominal values.
Q: Is a sufficiently high OD on safety eyewear guaranteed to be safe?
Not necessarily. The following must also be satisfied: ① the nominal OD band covers your laser wavelength; ② the power/energy density is below the lens LIDT (to prevent breakdown); ③ the transmitted level is below the MPE for the corresponding wavelength and pulse width; ④ the lens is free of scratches and ageing and fits properly. OD only describes the attenuation ratio under normal conditions and does not represent damage resistance.

中文EN