Description
Product Overview
The ZBTK LHP33-FB2-SYS is an ultra-high-power, digital closed-loop welding galvo kit from Shenzhen Zhibotaike Technology Co., Ltd. (ZBTK). Its 33 mm clear aperture is optimised for laser welding and handles up to 12000 W of laser power, and water cooling keeps the optics stable during long high-power operation. Digital closed-loop control with high-resolution encoder feedback delivers sub-microradian positioning accuracy and very low thermal drift, meeting the tight seam-position accuracy and repeatability that precision welding demands. Welding speed reaches up to 2 m/s; paired with collimating lenses (F100/F150) and f-theta lenses (F210/F254/F330), the kit covers a wide range of seam geometries.
Key Features
⚡ High-Speed Welding Scan
Welding scan speed reaches up to 2 m/s with a positioning speed of 6 m/s and a tracking error of only 0.45 ms. The optimised servo control algorithm keeps trajectory accuracy very high even while the mirrors swing at full welding speed, so seam uniformity and consistency are far better than with conventional robotic-arm welding. Fast jumps and very short transition delays shorten the process cycle time and raise line throughput. Continuous seams, spot welds and other welding processes all run stably at high speed.
🎯 High-Precision Positioning
Repeatability (RMS) is under 1 μrad and non-linearity under 0.3 mrad, with position feedback from a high-resolution digital encoder. Closed-loop control removes the drift and hysteresis inherent in open-loop systems: gain drift under 15 ppm/K, zero drift under 10 μrad/K and 8-hour drift under 0.03 mrad (after a 30-minute warm-up). Precision optical sensors and advanced automatic thermal-drift compensation keep positioning stability and process consistency excellent through long continuous runs.
🌡️ Ultra-Low Thermal Drift
Refined photoelectric sensor technology and an advanced automatic thermal-drift compensation algorithm overcome the temperature drift problem of galvo scanners. Zero temperature drift is only under 10 μrad/K, gain temperature drift under 15 ppm/K and 8-hour long-term drift under 0.03 mrad, satisfying the stability requirements of most long-duration, high-volume marking and welding applications. Process quality stays consistent even when ambient temperature swings by ±10 °C.
🔧 High-Torque Permanent-Magnet Galvo Motor
The kit uses ZBTK galvo motors developed specifically for welding, with rotor inertia and torque constant matched by design, so it still achieves 0.45 ms tracking response and 2 m/s welding speed under the load of 33 mm large-aperture mirrors. The motors use high-temperature-resistant materials and an efficient heat-dissipation structure, so performance does not degrade during long high-power operation.
📡 Digital Servo Driver Board
The FB2 digital closed-loop servo driver board integrates a high-speed DSP and high-resolution A/D conversion for real-time encoder acquisition and closed-loop servo regulation. The board provides multiple protection functions, including over-current protection, over-temperature protection and position-deviation alarms, keeping the galvo system safe and reliable under all operating conditions.
🔌 Interface Compatibility
The product supports the XY2-100 and SL2-100 standard communication protocols. SL2-100 gives 20-bit digital resolution (0.76 μrad) and XY2-100 gives 16-bit resolution (12 μrad), and both are compatible with the vast majority of laser controller cards on the market (such as the JCZ EZCAD series, SCANLAB RTC series and RAYLASE SP-ICE series). Integration is plug-and-play and efficient. Power supply requirement is ±15 V / 10 A, and the interface cables are shielded to suppress external electromagnetic interference.
❄️ Efficient Cooling System
The product is water cooled, with the water circuit covering the core heat zones of the mirror mount and the entrance aperture. This controls mirror temperature rise and prevents spot drift and focus shift caused by thermal lensing. Under high-power, long-duration continuous operation the water cooling keeps the galvo at its optimum working temperature and holds process quality consistent.
🛡️ Smart Monitoring and Protection
The welding galvo system carries a complete fault-monitoring and alarm system that detects abnormal power supply, abnormal motor operation, driver board faults, cable connection faults, abnormal core-zone temperature, protective window faults and other conditions in real time. The system can actively cut the laser circuit and notify the welding controller to stop, preventing defective parts from reaching downstream processes and protecting operator safety. The digital closed-loop version also supports encoder signal readback and position-deviation monitoring, further improving system reliability and serviceability.
Detailed Specifications
| Optical Parameters | |
|---|---|
| Clear Aperture | 33 mm |
| Scan Angle | ±0.35 rad |
| Max Laser Power | 12000 W |
| Mirror Coating Wavelength | 1030–1090 nm |
| Scanning Parameters | |
|---|---|
| Non-linearity | under 0.3 mrad |
| Tracking Time | 0.45 ms |
| Repeatability (RMS) | under 1 μrad |
| Marking Speed | under 2 m/s |
| Positioning Speed | under 6 m/s |
| Gain Drift | under 15 ppm/K |
| Zero Drift | under 10 μrad/K |
| 8-Hour Drift (after 30 min warm-up) | under 0.03 mrad |
| Electrical Parameters | |
|---|---|
| Power Supply | ±15 V / 10 A |
| Input Signal Protocol | XY2-100 / SL2-100 |
| Cooling Method | Water cooling |
| Mechanical Parameters | |
|---|---|
| Operating Temperature | 25±10 °C |
| Dimensions (L×W×H) | 210 × 170 × 185 mm |
| Weight | 8.5 kg |
Operating Principle
A laser galvo scanning system is a high-precision beam positioning device based on electromagnetic deflection. Two orthogonally mounted galvo motors drive the X-axis and Y-axis mirrors, steering the incoming laser beam to any point on the work plane and forming a two-dimensional scan field. A galvo motor is essentially a limited-rotation servo motor: when the driver board feeds control current into the motor coil, electromagnetic torque drives the rotor and mirror to the commanded angle, while a position sensor (an analog position detector, APD, or a digital encoder) measures rotor angle in real time and compares it with the command to close the servo loop. Digital closed-loop galvos replace the traditional analog position detector with a high-resolution encoder that reads rotor angle directly and feeds it back to the digital servo driver board, forming fully digital closed-loop control. This eliminates the noise, drift and hysteresis inherent in analog detectors and delivers sub-microradian positioning accuracy with long-term stability. Scan speed depends on the dynamic response of the motor; tracking time expresses how far the galvo lags the command signal and is the key indicator of high-speed performance.
Applications
Laser Welding
Suited to precision welding of stainless steel, carbon steel, aluminium alloy, copper alloy and other metals, covering spot welding, seam welding, butt welding, lap welding and other seam types, with clean bead formation, a small heat-affected zone and high welding speed.
New Energy Vehicles
Used for welding power-battery cells, battery module busbars, motor stators and other core new-energy-vehicle components, meeting high safety and high consistency requirements.
3C Electronics
Suited to welding phone mid-frames, notebook housings, connectors and other precision electronic parts, with fine weld spots and low distortion for miniaturised production.
Aerospace
Used for repair welding of aero-engine blades and welding of titanium alloy structural parts and other high-end applications, with reliable weld quality that meets stringent industry standards.
Medical Devices
Suited to welding medical catheters, stents and surgical instruments, with high weld cleanliness that meets medical-grade quality requirements.
Hardware Products
Used for automated welding of kitchen and bathroom hardware, locks, valves and other hardware products, with high efficiency and good consistency that significantly reduce labour cost.
Power and Electrical
Suited to welding transformer copper busbars, switchgear busbars and electrical contacts, with good conductivity and low contact resistance.
Selection Guide
When choosing a welding galvo, first fix the required clear aperture from the laser power: up to 1500 W a 14 mm aperture is enough, 1500–3000 W calls for a 20–30 mm aperture, and above 3000 W you need a large aperture of 33 mm or more. Next choose the model by welding speed requirement: the 30G standard series for conventional welding, the 30BS high-speed series for fast welding, and the 30G-FB2 digital closed-loop series where high repeatability and low drift are required. For ultra-high-power welding above 6000 W, the LHP33-FB2 is the first choice. Welding galvos must be water cooled, and the f-theta focal length should be chosen from seam width and working distance together.
Series Comparison
| Model | Clear Aperture | Max Power | Welding Speed | Repeatability | Control | Cooling | Reference Price |
|---|---|---|---|---|---|---|---|
| 14AW-III-Pro-SQU | 14 mm | 1500 W | under 2 m/s | under 2 μrad | Open loop | Water cooling | On request |
| S20GW-Pro-QU | 20 mm | 2000 W | under 2.5 m/s | under 2 μrad | Open loop | Water cooling | On request |
| 30G | 30 mm | 4000 W | under 2.5 m/s | under 2 μrad | Open loop | Water cooling | On request |
| 30BS | 30 mm | 3000 W | under 3 m/s | under 2 μrad | Open loop | Water cooling | On request |
| 30G-FB2 | 30 mm | 4000 W | under 2.5 m/s | under 1 μrad | Digital closed-loop | Water cooling | On request |
| 30GH-SYS | 30 mm | 4000 W | under 2.5 m/s | under 2 μrad | Open loop | Water cooling | On request |
| 30GH-FB2-SYS | 30 mm | 3000 W | under 3 m/s | under 1 μrad | Digital closed-loop | Water cooling | On request |
| LHP33-FB2-SYS | 33 mm | 12000 W | under 2 m/s | under 1 μrad | Digital closed-loop | Water cooling | On request |
About the Brand
Shenzhen Zhibotaike Technology Co., Ltd. (ZBTK) is a leading Chinese manufacturer of laser galvo scanners with more than ten years of galvo development and production experience. Its range covers 2D scanning galvos, 3D dynamic-focus galvos, welding galvos and OCT galvo motors, and is widely used in laser marking, welding, cutting, 3D printing and medical aesthetics. ZBTK scanners are known for cost-effectiveness and stability, can replace comparable imported products, and enjoy a solid reputation in China’s laser industry.
Contact Us
For more product information, a quotation or technical advice, please contact us:
📞 Hotline: +86 159-2722-0467
🌐 Website: www.soar-laser.cn
We provide professional galvo scanner selection advice and complete system integration solutions. You are welcome to call us.





Reviews
There are no reviews yet.