On the front lines of laser marking and cutting, we are constantly wrestling with heat. Carbon steel marks turning black, stainless steel color marks coming out blotchy, plastic edges melting, glass cracking during drilling—these recurring pain points all come down to thermal effects exceeding the threshold the process can tolerate.
1. First, Understand the “Terms”—A 5-Minute Primer
- Heat-affected zone (HAZ): the area “scorched” during processing. When the laser strikes, beyond the mark we want, it also heats the surrounding material—that affected range is the heat-affected zone, and the smaller the better.
- Thermal relaxation time: how long a material takes to “cool down.” An iron plate scalds the hand while an aluminum plate feels less hot, because iron dissipates heat slowly.
- Energy density: how “intense” the laser is. The same 20 W of power feels completely different spread out like a flashlight beam versus concentrated like a needle tip.
- Pulse width: how long each laser pulse lasts. The shorter the pulse width, the sooner processing ends—before heat has time to spread. That is the principle of “cold processing.”
- Absorptivity: whether the material “takes in” the laser’s energy. Black clothes absorb heat, white clothes reflect it; materials behave the same way.
- Spot size: the point where the laser “lands on the material.” The smaller the spot, the more concentrated the energy and the finer the marked line.
2. Where Thermal Effects Come From—Three Major Sources Explained
2.1 Type 1: Source-Level Waste Heat—The Laser “Cannot Get Into” the Material and Heat Piles Up on the Surface
Wavelength and Material “Mismatch”
| Material | 1064 nm IR | 532 nm green | 355 nm UV | 266 nm deep UV |
|---|---|---|---|---|
| Aluminum alloy | 12% | 25% | 40% | 60% |
| Stainless steel | 35% | 50% | 70% | 85% |
| Copper | 5% | 15% | 40% | 55% |
| Glass | 3% | 15% | 75% | 90% |
| Plastic | 60% | 45% | 80% | 95% |
Absorptivity is like a material’s “appetite.” Some materials are “hungry” (they love infrared light), while others are “picky eaters” (they only take ultraviolet light). If a material does not “eat” a given laser wavelength, the laser energy either passes through or bounces back instead of turning into heat. This is exactly why marking glass with infrared light tends to crack it—glass does not “eat” infrared light, so the energy wanders around inside.
Quick reference: glass—loves UV light; copper—loves green/UV light; stainless steel—takes a bit of everything, prefers UV; plastic—eats everything.
Spot Too Large—Energy “Spread Too Thin”
Energy density formula: intensity = total power ÷ irradiated area. With 20 W of power, a 100 μm diameter spot gives “intense” energy density; a 200 μm diameter spot gives only 1/4 of it.
| Spot size | Suitable application | Plain-language note |
|---|---|---|
| 20-30 μm | Fine marking | As fine as a human hair |
| 50-80 μm | Standard marking | About the width of a pen tip |
| 100-200 μm | Cutting, welding | About the size of a ballpoint pen tip |
2.2 Type 2: Process-Induced Accumulated Heat—“Firing Too Fast: Heat Has Not Dissipated Before the Next Pulse Arrives”
Thermal Relaxation Time—The Material’s “Cooling Speed”
| Material | Plain analogy | Thermal relaxation time | Tuning advice |
|---|---|---|---|
| Glass | A thermos—slow to cool | 500-2000ns | Wait a long time before pulsing again |
| Plastic | Foam—insulates too | 2000-10000ns | Keep the frequency low |
| Stainless steel | An iron plate—passable | 80-200ns | Medium frequency |
| Aluminum alloy | An aluminum can—cools fast | 10-50ns | Can pulse faster |
Frequency design principle: fire a pulse → let the material cool → fire the next one. For glass drilling, a frequency ≤100 kHz is recommended; for stainless steel color marking, 20-80 kHz; for plastic marking, 10-30 kHz.
Pulse Overlap—The Culprit Behind “Overheating”
How to judge heat accumulation: pulse interval < thermal relaxation time → heat stacks up → colors drift and darken; pulse interval >> thermal relaxation time → heat dissipates → pure colors.
| Problem | Cause | Plain-language explanation |
|---|---|---|
| Stainless steel color shows a “heat haze” | Low frequency + long pulse width + high power | Too much heat dumped in one spot |
| Carbon steel darkens underneath | Frequency too low, heat accumulates | The next pulse arrives before the first one’s heat dissipates |
| Plastic edges char | Frequency too low, pulse width too long | Plastic is heat-sensitive to begin with |
2.3 Type 3: Process-Stacked Heat (The Most Easily Overlooked!)
How Scan Paths Affect Heat Distribution
| Fill pattern | Heat distribution trait | Best suited for |
|---|---|---|
| Linear fill (dense) | Heat piles up like a mountain along the scan lines | Fine lines |
| Large serpentine fill | Heat spreads into concentric circles | Large-area patterns |
| Bow-shaped fill | Heat spreads along arcs | Curves and gradient colors |
| Spiral fill | Heat keeps pushing outward | Circular marks |
Tuning mantra: “If lines are too dense, widen the hatch spacing; if speed is too slow, raise the jump speed; if depth is not enough, run more light passes.”
3. How to Control Heat—A Full-Chain Design from “Blocking” to “Channeling”
3.1 Shrink the Focused Spot—Make the Energy “More Concentrated and More Intense”
| Application | Recommended setup | Plain-language note |
|---|---|---|
| Fine marking | FL100 F-Theta lens + 10x beam expander | Short focal length + large expansion |
| Standard marking | FL160 F-Theta lens + 6x beam expander | Mid-range configuration |
| Large-format marking | FL254 F-Theta lens + 4x beam expander | Long focal length |
3.2 Switch to a “Colder” Light Source—Cut Heat at the Root
| Laser type | “Coldness” level | Plain-language explanation |
|---|---|---|
| IR continuous wave | ★ | Like “burning”—heat soaks in slowly |
| IR nanosecond | ★★ | Heat melting, long interaction time |
| Green nanosecond | ★★★ | Moderate—heat present but controllable |
| UV nanosecond | ★★★★ | Approaching “cold processing,” small heat effect |
| UV picosecond | ★★★★★ | “Cold processing”—finishes before heat spreads |
| Femtosecond | ★★★★★★ | The most advanced “cold processing,” almost no heat |
| Material | Recommended light source | One-line reason |
|---|---|---|
| Stainless steel color marking | UV 355 nm + nanosecond/picosecond | Short wavelength = strong punch |
| Transparent glass | UV 266 nm or 355 nm | UV is a must |
| Anodized aluminum | 355 nm UV + MOPA laser source | MOPA offers adjustable pulse width |
| Plastic | Green 532 nm or UV 355 nm | Plastic fears heat |
| Copper | Green 532 nm or UV 355 nm | Poor infrared absorption |
3.3 Channel Heat Away Through Process Logic—Give Heat an “Outlet”
Color marking parameter quick reference: light colors → high frequency + wide spacing + low power; dark colors → low frequency + dense spacing + high power.
Multiple light passes: rather than one “heavy” pass, use several “light” passes. Depth per pass: 20-30% of the final depth; wait between passes: about 0.5-2 s; total passes: 3-5 passes beat 1 pass.
To put it plainly: to roast a chicken, blasting it over high heat once leaves it charred outside and raw inside; roasting it over medium-low heat in five rounds, letting it rest a while between rounds, cooks it through and through.
| Gas | Function | Plain-language explanation |
|---|---|---|
| Nitrogen | Oxygen shielding, oxidation prevention, heat removal | Blows heat away + protection |
| Compressed air | Cooling, slag blowing | Cheap and versatile |
| Argon | Complete oxygen shielding | Reserved for precious metals |
| Helium | Strong cooling | Thin-sheet precision processing |
4. Parameter Reference Tables for Typical Materials
4.1 Metallic Materials
| Material | Recommended laser | Pulse width | Frequency | Key caution |
|---|---|---|---|---|
| Carbon steel | 1064 nm IR | 50-150ns | 20-50kHz | Avoid heat buildup or the base layer turns black |
| Stainless steel | 1064 nm / 355 nm UV | 8-30ns | 30-80kHz | Use UV for color marking, better heat control |
| Aluminum alloy | 1064 nm IR | 50-200ns | 30-50kHz | Aluminum is highly reflective; use slightly higher power |
| Copper | 1064 nm / 532 nm green | 10-50ns | 20-40kHz | Low IR absorption; green light recommended |
| Titanium alloy | 1064 nm / 532 nm green | 20-80ns | 20-50kHz | Nitrogen shielding to prevent oxidation |
4.2 Non-Metallic Materials
| Material | Recommended laser | Pulse width | Frequency | Key caution |
|---|---|---|---|---|
| Glass | 355 nm / 266 nm UV | 1-15ns | 50-100kHz | Must use UV, otherwise it cracks |
| Plastic | 1064 nm / 355 nm UV | 10-50ns | 10-30kHz | Avoid heat buildup or edges will melt |
| Anodized aluminum | 355 nm UV | 5-20ns | 30-60kHz | MOPA laser source, uniform blackness |
| Ceramic | 1064 nm / 355 nm UV | 20-100ns | 10-30kHz | Poor thermal conductivity, do not run too fast |
5. Troubleshooting Table for Common Problems
| What went wrong | Most likely cause | How to fix it |
|---|---|---|
| Metal marks come out black/gray | High power, low frequency, heat buildup | Reduce power by 10-20% and raise frequency |
| Edges melt away | Energy too concentrated, scan lines too close | Reduce spot size, raise jump speed, widen hatch spacing |
| Colors blotchy/uneven | Long pulse width, unstable frequency, insufficient gas | Narrow the pulse width, switch to MOPA, add gas assist |
| Glass cracks | Concentrated energy, short pulse interval | Switch to UV, raise jump speed, reduce pulse energy |
| Plastic marks char | Heat accumulation, pulse width too long | Raise frequency, narrow pulse width, fewer passes |
| Marking depth insufficient | Not enough energy, wrong pulse width | Increase power or reduce speed, adjust pulse width |
| Back side darkens (light-transmitting materials) | Back-side heat reflection, pulse overlap | Reduce back reflection, fewer passes, lower frequency |
6. Summary: The Essence of Heat Control Is Managing How Heat Comes and Goes
Thermal effect control, in plain terms, means managing heat: make the laser energy arrive concentrated and leave clean.
| Goal | How to do it | Result |
|---|---|---|
| Arrive concentrated | Energy focused on a tiny point, each pulse very short | Precise processing |
| Leave clean | Give heat enough time to dissipate; do not let it pile up at the work zone | Pure colors |
Once you grasp this logic, you no longer have to tune by blind trial and error—parameters can be designed straight from the principles. That is the difference between an ordinary operator and a senior process engineer.
Appendix: Mini Glossary of Technical Terms
- Heat conduction equation: the mathematical formula describing how heat moves and accumulates within a material
- Thermal diffusion length: the maximum distance the heat from one pulse spreads after the laser pulse ends
- Pulse overlap effect: heat accumulates when the next pulse arrives before the previous pulse’s heat has dissipated
- Heat haze: a ring of darkening or blotchy color around the marking area caused by heat spreading
- Focused spot: the smallest light point after the laser is focused; the smaller the spot, the more concentrated the energy
- Beam expander: an optic that enlarges the laser beam, which allows the focused spot to be made smaller
- F-Theta lens: the lens in a marking machine that focuses the laser; the shorter the focal length, the smaller the focused spot
- MOPA laser source: a laser whose pulse width can be flexibly adjusted, allowing precise control of how long each pulse lasts
- Photodecomposition: a short-wavelength processing mechanism that breaks molecular bonds directly, producing almost no excess heat
- Coulomb explosion: a femtosecond-laser-specific mechanism that blasts material into atomic-scale fragments with extremely fast pulses
- Multiple light passes: splitting a single full-power pass into several low-power passes with enough cooling time in between
- Jump speed: how fast the beam jumps from one scan line to the next; the faster the jump speed, the less heat piles up at the jump points
- Hatch spacing: the distance between two adjacent scan lines; spacing that is too small causes heat to stack up
The parameters in this article are based on industry-standard ranges. For actual applications, please verify against your equipment model and your material supplier’s technical documentation. Source: WeChat official account “Soar Laser Accessories”



Leave a Reply